Peugeot 807 Dag 2007.5 Workshop Manual

523 - Setting the air flow
Turn control knob 3 to the right or
to the left respectively to increase
or reduce the flow of air.
Avoid prolonged operation in interior
air recirculation mode (risk of misting
of the windows and of deterioration of the air
quality).
5 - Air conditioning ON/OFF
The air conditioning is intended to
operate in all seasons. In summer
it allows the temperature to be
reduced and in winter, above 0° C, it
increases the effectiveness of the demisting.
Press switch 5.
The air conditioning indicator light 5 comes
on if the air flow is sufficient.
Pressing this button again switches off the
air conditioning. 4 - Intake of exterior air/
Recirculation of interior air
Press button
4 to recirculate the
air inside.
The air recirculation indicator light 4 comes on.
Recirculation insulates the passenger
compartment from external odours and fumes.
Used simultaneously with the air
conditioning 5, recirculation improves the
performance of the system when set to hot
as well as to cold. Recommended settings for the air conditioning
For optimum operation of the manual system, it is r
ecommended:
If I require...Air
distribution Temperature Air flow
Air
recirculationAC
Heating -
Cooling Deicing
Demisting
With Automatic Air Conditioning, operation in AUTO mode is recommended, irrespective of
the requirement.
Remember to switch it off when the ambient air suit s your requirements.
Ventilation

ERGONOMICS and COMFORT53
3
AUTOMATIC AIR CONDITIONING WITH SEPARATE SETTINGS
Do not cover the sunshine sensor
located in the centre of the fascia. This
is used to regulate the air conditioning.Located on the centre console, the control
panel is to the right of the gear lever.
The driver and front passenger can each
adjust the air temperature to suit their
requirements.
They can also activate or disarm the rear
ventilation adjustment controls. 1 - AUTO mode
This is the normal air conditioning
operating mode.
Press the "AUTO" button.
Depending on the comfort temperature
selected, the system controls the air
distribution, flow and intake so that the
passenger compartment is comfortable and
has an adequate circulation of air.
You do not have to make any further
adjustments.
When the engine is cold, in order to prevent
a rush of cold air, the ventilation will reach
its optimum level progressively.
The "AUTO" symbol is displayed.
For your comfort, the settings selected when
the ignition is switched off will be retained
when it is switched on again, if the temperature
in the passenger compartment has not
changed significantly; otherwise, operation will
resume in automatic mode.
Refer to the beginning of the
"Ventilation" section of chapter 7.
Ventilation

542 - Driver's temperature adjustment 4 - Adjustment of the air
distribution
Pressing the corresponding
button(s) 4 allows you to position
the air flow towards:
- the windscreen,
- the side vents and the central vents,
- the side vents, the central vents and the footwells,
- the windscreen and the footwells,
- the footwells.
The indicator light corresponding to the
position selected 4 comes on. 5 - Adjustment of the rear
ventilation ("REAR" version)
To permit adjustment of the
ventilation to the rear passengers,
press the REAR button.
The rear ventilation symbol is displayed.
The row 2 side vents air flow adjustment controls are operational and
can be adjusted.
To deactivate the rear
ventilation controls, press
the REAR button again.
The rear ventilation symbol
switches off.
Take care not to obstruct
the side vents and the air
outlets on the floor.
3 - Passenger's temperature
adjustment
The required value is displayed
(from 14 to 28: comfort value = 21).
The maximum difference between the
value displayed for the driver and for the
passenger may not be greater than 5.
If you use these manual adjustments, the
AUTO symbol switches off.
Press the corresponding "+" and "-" buttons
to adjust.
To make the driver and passenger setting
the same:
- air conditioning with "MONO" version, press the MONO button.
- air conditioning with "REAR" version, press the + button for more than two seconds.
On entering the vehicle, the interior
temperature may be considerably lower
(or higher) than is comfortable. It is not
necessary to change the value displayed
in order to quickly obtain the desired level
of comfort. The system will operate at
maximum performance to reach the comfort
value set.
MONO Version
Press this button once to obtain
an even temperature throughout
the passenger compartment. The
reference value is selected by the
driver.
Ventilation

ERGONOMICS and COMFORT55
3
6 - Adjustment of the air flow 
Turn control knob 6 to the right
or to the left respectively to
increase or decrease the air
flow.
On the display, the blades of the fan darken
when the air flow is increased.
7 - Switching the system off  Turn air flow control knob 6 to the left until
the display switches off.
The action disarms all the system functions,
with the exception of demisting of the rear
screen. Your comfort setting is no longer
maintained and switches off.
For your comfort, avoid remaining in the off
position. Operating control knob 6 again or the
"Visibility" button or "AUTO" button
reactivates the system with the values
which were present before it was switched
off.
Flashing of the points in the temperature
setting values indicates that there is a
malfunction of the air conditioning.
Contact your PEUGEOT dealer. 8 - Intake of exterior air/
Recirculation of interior air
 Press this button to recirculate
the air inside.
The air recirculation symbol and indicator
light 8 are displayed.
Recirculation insulates the passenger
compartment from outside smells and
smoke.
9 - Air conditioning On/Off
 Press this button to activate
automatic operation of the air
conditioning.
The symbol and the indicator light 9 are
displayed. Press this button again to switch off the
air conditioning.
The symbol and the indicator light 9 switch off.
Avoid prolonged operation of interior
air recirculation (risk of misting of the
windows and deterioration of air quality).
 Press this button again to return air intake
to automatic control.
ADDITIONAL HEATER
Vehicles fitted with HDI engines may be
fitted with automatic additional heating to
improve your comfort.
However, with the engine at idle or when the
vehicle is stationary, it is normal to notice a
high-pitched whistling and a slight emission
of smoke and odour.Ventilation

ERGONOMICS and COMFORT55
3
6 - Adjustment of the air flow 
Turn control knob 6 to the right
or to the left respectively to
increase or decrease the air
flow.
On the display, the blades of the fan darken
when the air flow is increased.
7 - Switching the system off  Turn air flow control knob 6 to the left until
the display switches off.
The action disarms all the system functions,
with the exception of demisting of the rear
screen. Your comfort setting is no longer
maintained and switches off.
For your comfort, avoid remaining in the off
position. Operating control knob 6 again or the
"Visibility" button or "AUTO" button
reactivates the system with the values
which were present before it was switched
off.
Flashing of the points in the temperature
setting values indicates that there is a
malfunction of the air conditioning.
Contact your PEUGEOT dealer. 8 - Intake of exterior air/
Recirculation of interior air
 Press this button to recirculate
the air inside.
The air recirculation symbol and indicator
light 8 are displayed.
Recirculation insulates the passenger
compartment from outside smells and
smoke.
9 - Air conditioning On/Off
 Press this button to activate
automatic operation of the air
conditioning.
The symbol and the indicator light 9 are
displayed. Press this button again to switch off the
air conditioning.
The symbol and the indicator light 9 switch off.
Avoid prolonged operation of interior
air recirculation (risk of misting of the
windows and deterioration of air quality).
 Press this button again to return air intake
to automatic control.
ADDITIONAL HEATER
Vehicles fitted with HDI engines may be
fitted with automatic additional heating to
improve your comfort.
However, with the engine at idle or when the
vehicle is stationary, it is normal to notice a
high-pitched whistling and a slight emission
of smoke and odour.Ventilation

Seats
56
FRONT SEATS WITH MANUAL
ADJUSTMENT
2 - Seat back angle adjustment
Pull the lever upwards and set the required
angle.
1 - Forwards/backwards adjustment
Lift the bar and slide the seat forwards or
backwards.
SEATS

ERGONOMICS and COMFORT57
3
3 - Driver's seat height adjustment
Manoeuvre the handle upwards or
downwards until the desired position is
reached.
4 - Driver's seat lumbar adjustment
Move the lever up or down to obtain the
required position.5 - Head restraint height and angle
adjustment
To raise or lower the restraint, pull it
forwards, then slide it.
The adjustment is correct when the upper
edge of the head restraint is level with the
top of the head.
To remove it, set it in the high position, lift
the tab using a coin and pull upwards and
forwards at the same time.
To re-install, engage the head restraint rods
in the holes, making sure they are aligned
with the seat back. 6 - Rotating of seats
If your vehicle is fitted with this function:
Place the seat back in the upright position.
Place the seat in the highest intermediate
longitudinal position.
On the driver's side, push the steering
wheel, apply the handbrake. To allow
rotation of the seat, lower the handbrake
handle pulling on the end.
Pull the control upwards and rotate the seat
inwards.
Never drive with the head restraints
removed; they must be in place and
correctly adjusted. This rotating operation must be carried
out with the engine switched off.
The
handbrake, the lever of which is now in the
lower position, remains applied.
Do not forget to raise the lever and release
the brake before setting off.
Driving with a passenger seated facing the
rear is prohibited. For further information regarding the
disengaging of the handbrake, refer to
the "Driving Safety" section of chapter 5.
Seats

Seats
58FRONT SEATS WITH ELECTRICAL
ADJUSTMENT
2 - Driver's seat height adjustment
Push the rear part of the control upwards or
downwards to obtain the required height.
1 - Forwards-backwards adjustment
Push the control forwards or backwards to
slide the seat.

ERGONOMICS and COMFORT59
3
3 - Seat back angle adjustment
Tilt the control to the front or the rear to
obtain the angle required.
The electrical functions of the seats are
cancelled one minute after the ignition
has been switched off.
4 - Driver's seat lumbar adjustment (mechanical)
Raise or lower the lever to obtain the correct
position. 5 - Head restraint height and angle
adjustment (manual)
To raise or lower the head restraint, pull it
forwards, then slide it.
The setting is correct when the upper edge
of the head restraint is level with the top of
the head.
To remove the head restraint, place it in the
high position, lift the tab using a coin and
pull upwards and forwards at the same time.
To re-install, engage the head restraint rods
in the holes, making sure they are aligned
with the seat back.
Never drive with the head restraints
removed; they must be in place and
correctly adjusted.
6 - Rotating of seats (mechanical)
Place the seat back in the upright position.
Place the seat in the highest intermediate
longitudinal position.
On the driver's side, push the steering
wheel, apply the handbrake. To allow
rotation of the seat, lower the handbrake
handle pulling on the end.
Pull the control upwards and rotate the seat
inwards.
This rotating operation must be carried
out with the engine switched off. The
handbrake, the lever of which is now in
the lower position, remains applied. Do not
forget to raise the lever and release the
brake before setting off.
Driving with a passenger seated facing the
rear is prohibited. For further information regarding the
disengaging of the handbrake, refer to
the "Driving safety" section of chapter 5.
Seats

Seats
60
Memorising seat positions
Two driving positions can be memorised,
using buttons M/1 and M/2.
These are located on the side of the seat: Place the ignition key in the "running"
position (2nd notch),
 Adjust your seat,
 Press button M, then button 1 for a first
driving position within four seconds.
Repeat the same actions on buttons M and
2 to store another driving position.
An audible signal confirms that a position
has been memorised.
Memorising a new position cancels the
previous one. Activating a memorised driving
position
Engine off 
Briefly press button 1 or 2 to recall the
corresponding memorised position. Front heated seat controls
When the engine is running, the front seats
can be heated separately.
Use the adjustment controls located on the
side of each front seat to switch on and
select the self-regulated level of heating:
1:
Low.
2: Medium.
3: High.
0: Off.
After recalling a memorised position
five times in succession, the function
will be cancelled until the engine is started.
Engine running  Keep button 1 or 2 pressed down until
the end of setting of the corresponding
memorised position.