Peugeot 807 Dag 2007.5 Repair Manual

ERGONOMICS and COMFORT61
3
Rear side seats
Two rear passenger seats, left and right side posit
ion, rows 2 and 3.Rear centre seat
One rear passenger seat, row 2 central position and
row 3 left side
position. Integrated seat belt. Plastic shell trim. Folds to the low
table position.
Rear bench seat
One three-seat bench seat, row 3. Pullman seat
Equipment dedicated to the special version of the 8
07.
Four rear passenger seats with armrests.
Side position, rows 2 and 3. Seats

Seats
62
REAR SIDE SEATS
Forwards/backwards adjustment
Lift bar A and slide the seat forwards or
backwards.
Adjusting the angle of the seat back
Push lever B upwards and adjust the angle
as required.
Release the lever to lock. cushion and guide the tilting of the seat
back forwards until the rear anchorages
are unlocked. If you experience any
difficulty, use the emergency control to
unlock the anchorages.
4 - Place the seat in the vertical closed
position.
Exit from row 3
1 - Place the head restraint in the low
position.
2 - Pull control C.
3 - Guide the tilting of the seat back
forwards until the rear anchorages
are unlocked. If you experience any
difficulty, use the red emergency control
to unlock the anchorages. 4 -
Place the seat in the vertical closed
position.
Following each entry or exit, reposition
the raised seat guiding it until the rear
anchorages lock in their rails.
Handling the side seat
Access to row 3
1 - Place the head restraint in the low
position.
2 - Push lever B upwards as far as
possible.
3 - Fold the seat back onto the seat

ERGONOMICS and COMFORT63
3
Control for sliding the rear side seats
from row 3 or the boot
Pull the strap (marked with the arrow
symbol) to slide the seat in front of you.Removing the side seat
1 -
Tilt the seat back forwards to detach the
rear anchorages.
2 - Grab the red strap which appears and
pull it upwards, the front anchorages
unlock.
Refitting the side seat 3 -
The strap, like the handle, enables you
to remove the seat.
1 - Place the front anchorages at the front
stop in the slides. Support the strap
firmly for easier positioning of the seat.
2 - Tilt the folded seat towards the rear.
The rear anchorages lock.
3 - Raise the seat back.
4 - Slide the seat.
Check that there is no obstacle
obstructing the slides or preventing
correct locking of the seat anchorages.
Seats

Seats
64
ROW 2 CENTRE SEAT
This can be placed in row 3, on the left."Low table" position
1 -
Place the head restraint in the low
position.
2 - At the top (at the back of the seat), lift
the handle identified by the symbol
and guide the tilting of the seat back
towards its seat cushion. 3 -
You have a "low table". To return to the
seat position, lift the handle and guide
the raising of the seat back.
Removing the centre seat
1 - Place the seat in the "low table"
position.
2 - Using the control which you pull, tilt the
seat back forwards so releasing the rear
anchorages from the slides. 3 -
Grab the red strap which appears and
pull it upwards, the front anchorages
unlock.
4 - The strap, like the handle, enables you
to remove the seat.

ERGONOMICS and COMFORT65
3
Rear head restraints
The rear head restraints can be removed
and have two positions:
high, position for use,
 low, storage position.
To raise or lower a head restraint, pull it
forwards sliding it at the same time.
To remove it, place it in the high position,
push the lug and pull it forwards and upwards.
To refit it, engage the head restraint rods
in the holes taking care to remain in the
centreline of the seat back.
Never drive with the head restraints
removed, they must be in place and
correctly adjusted.
Refitting the centre seat
Check that there is no obstacle
obstructing the slides or preventing
correct locking of the seat anchorages.
1 - Place the front anchorages at the front
stop in the slides. Support the strap
firmly for easier positioning of the seat.
2 - Tilt the folded seat towards the rear.
The rear anchorages lock.
3 - Raise the seat back and slide the seat.
Turning a rear seat round

The rear seats can be placed in a "face to
face" position.
Carry out the operations described for
removal then turn the seat round and
resume with the procedure for refitting the
seat.
This turning operation must be carried
out when stationary.
Driving with a passenger seated facing the
rear is prohibited.
When the vehicle is being driven, placing
a row 2 seat in the closed position while a
passenger is sitting in row 3 is prohibited.
Seats

ERGONOMICS and COMFORT65
3
Rear head restraints
The rear head restraints can be removed
and have two positions:
high, position for use,
 low, storage position.
To raise or lower a head restraint, pull it
forwards sliding it at the same time.
To remove it, place it in the high position,
push the lug and pull it forwards and upwards.
To refit it, engage the head restraint rods
in the holes taking care to remain in the
centreline of the seat back.
Never drive with the head restraints
removed, they must be in place and
correctly adjusted.
Refitting the centre seat
Check that there is no obstacle
obstructing the slides or preventing
correct locking of the seat anchorages.
1 - Place the front anchorages at the front
stop in the slides. Support the strap
firmly for easier positioning of the seat.
2 - Tilt the folded seat towards the rear.
The rear anchorages lock.
3 - Raise the seat back and slide the seat.
Turning a rear seat round

The rear seats can be placed in a "face to
face" position.
Carry out the operations described for
removal then turn the seat round and
resume with the procedure for refitting the
seat.
This turning operation must be carried
out when stationary.
Driving with a passenger seated facing the
rear is prohibited.
When the vehicle is being driven, placing
a row 2 seat in the closed position while a
passenger is sitting in row 3 is prohibited.
Seats

Seats
66
REAR BENCH SEAT
Forwards/backwards adjustment
From the seat cushion, lift bar A and slide
the seat towards the front or the rear.
From the boot, you can pull on strap B
and slide the seat forwards to make it
easier to load the vehicle.
The rear bench seat must only be
fitted in row 3.
Seat back folded position
1 - Place the head restraints in the low
position.
2 - Pull the strap C upwards, from the
tailgate. 3 -
Tilt the seat back on the seat cushion.
Vertical position of the bench seat
1 - Place the head restraints in the low
position.
2 - Pull the strap C upwards, from the
tailgate.
3 - Fold the seat back onto the seat
cushion. 4 -
Pull the lever D to unlock the rear
anchorages.
5 - Place the seat in the vertical "folded"
position.
When driving, attach the retaining
straps to the handles.

ERGONOMICS and COMFORT67
3
Removing the bench seat
1 -
Fold the seat to the vertical position.
2 - Grasp the two bars E underneath the
seat. 3 - The front anchorages
unlock.
Refitting the bench seat
For removal and refitting, pass the rear
seat, in the "folded" position, through
the sliding side doors.
Check that there is nothing blocking
the runners which could prevent correct
locking of the bench seat anchorages.
1 - Position the front anchorages at the
front stop of the runners.
2 - Tilt the folded seat rearwards.
3 - The rear anchorages then lock.
4 - Unlock the seat back and lift it using the
strap C.
Good practice
When the vehicle is being driven, it is
prohibited for a passenger to sit:
- in the 3rd row if the seat back in front (2nd row) is in the table position.
- in the 3rd row if the seat/bench in front (2nd row) is in the vertical folded position.
- in the centre seat if the right-hand side seat is in the vertical folded position.
Seats

Seats
68
The centre seat may be installed in the
central position in row 2 and in the left
side position in row 3.
MODULARITY AND POSSIBLE SEAT CONFIGURATIONS
Examples of various arrangements
combining pleasure and practicality:
The various operations modifying the
existing configuration must be carried
out with the engine switched off (See section
on "Seats").
It is prohibited to be in a rearwards facing
position when the vehicle is being driven.
The rotating of the seats depends on the
vehicle equipment and the country.
5 seats with picnic position when parked 5 seat arrangements

ERGONOMICS and COMFORT69
3
7 seats with access to row 3
8 seats with bench seatSeats