display Peugeot RCZ 2013 User Guide

1/
INSTRUMENTS and CONTROLS




Anti-lock
Braking
System (ABS)


fi xed. The anti-lock braking system has
a fault. The vehicle retains conventional braking.
Drive carefully at reduced speed and contact a PEUGEOT
dealer or a qualifi ed workshop without delay.




Dynamic
stability control

(ESC/ASR)


fl ashing. The ESC/ASR regulation is
active. The system optimises traction and improves the directional
stability of the vehicle.

fi xed. Unless it has been deactivated
(button pressed and its indicator
lamp on) the ESC/ASR system
has a fault. Have it checked by a PEUGEOT dealer or a qualifi ed
workshop.




Directional
headlamps


fl ashing. The directional headlamps
system has a fault. Have it checked by a PEUGEOT dealer or a qualifi ed
workshop.

Warning lamp



is on



Cause



Action / Observations




Seat belt not
fastened /
unfastened


fi xed, then
fl ashing in the
passenger's seat
belt and front
airbag warning
lamp display. The driver or front passenger has
not buckled or has unbuckled
their seat belt.
Pull on the belt in question and insert the tongue in the
buckle.
At least one rear passenger has
unbuckled their seat belt.

1/
INSTRUMENTS and CONTROLS


Warning lamp



is on



Cause



Action / Observations








Rear foglamp


fi xed. The rear foglamp is switched on. Turn the ring on the stalk rearwards to switch off the rear
foglamp.





Diesel engine
pre-heating


fi xed. The ignition switch is at the
2nd position (ignition on). Wait until the warning lamp has switched off before starting.
The duration for which the warning lamp is on is
determined by the climatic conditions.





Parking
brake


fi xed. The parking brake is applied or
not properly released. Release the parking brake to switch off the warning lamp,
keeping your foot on the brake pedal.
Observe the safety recommendations.
For further information on the parking brake, refer to the
"Parking brake" section.



Passenger's
front airbag
fi xed on the
seat belt and
passenger's front
airbag warning
lamps display. The control switch, located on
the passenger's side of the
dashboard, has been placed in
the "ON"
position.
The passenger's front airbag is
activated.
In this case, do not install
a "rear facing" child seat. While you do not have a rear-facing child seat fi tted to
the front passenger seat, it is recommended that the
passenger's front airbag be activated.
On the other hand, before fi tting a rear-facing child seat,
you must turn the control switch to the "OFF"
position.

32










Deactivation warning lamps

If one of the following warning lamps comes on, this confi rms that the
corresponding system has been switched off intentionally.
It is accompanied by an audible signal and a message on the screen.
Depending on your version of instrument panel, illumination of the
deactivation lamp is also accompanied by:


- a symbol in the central instrument panel screen and a message in
the multifunction screen,
or

- a symbol and a message in the central instrument panel screen.




Warning lamp



is on



Cause



Action / Observations






Passenger's
front airbag


fi xed, in the seat
belt and front
passenger's
airbag warning
lamps display. The control switch, located
on the passenger's end of
the dashboard, is set to the
OFF
position.
The passenger's front airbag is
deactivated.
You can install a "rear-facing"
child seat on the front seat. Before installing a "rear-facing" child seat on the front seat,
it is essential
to deactivate the passenger's front airbag.
On the other hand, where no "rear-facing" child seat is
present, it is recommended that the airbag be reactivated:
set the control to the ON
position.




ESC/ASR


fi xed. The button, located in the centre
of the dashboard, is pressed. Its
indicator lamp is on.
The following functions are
deactivated.


- electronic stability
programme (ESC),

- anti-slip regulation or traction
control (ASR),

- automatic operation of
hazard warning lamps. Press the button again to reactivate these functions
manually. Its indicator lamp goes off.
These functions are reactivated automatically when the
vehicle is started.

1/
INSTRUMENTS and CONTROLS












COOLANT TEMPERATURE INDICATOR

With the engine running, when the needle is:


- in zone A
, the temperature is correct,

- in zone B
, the temperature is too high; the maximum temperature
warning lamp and the central STOP
warning lamp come on,
accompanied by an audible signal and an alert message in the
screen.

You MUST stop as soon as it is safe to do so.

Wait a few minutes before switching off the engine.
Contact a PEUGEOT dealer or a qualifi ed workshop.
















ENGINE OIL LEVEL INDICATOR

This information is displayed for a few seconds when the ignition is
switched on, at the same time as the service information.
The vehicle must be on level ground and the engine must have
been off for more than 30 minutes for this level check to be
accurate. After driving for a few minutes, the temperature and pressure in the
cooling system increase.
To top up the level:


)
wait for the engine to cool,

)
unscrew the cap by two turns to allow the pressure to drop,

)
when the pressure has dropped, remove the cap,

)
top up the level to the "MAX" mark.

1/
INSTRUMENTS and CONTROLS






SERVICE INDICATOR

This information is displayed for a few seconds when the ignition is
switched on. It informs the driver when the next service is due, in
accordance with the manufacturer's servicing schedule.
The point at which the service is due is calculated from the last indicator
zero reset. It is determined by two parameters:


- the distance travelled,

- the time elapsed since the last service.


More than 1 800 miles (3 000 km) remain before the next service is due

When the ignition is switched on, no service information appears on the
instrument panel central screen.


Between 600 miles (1 000 km) and 1 800 miles (3 000 km)
remain before the next service is due
For 7 seconds after the ignition is switched on, the spanner symbolising
the service operations comes on. The instrument panel central screen
indicates the distance remaining before the next service is due.

Example:
1 700 miles remain before the next service is due.
For 7 seconds after the ignition is switched on, the central screen
indicates:


Less than 600 miles (1 000 km) remain before the next service is due


Example:
500 miles remain before the next service is due.
For 7 seconds after the ignition is switched on, the central screen
indicates:

The spanner remains on
in the small screen
to indicate that a service must be carried out
soon.

36

Service overdue

For 7 seconds after the ignition is switched on, the spanner fl ashes
to
indicate that the service must be carried out as soon as possible.

Example:
the service is overdue by 300 miles.
For 7 seconds after the ignition is switched on, the central screen indicates:

The spanner remains
on
in the small screen
to indicate that a service should have been
carried out.
The distance remaining may be weighted by the time factor,
depending on the driver's driving habits.
Therefore, the spanner may also come on if you have exceeded
the one year service interval.









Service indicator zero reset

Retrieving the service information

You can access the service information at any time.
This information appears when running through the manual check
procedure.


)
Briefl y press the "CHECK/000"
button.
The service information is displayed for a few seconds on the
instrument panel central screen, then disappears.

Following this operation, if you wish to disconnect the battery, lock
the vehicle and wait at least fi ve minutes for the zero reset to be
registered. After each service, the service indicator must be reset to zero.
The procedure for resetting to zero is as follows:


)
switch off the ignition,

)
press and hold the "CHECK/000"
button,

)
switch on the ignition; the distance recorder display begins a
countdown,

)
when the instrument panel central screen indicates "=0"
, release
the button; the spanner disappears from the small screen.

1/
INSTRUMENTS and CONTROLS












MANUAL CHECK

This function allows you to check the status of the vehicle (reminder of
the active alert warnings) and the service information.


)
With the engine running, to start a manual check, briefl y press the
"CHECK/000"
button on the instrument panel.
If no faults have been detected, "CHECK OK"
appears in the
instrument panel central screen.
If a "minor" fault has been detected, the warning lamp concerned then
"CHECK OK"
appear in the instrument panel central screen. Contact a
PEUGEOT or a qualifi ed workshop.
If a "major" fault has been detected, only the warning lamps concerned
appear in the instrument panel central screen. Have it checked by a
PEUGEOT dealer or a qualifi ed workshop.













DISTANCE RECORDERS

The total and trip distances are displayed for thirty seconds when the
ignition is switched off, when the driver's door is opened and when the
vehicle is locked or unlocked.
Measures the total distance travelled by the vehicle since its fi rst
registration.



Total distance recorder



)
With the ignition on, press and hold this button until zeros appear.



Trip distance recorder

Measures the distance travelled since it was last reset to zero by the
driver.

1/
INSTRUMENTS and CONTROLS

DATA DISPLAYS



)
Press the button, located at the end of the wiper stalk
, to display
the various trip computer tabs in succession.



)
Press the up and down arrows on the navigator for the instrument
panel with large central screen to display the various trip computer
tabs in succession.



With the large central screen
TRIP COMPUTER











Instrument panel with small central screen

Instrument panel with large central screen

With the small central screen


System that gives you information on the journey in progress (range,
fuel consumption…).

1
2
40



- The current information tab with:


●
the range,

●
the current fuel consumption.



- The trip "1"
tab with:


●
the distance travelled,

●
the average fuel consumption,

●
the average speed,
for the fi rst trip.



- The trip "2"
tab with:


●
the distance travelled,

●
the average fuel consumption,

●
the average speed,
for the second trip.



)
Pressing the button again takes you to a black screen.
A further press returns you to the normal display.



TRIP ZERO RESET



)
When the trip required is displayed, press the button at the end of
the wiper stalk
for more than two seconds.



With the large central screen



)
When the required trip is displayed, press the "OK"
button on the
navigator
for the instrument panel with large central screen.



With the small central screen


Trips "1"
and "2"
are independent but their use is identical.
Trip "1"
permits, for example, daily calculations, and trip "2"
monthly
calculations.

1/
INSTRUMENTS and CONTROLS






TRIP COMPUTER, A FEW DEFINITIONS


Range

(miles or km)
The distance which can still be travelled with the fuel
remaining in the tank. Related to the average fuel consumption over the
last few miles (kilometres) travelled.

This value may vary following a change in the style of driving
or the relief, resulting in a signifi cant change in the current fuel
consumption.

If dashes are displayed continuously while driving in place of the
digits, contact a PEUGEOT dealer or a qualifi ed workshop.

This function is only displayed from 20 mph (30 km/h).
When the range falls below 20 miles (30 km), dashes are displayed.
After fi lling with at least 5 litres of fuel, the range is recalculated and is
displayed when it exceeds 60 miles (100 km).


Current fuel consumption

(mpg or l/100 km or km/l)
Calculated over the last few seconds.


Average fuel consumption

(mpg or l/100 km or km/l)
Calculated since the last trip computer reset.


Average speed

(mph or km/h)
Calculated since the last trip computer reset.


Distance travelled

(miles or km)
Calculated since the last trip computer reset.