hood open PONTIAC SOLSTICE 2007 Owners Manual

Filling a Portable Fuel Container
{CAUTION:
Never ll a portable fuel container while it
is in your vehicle. Static electricity
discharge from the container can ignite the
gasoline vapor. You can be badly burned
and your vehicle damaged if this occurs.
To help avoid injury to you and others:
Dispense gasoline only into approved
containers.
Do not ll a container while it is inside a
vehicle, in a vehicle’s trunk, pickup
bed, or on any surface other than the
ground.
Bring the ll nozzle in contact with the
inside of the ll opening before
operating the nozzle. Contact should
be maintained until the lling is
complete.
Do not smoke while pumping gasoline.
Checking Things Under
the Hood
{CAUTION:
An electric fan under the hood can start up
and injure you even when the engine is not
running. Keep hands, clothing, and tools
away from any underhood electric fan.
{CAUTION:
Things that burn can get on hot engine
parts and start a re. These include
liquids like fuel, oil, coolant, brake uid,
windshield washer and other uids, and
plastic or rubber. You or others could be
burned. Be careful not to drop or spill
things that will burn onto a hot engine.
242

Hood Release
To open the hood, do the following:
1. Locate the interior
hood release lever.
It is located below
the instrument panel
on the driver’s side
of the vehicle.
2. Pull down on the
rear edge of the
lever to release
the hood latch.3. Go to the side of the vehicle and pull up on
the rear edge of the hood, near the windshield
to open the hood.
Notice:Closing the hood with the doors open
may damage the hood and/or doors. Always
close the doors before closing the hood.
Before closing the hood, be sure all the ller caps
are on properly. Then, pull the hood down and
close it rmly.
243

Engine Compartment Overview
When you open the hood on the 2.4L L4 engine, this is what you will see:
244

When you open the hood on the 2.0L L4 engine, this is what you will see:
246

If Steam Is Coming From Your Engine
{CAUTION:
Steam from an overheated engine can
burn you badly, even if you just open the
hood. Stay away from the engine if you
see or hear steam coming from it. Just
turn it off and get everyone away from
the vehicle until it cools down. Wait until
there is no sign of steam or coolant
before you open the hood.
If you keep driving when your engine is
overheated, the liquids in it can catch re.
You or others could be badly burned.
Stop your engine if it overheats, and get
out of the vehicle until the engine is cool.
Notice:If your engine catches re because
you keep driving with no coolant, your vehicle
can be badly damaged. The costly repairs
would not be covered by your warranty.
If No Steam Is Coming From Your
Engine
An engine coolant temperature warning can
indicate a serious problem. SeeEngine Coolant
Temperature Warning Light on page 137.
If you get an engine coolant temperature warning,
but see or hear no steam, the problem may not
be too serious. Sometimes the engine can
get a little too hot when you:
Climb a long hill on a hot day.
Stop after high-speed driving.
Idle for long periods in traffic.
If you get the engine coolant temperature warning
with no sign of steam, try this for a minute or so:
1. If your air conditioner is on, turn it off.
2. In heavy traffic, let the engine idle in
NEUTRAL (N) while stopped. If it is safe to
do so, pull off the road, shift to PARK (P)
or NEUTRAL (N) and let the engine idle.
3. Turn on your heater to full hot at the highest
fan speed and open the windows as
necessary.
261

Notice:If you leave your radio or other
accessories on during the jump starting
procedure, they could be damaged. The repairs
would not be covered by your warranty.
Always turn off your radio and other
accessories when jump starting your vehicle.
3. Turn off the ignition on both vehicles.
Unplug unnecessary accessories plugged into
the cigarette lighter or the accessory power
outlet. Turn off the radio and all lamps that
are not needed. This will avoid sparks
and help save both batteries. And it could
save the radio!4. Open the hood on the other vehicle and
locate the positive (+) and negative (−)
terminal locations on that vehicle.
You will not need to access your battery for
jump starting. Your vehicle has a remote
positive (+) and a remote negative (−) jump
starting terminal.
The remote positive (+)
terminal is located
under a red plastic
cover on the engine
compartment fuse block.
Open the cover to
access the terminal.
275

Bulb Replacement
For the proper type of replacement bulbs, see
Replacement Bulbs on page 283.
For any bulb changing procedure not listed in this
section, contact your dealer.
Halogen Bulbs
{CAUTION:
Halogen bulbs have pressurized gas
inside and can burst if you drop or
scratch the bulb. You or others could be
injured. Be sure to read and follow the
instructions on the bulb package.
Headlamps
To replace the low/high-beam/Daytime Running
Lamps (DRL) headlamp bulb, do the following:
1. Open the hood. SeeHood Release on
page 243for more information.
2. Locate the headlamp bulb socket.3. Turn the bulb socket counterclockwise and
pull it from the headlamp assembly.
4. Holding the base of the socket, pull the old
bulb from the socket.
5. Replace with a new bulb.
6. Reverse Steps 3 through 4 to reinstall.
280

Front Turn Signal, Parking and
Fog Lamps
A. Front Turn Signal/
Parking Lamp
B. Fog Lamp
(If Equipped)
To replace one of these bulbs, do the following:
1. Open the hood. SeeHood Release on
page 243for more information.
2. Reach underneath the front bumper and
locate the bulb assembly.
3. Turn the bulb socket counterclockwise and
pull out the bulb assembly.
4. Disconnect the bulb socket from the wiring
harness.
5. Install a new bulb.
6. Reverse the steps to reinstall the bulb
assembly and headlamp assembly.
Taillamps, Turn Signal, and
Stoplamps
To replace one of these bulbs, do the following:
1. Open the trunk. SeeTrunk on page 68
for more information.
2. Remove the two screws, which hold the
taillamp assembly, from inside the vehicle.
3. Remove the taillamp assembly.
4. Turn the bulb socket counterclockwise to
remove.
5. Pull the bulb from the socket.
6. Install a new bulb.
7. Reverse the steps to reinstall the taillamp
assembly.
281