trunk release PONTIAC SOLSTICE 2009 Owners Manual

Remote Keyless Entry (RKE)
System Operation
The Remote Keyless Entry (RKE) transmitter functions
work up to 60 feet (18 m) away from the vehicle.
There are other conditions which can affect the
performance of the transmitter. SeeRemote Keyless
Entry (RKE) System on page 2-3.
Q(Lock):Press to lock all the doors. If enabled
through the Driver Information Center (DIC), the parking
lamps may ash once and the horn may chirp to
indicate locking has occurred. See “LOCK HORN” under
DIC Vehicle Personalization on page 3-41.
K(Unlock):Press once to unlock the driver door.
Press
Kagain within ve seconds to unlock the other
doors. The interior lamps come on and stay on for
20 seconds or until the ignition is turned on. If enabled
through the DIC, the parking lamps ash once to
indicate unlocking has occurred. See “UNLOCK HORN”
underDIC Vehicle Personalization on page 3-41.
V(Trunk Release):Press and hold for
approximately one second to unlock the trunk. The trunk
release only works if the ignition is off or the vehicle
speed is less than 2 mph (3 km/h).
L(Vehicle Locator/Panic Alarm):Press and release
to locate the vehicle. The horn sounds three times
and the parking lamps ash three times.
Press and hold
Lfor three seconds to sound the panic
alarm. The horn sounds and the parking lamps ash
for 30 seconds. The ignition must be off for the vehicle
locator/remote alarm to work. Press
Lagain or
turn the ignition to ACC/ACCESSORY or ON/RUN to
turn off the alarm.
The vehicle may have Remote Lock/Unlock
Conrmation. This feature provides feedback that a
command has been received by the vehicle. The parking
lamps ash and the horn may sound briey. See
“LOCK HORN” and “UNLOCK HORN” underDIC
Vehicle Personalization on page 3-41for programming
information.
2-4

Trunk
To release the trunk lid use either the Remote Keyless
Entry (RKE) transmitter, or see “Remote Trunk
Release” following.
To close the trunk, push down rmly from the rear
center of the trunk lid.
{CAUTION:
Exhaust gases may enter the vehicle if it is driven
with the liftgate, trunk/hatch open, or with any
objects that pass through the seal between the
body and the trunk/hatch or liftgate. Engine
exhaust contains Carbon Monoxide (CO) which
cannot be seen or smelled. It can cause
unconsciousness and even death.
CAUTION: (Continued)
CAUTION: (Continued)
If the vehicle must be driven with the liftgate, or
trunk/hatch open:
Close all of the windows
Fully open the air outlets on or under the
instrument panel
Adjust the Climate Control system to a setting
that brings in only outside air and set the fan
speed to the highest setting. See Climate
Control System in the Index.
If the vehicle is equipped with a power liftgate,
disable the power liftgate function.
For more information about carbon monoxide, see
Engine Exhaust on page 2-27.
2-8

Remote Trunk Release
To open the trunk from
inside the vehicle, press
the remote trunk release
button located in the
glovebox.
The remote trunk release will only work when either the
ignition is off or in ACC/ACCESSORY, the parking
brake is engaged, or the vehicle speed is less than
2 mph (3 km/h).
Emergency Trunk Release Handle
Notice:Do not use the emergency trunk release
handle as a tie-down or anchor point when securing
items in the trunk as it could damage the handle.
The emergency trunk release handle is only
intended to aid a person trapped in a latched trunk,
enabling them to open the trunk from the inside.
There is a glow-in-the-dark emergency trunk release
handle located inside the trunk on the driver’s side. This
handle will glow following exposure to light. If someone
is locked in the trunk, they can pull the release
handle and push the trunk lid open from the inside to
open the trunk.
2-9

Arming the System
While the ignition is off, press the Remote Keyless Entry
(RKE) transmitter lock button, to arm the system.
The system will arm after either of these things occur:
Thirty seconds after all the doors are closed.
Sixty seconds with any door open.
If you press the lock button on the transmitter a second
time while all the doors are closed, the system will
arm immediately. The system arms in 60 seconds if a
door is open, or after the open door is closed.
If you do not want to arm the system, lock the car with
the manual door lock knobs.
Disarming the System
To disarm the system:
Press the unlock button on the RKE transmitter.
Turn the ignition on.
If the system is armed and the trunk is opened using
the trunk release button on the transmitter, the system
will temporarily disarm itself and re-arm when the
trunk has been closed. This allows you to exit the
vehicle, lock the doors using the transmitter, or open the
trunk using the transmitter without having to disarm
and re-arm the system.
Once the system is disarmed, the security light will stop
ashing.
How the System Alarm is Activated
To activate the system if it is armed:
Open the driver’s door or trunk. This causes a ten
second pre-alarm chirping noise followed by the
horn sounding and lights ashing for 30 seconds.
Open a passenger’s door. This immediately causes
a full alarm of the horn sounding and lights ashing
for 30 seconds.
After the 30 second alarm ends, the system will
re-arm itself.
How to Turn Off the System Alarm
To turn off the system alarm, do one of the following:
Press the lock button on the RKE transmitter.
The system will then re-arm itself.
Press the unlock button on the RKE transmitter.
This will also disarm the system.
Insert the key in the ignition and turn it on. This will
also disarm the system.
How to Detect a Tamper Condition
If you hear three chirps when you press the unlock, lock,
or trunk release buttons on the RKE transmitter, it
means that the content theft security system alarm was
activated previously.
2-13

6. Pull rearward on the side edge (B) of the convertible
top and pull it off of the windshield frame.
7. Push the convertible top down into the trunk (E).
8. After the top is stored, as shown, push on the
convertible top to ensure that the top is fully
retracted and securely stored.
9. Close the trunk (E) by pressing down from the rear
center of it with a swift, rm motion.
Do not operate the rear defogger when the convertible
top is down.Raising the Manual Convertible Top
1. Park on a level surface, set the parking brake rmly
and shift an automatic transmission into (P) Park.
Shift a manual transmission into (1) First or
(R) Reverse.
2. Turn off the ignition, and lower the windows.
3. Push the trunk release button located in the glove
box, or on the remote keyless entry, if equipped.
4. Open the trunk.
5. Pull the convertible top forward by rmly gripping the
side edge (B) and applying a brisk upward and
forward motion to get the top in the full-up position.
2-39

The main components of the instrument panel are the
following:
A. Side Window Outlets. SeeClimate Control System
on page 3-16.
B.Outlet Adjustment on page 3-19.
C.Turn Signal/Multifunction Lever on page 3-6.
D.Cruise Control on page 3-9(If Equipped).
E.Instrument Panel Cluster on page 3-20.
F.Audio Steering Wheel Controls on page 3-79
(If Equipped).
G.Instrument Panel Brightness on page 3-14.
H.Passenger Airbag Status Indicator on page 3-24.
I.Hazard Warning Flashers on page 3-5.
J.Fog Lamps on page 3-13(If Equipped).
K. Electronic Stability Control (ESC)/Traction Control
System (TCS) Button (If Equipped). SeeElectronic
Stability Control (ESC) on page 4-6orTraction
Control System (TCS) on page 4-8.
L.Driver Information Center (DIC) on page 3-34.
M.Horn on page 3-5.
N.Windshield Wipers on page 3-8andWindshield
Washer on page 3-9.
O.Climate Control System on page 3-16.P. Cigarette Lighter (If Equipped).Ashtray(s) and
Cigarette Lighter on page 3-15andAccessory Power
Outlet(s) on page 3-14(If Equipped).
Q. Shift Lever. SeeManual Transmission Operation on
page 2-22. SeeAutomatic Transmission Operation
on page 2-19(If equipped with automatic
transmission).
R.Parking Brake on page 2-23.
S.Audio System(s) on page 3-46.
T.Cupholders on page 2-33.
U. Trunk Release. SeeTrunk on page 2-8.
V.Glove Box on page 2-33.
Hazard Warning Flashers
|(Hazard Warning Flasher):Press this button
located on the instrument panel, to make the front and
rear turn signal lamps ash on and off. This warns
others that you are having trouble.
Press
|again to turn the ashers off.
Horn
To sound the horn, press the center pad on the steering
wheel.
3-5

Instrument Panel Brightness
The control for this feature is located on the instrument
panel to the right of the steering wheel.
DInstrument Panel Brightness:Turn the knob
clockwise or counterclockwise to brighten or dim
the lights.
Entry/Exit Lighting
The lamps inside the vehicle come on when any door is
opened. These lamps will fade out after about
20 seconds after all of the doors have been closed or
when the ignition is turned on. These lamps will also go
on when you press the trunk release, unlock symbol
button or the horn symbol on the Remote Keyless Entry
System (RKE) Transmitter.
The lamps inside the vehicle will stay on for about
20 seconds after the key is removed from the ignition to
provide an illuminated exit.
Mirror Reading Lamps
The vehicle has reading lamps on the rearview mirror.
Push the button to turn the reading lamps on and off.
Battery Run-Down Protection
The vehicle has a battery saver feature designed to
protect the vehicle’s battery.
When any interior lamp is left on and the ignition is
turned off, the battery rundown protection system
automatically turns the lamp off after 20 minutes. This
prevents draining of the battery.
Accessory Power Outlet(s)
The accessory power outlet can be used to connect
electrical equipment, such as a cellular phone.
The accessory power outlet is located on the instrument
panel, below the radio.
To use the outlet, remove the cover. When not in use,
always cover the outlet with the protective cap.
Notice:Leaving electrical equipment plugged in for
an extended period of time while the vehicle is off
will drain the battery. Power is always supplied
to the outlets. Always unplug electrical equipment
when not in use and do not plug in equipment
that exceeds the maximum 20 ampere rating.
3-14

TRACTION OFF
If your vehicle has the Traction Control System (TCS),
this message displays and the ESC/TCS light on
the instrument panel cluster comes on solid when the
TCS is turned off. Adjust your driving accordingly.
SeeTraction Control System (TCS) on page 4-8and
Electronic Stability Control (ESC)/Traction Control
System (TCS) Indicator/Warning Light on page 3-27for
more information.
TRUNK AJAR
This message displays when the trunk is not closed
completely. Make sure that the trunk is closed
completely. SeeTrunk on page 2-8andTrunk Ajar Light
on page 3-33.
DIC Vehicle Personalization
Your vehicle has personalization capabilities that allow
you to program certain features to a preferred setting.
All of the features listed may not be available on
your vehicle. Only the features available will be
displayed on the DIC.
The default settings for the features were set when your
vehicle left the factory, but may have been changed
from their default state since that time.To change feature settings, use the following procedure:
Entering Personalization Menu
1. Turn the ignition on while the vehicle is stopped.
To avoid excessive drain on the battery, it is
recommended that the headlamps are turned off.
2. Press and hold the information and reset buttons at
the same time for one second, then release to enter
the personalization menu.
If the vehicle speed is greater than 2 mph (3 km/h),
only the UNITS menu will be accessible.
3. Press the information button to scroll through the
available personalization menu modes.
Press the reset button to scroll through the available
settings for each mode.
If you do not make a selection within ten seconds,
the display will go back to the previous information
displayed.
Personalization Menu Modes
OIL LIFE RESET
When this feature is displayed, you can reset the engine
oil life system. To reset the system, seeEngine Oil
Life System on page 5-19. See “OIL LIFE” underDIC
Operation and Displays on page 3-35for more
information.
3-41

UNLOCK HORN
If your vehicle has Remote Keyless Entry (RKE), this
feature, which allows the vehicle’s horn to chirp on
the rst press of the unlock button on the RKE
transmitter, can be enabled or disabled. When UNLOCK
HORN appears on the display, press and hold the
reset button for at least one second to scroll through the
available settings:
OFF (default):The horn will not chirp when the unlock
button on the RKE transmitter is pressed.
ON:The horn will chirp on the rst press of the unlock
button on the RKE transmitter.
SeeRemote Keyless Entry (RKE) System Operation on
page 2-4for more information.
To select a setting and move on to the next feature,
press the information button while the desired setting is
displayed on the DIC.
LIGHT FLASH
If your vehicle has Remote Keyless Entry (RKE), this
feature, which allows the vehicle’s exterior hazard/turn
signal lighting to ash every time the lock, unlock,
or trunk release buttons on the RKE transmitter are
pressed, can be enabled or disabled. When LIGHT
FLASH appears on the display, press and hold the reset
button for at least one second to scroll through the
available settings:
OFF:The exterior hazard/turn signal lighting will not
ash when the lock, unlock, or trunk release buttons on
the RKE transmitter are pressed.
ON (default):The exterior hazard/turn signal lighting
will ash when the lock, unlock, or trunk release buttons
on the RKE transmitter are pressed.
SeeRemote Keyless Entry (RKE) System Operation on
page 2-4for more information.
To select a setting and move on to the next feature,
press the information button while the desired setting is
displayed on the DIC.
3-43

Front Turn Signal, Parking and
Fog Lamps
A. Front Turn Signal/
Parking Lamp
B. Fog Lamp (If Equipped)
To replace one of these bulbs:
1. Open the hood. SeeHood Release on page 5-11.
2. Locate the bulb assembly under the front bumper.
3. Turn the bulb socket counterclockwise and pull
out the bulb assembly.
4. Disconnect the bulb socket from the wiring harness.
5. Pull the old bulb straight out of the bulb socket.6. Push the new bulb straight into the bulb socket until
it connects.
7. Reconnect the bulb socket to the wiring harness.
8. Push the bulb socket straight into the bulb assembly
and turn it clockwise to lock it into place.
Taillamps, Turn Signal, and
Stoplamps (Base Level)
To replace one of these bulbs:
1. Open the trunk. SeeTrunk on page 2-8.
2. From inside the vehicle, remove the two screws
from the taillamp assembly.
3. Remove the taillamp assembly.
5-43