tow PONTIAC VIBE 2007 Workshop Manual

6. Remove all the wheel nuts and take off the
at tire.
7. Install the spare tire.
{CAUTION:
Rust or dirt on the wheel, or on the parts
to which it is fastened, can make the
wheel nuts become loose after time. The
wheel could come off and cause an
accident. When you change a wheel,
remove any rust or dirt from the places
where the wheel attaches to the vehicle. In
an emergency, you can use a cloth or a
paper towel to do this; but be sure to use
a scraper or wire brush later, if needed, to
get all the rust or dirt off.
348

10. Reinstall the wheel nuts with the rounded end
of the nuts toward the wheel. Tighten each nut
by hand until the wheel is held against the hub.
11. Lower the vehicle by turning the jack handle
counterclockwise. Lower the jack completely.
{CAUTION:
Incorrect wheel nuts or improperly
tightened wheel nuts can cause the wheel
to come loose and even come off. This
could lead to an accident. Be sure to use
the correct wheel nuts. If you have to
replace them, be sure to get new GM
original equipment wheel nuts. Stop
somewhere as soon as you can and have
the nuts tightened with a torque wrench to
the proper torque specication. See
Capacities and Specifications on page 369
for wheel nut torque specication.
350

Fabric/Carpet
Use a vacuum cleaner with a soft brush
attachment frequently to remove dust and loose
dirt. A canister vacuum with a beater bar in
the nozzle may only be used on oor carpet and
carpeted oor mats. For soils, always try to remove
them rst with plain water or club soda. Before
cleaning, gently remove as much of the soil
as possible using one of the following techniques:
For liquids: gently blot the remaining soil with a
paper towel. Allow the soil to absorb into the
paper towel until no more can be removed.
For solid dry soils: remove as much as possible
and then vacuum.
To clean, use the following instructions:
1. Saturate a lint-free, clean white cloth with
water or club soda.
2. Wring the cloth to remove excess moisture.
3. Start on the outside edge of the soil and gently
rub toward the center. Continue cleaning,
using a clean area of the cloth each time it
becomes soiled.
4. Continue to gently rub the soiled area until the
cleaning cloth remains clean.5. If the soil is not completely removed, use a
mild soap solution and repeat the cleaning
process that was used with plain water.
If any of the soil remains, a commercial fabric
cleaner or spot lifter may be necessary. When a
commercial upholstery cleaner or spot lifter is to be
used, test a small hidden area for colorfastness
rst. If the locally cleaned area gives any
impression that a ring formation may result, clean
the entire surface.
After the cleaning process has been completed, a
paper towel can be used to blot excess moisture
from the fabric or carpet.
Leather
A soft cloth dampened with water may be used to
remove dust. If a more thorough cleaning is
necessary, a soft cloth dampened with a mild soap
solution can be used. Allow the leather to dry
naturally. Do not use heat to dry. Never use steam
to clean leather. Never use spot lifters or spot
removers on leather. Many commercial leather
cleaners and coatings that are sold to preserve
and protect leather may permanently change
the appearance and feel of your leather and are
356

Weatherstrips
Silicone grease on weatherstrips will make them
last longer, seal better, and not stick or squeak.
Apply silicone grease with a clean cloth. During
very cold, damp weather frequent application may
be required.
Washing Your Vehicle
The paint nish on the vehicle provides beauty,
depth of color, gloss retention, and durability.
The best way to preserve the vehicle’s nish is to
keep it clean by washing it often with lukewarm
or cold water.
Do not wash the vehicle in the direct rays of the
sun. Use a car washing soap. Do not use
strong soaps or chemical detergents. Be sure to
rinse the vehicle well, removing all soap
residue completely. Approved cleaning products
can be obtained from your dealer. SeeVehicle
Care/Appearance Materials on page 362.Donot
use cleaning agents that are petroleum based,
or that contain acid or abrasives. All cleaning
agents should be ushed promptly and not allowed
to dry on the surface, or they could stain.Dry the nish with a soft, clean chamois or an
all-cotton towel to avoid surface scratches
and water spotting.
High pressure car washes may cause water to
enter the vehicle.
Cleaning Exterior Lamps/Lenses
Use only lukewarm or cold water, a soft cloth and
a car washing soap to clean exterior lamps
and lenses. Follow instructions underWashing
Your Vehicle on page 358.
Finish Care
Occasional waxing or mild polishing of the vehicle
by hand may be necessary to remove residue
from the paint nish. Approved cleaning products
can be obtained from your dealer. SeeVehicle
Care/Appearance Materials on page 362.
Notice:Machine compounding or aggressive
polishing on a basecoat/clearcoat paint
nish may damage it. Use only non-abrasive
waxes and polishes that are made for a
basecoat/clearcoat paint nish on your vehicle.
358

The vehicle has a basecoat/clearcoat paint nish.
The clearcoat gives more depth and gloss to
the colored basecoat. Always use waxes
and polishes that are non-abrasive and made for a
basecoat/clearcoat paint nish.
Foreign materials such as calcium chloride and
other salts, ice melting agents, road oil and
tar, tree sap, bird droppings, chemicals from
industrial chimneys, etc., can damage the vehicle’s
nish if they remain on painted surfaces. Wash
the vehicle as soon as possible. If necessary, use
non-abrasive cleaners that are marked safe for
painted surfaces to remove foreign matter.
Exterior painted surfaces are subject to aging,
weather, and chemical fallout that can take their
toll over a period of years. To help keep the
paint nish looking new, keep the vehicle in a
garage or covered whenever possible.
Windshield, Backglass, and Wiper
Blades
If the windshield is not clear after using the
windshield washer, or if the wiper blade chatters
when running, wax, sap or other material may
be on the blade or windshield.Clean the outside of the windshield with a
full-strength glass cleaning liquid. The windshield
is clean if beads do not form when you rinse it
with water.
Grime from the windshield will stick to the wiper
blades and affect their performance. Clean
the blade by wiping vigorously with a cloth soaked
in full-strength windshield washer solvent. Then
rinse the blade with water.
Check the wiper blades and clean them as
necessary; replace blades that look worn.
Aluminum Wheels
Notice:If you use strong soaps, chemicals,
abrasive polishes, cleaners, brushes, or
cleaners that contain acid on aluminum or
chrome-plated wheels, you could damage the
surface of the wheel(s). The repairs would
not be covered by your warranty. Use
only GM-approved cleaners on aluminum or
chrome-plated wheels.
Keep the wheels clean using a soft clean cloth
with mild soap and water. Rinse with clean water.
After rinsing thoroughly, dry with a soft clean
towel. A wax may then be applied.
359

❑Replace passenger compartment air lter.
❑Inspect fuel tank, cap, cap gasket, and lines for
damage or leaks (or every 24 months, whichever
occurs rst). Replace parts as needed.An
Emission Control Service. (See footnote †.)
❑Change manual transaxle uid every
30,000 miles (48 000 km) only if your vehicle
is used to tow a trailer.
35,000 Miles (56 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control
Service.
❑Rotate tires. SeeTire Inspection and Rotation on
page 333for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving
in dusty conditions. Replace lter if necessary.
40,000 Miles (64 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control
Service.
❑Rotate tires. SeeTire Inspection and Rotation on
page 333for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving
in dusty conditions. Replace lter if necessary.
45,000 Miles (72 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control
Service.
❑Rotate tires. SeeTire Inspection and Rotation on
page 333for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving
in dusty conditions. Replace lter if necessary.
❑Inspect passenger compartment air lter.
379

❑Inspect fuel tank, cap, cap gasket, and lines
for damage or leaks (or every 24 months,
whichever occurs rst). Replace parts
as needed.An Emission Control Service.
(See footnote †.)
❑Change manual transaxle uid every
30,000 miles (48 000 km) only if your vehicle
is used to tow a trailer.
❑Change automatic transaxle uid every
60,000 miles (96 000 km) if the vehicle is mainly
driven under one or more of these conditions:
In heavy city traffic where the outside
temperature regularly reaches 90°F
(32°C) or higher.
In hilly or mountainous terrain.
When doing frequent trailer towing.
Uses such as found in taxi, police, or
delivery service.
If you do not use your vehicle under any of these
conditions, the uid does not require changing.
See Part D: Recommended Fluids and Lubricants
on page 394for the proper uid to use.65,000 Miles 104 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control
Service.
❑Rotate tires. SeeTire Inspection and Rotation on
page 333for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving
in dusty conditions. Replace lter if necessary.
70,000 Miles (112 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control
Service.
❑Rotate tires. SeeTire Inspection and Rotation on
page 333for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving
in dusty conditions. Replace lter if necessary.
381

❑Inspect engine accessory drive belts
(or 12 months since last inspection).
An Emission Control Service.
❑Inspect fuel tank, cap, cap gasket, and lines for
damage or leaks (or every 24 months, whichever
occurs rst). Replace parts as needed.An
Emission Control Service. (See footnote †.)
❑Change manual transaxle uid every
30,000 miles (48 000 km) only if your
vehicle is used to tow a trailer.
95,000 Miles (152 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control
Service.
❑Rotate tires. SeeTire Inspection and Rotation on
page 333for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving
in dusty conditions. Replace lter if necessary.
100,000 Miles (160 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control
Service.
❑Rotate tires. SeeTire Inspection and Rotation on
page 333for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving
in dusty conditions. Replace lter if necessary.
105,000 Miles (168 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control
Service.
❑Rotate tires. SeeTire Inspection and Rotation on
page 333for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving
in dusty conditions. Replace lter if necessary.
❑Inspect passenger compartment air lter.
❑Inspect engine accessory drive belts (or every
48 months, whichever occurs rst). Visually
inspect belt for fraying, excessive cracks, or
obvious damage. Replace belt if necessary.
An Emission Control Service.
383

❑Inspect for tappet noise and engine vibration.
Adjust valve clearance to factory specications if
necessary (or every 48 months, whichever
occurs rst).An Emission Control Service.
❑Inspect fuel tank, cap, cap gasket, and lines for
damage or leaks (or every 24 months, whichever
occurs rst). Replace parts as needed.An
Emission Control Service. (See footnote †.)
❑Change manual transaxle uid every
30,000 miles (48 000 km) only if your vehicle is
used to tow a trailer.
❑Change automatic transaxle uid every
60,000 miles (96 000 km) if the vehicle is mainly
driven under one or more of these conditions:
In heavy city traffic where the outside
temperature regularly reaches 90°F
(32°C) or higher.
In hilly or mountainous terrain. When doing frequent trailer towing.
Uses such as found in taxi, police, or
delivery service.
If you do not use your vehicle under any of these
conditions, the uid does not require changing.
See Part D: Recommended Fluids and Lubricants
on page 394for the proper uid to use.
150,000 Miles (240 000 km)
❑Drain, ush, and rell the cooling system
(or every 5 years, whichever occurs rst). This
service can be complex; you should have
your dealer perform this service. SeeEngine
Coolant on page 294for what to use. Inspect
hoses. Clean radiator, condenser, pressure cap,
and neck. Pressure test cooling system and
pressure cap.An Emission Control Service.
385

Ignition Transaxle Lock Check
While parked, and with the parking brake set, try
to turn the ignition to LOCK in each shift lever
position.
With an automatic transaxle, the ignition
should turn to LOCK only when the shift lever
is in PARK (P).
With a manual transaxle, the ignition should
turn to LOCK only if you push the ignition
key in farther, while turning it toward LOCK.
Contact your GM Goodwrench
®dealer if service is
required.
Parking Brake and Automatic Transaxle
Park (P) Mechanism Check
{CAUTION:
When you are doing this check, your
vehicle could begin to move. You or
others could be injured and property
could be damaged. Make sure there is
room in front of your vehicle in case it
begins to roll. Be ready to apply the
regular brake at once should the vehicle
begin to move.
390