lock Ram 1500 2014 Owner's Manual

return to the previous menu. Refer to “Keyless Enter-N-
Go™” in “Things To Know Before Starting Your Vehicle”.
•Memory To FOB — If Equipped
This feature provides automatic driver seat positioning to
enhance driver mobility when entering and exiting the
vehicle. To make your selection, touch the Memory
Linked To FOB soft-key, until a check-mark appears next
to setting, showing that setting has been selected. Touch
the back arrow soft-key to return to the previous menu.
NOTE: The seat will return to the memorized seat
location (if Recall Memory with Remote Key Unlock is set
to ON) when the Remote Keyless Entry (RKE) transmitter
is used to unlock the door. Refer to “Driver Memory
Seat” in “Understanding The Features Of Your Vehicle”
for further information. Remote Start Comfort Systems — If Equipped
After pressing the “Auto-On Comfort & Remote Start”
button on the touchscreen the following settings will be
available:
•
Horn With Remote Start
When this feature is selected, the horn will sound when
the remote start is activated. To make your selection,
press the “Sound Horn With Remote Start” button on the
touchscreen, until a check-mark appears next to the
setting, showing that the setting has been selected. Press
the back arrow button on the touchscreen to return to the
previous menu.
• Auto-On Driver Heated/Ventilated Seat & Steering
Wheel With Vehicle Start — If Equipped
When this feature is selected the driver’s heated seat and
heated steering wheel will automatically turn on when
350 UNDERSTANDING YOUR INSTRUMENT PANEL

Front Blower Control
There are four blower speeds. Use this
control to regulate the amount of air
forced through the system in any
mode you select. The blower speed
increases as you move the control
clockwise from the OFF position.NOTE:
For vehicles equipped with Remote Start, the
climate controls will not function during Remote Start
operation if the blower control is left in the OFF position.
Temperature Control
Use this control to regulate the tem-
perature of the air inside the passenger
compartment. Rotating the knob coun-
terclockwise, from top center into the
blue area of the scale, indicates cooler
temperatures. Rotating the knob clock-
wise, into the red area, indicates
warmer temperatures.
362 UNDERSTANDING YOUR INSTRUMENT PANEL

Defrost Mode
Air is directed through the windshield and side
window demist outlets. Use the DEFROST mode
with maximum blower and warm temperature settings
for best windshield and side window defrosting.
NOTE: The air conditioning compressor operates in MIX
and DEFROST, or a blend of these modes even if the A/C
button is not pressed. This dehumidifies the air to help
dry the windshield. To improve fuel economy, use these
modes only when necessary.
Recirculation Control
Press the Recirculation Control button to
choose between outside air intake or recircula-
tion of the air inside the vehicle. A LED will
illuminate when you are in Recirculation
mode. Only use the Recirculation mode to temporarily block out any outside odors, smoke, or dust, and to cool
the interior rapidly upon initial start-up in very hot or
humid weather.
NOTE:
•
If the RECIRCULATION button is pressed when the
system is in Defrost mode, the Recirculation LED
indicator will flash three times and then turn off to
indicate Recirculation mode is not allowed.
• Continuous use of the Recirculation mode may make
the inside air stuffy and window fogging may occur.
Extended use of this mode is not recommended.
• In cold or damp weather, the use of the Recirculation
mode will cause windows to fog on the inside because
of moisture buildup inside the vehicle. For maximum
defogging, select the outside air position.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 365

NOTE:BI-LEVEL mode is designed under comfort con-
ditions to provide cooler air out of the panel outlets and
warmer air from the floor outlets.
• Floor Mode
Air comes from the floor outlets. A slight amount
of air is directed through the defrost and side
window demister outlets.
• Mix Mode
Air comes from the floor, defrost and side window
demister outlets. This mode works best in cold or
snowy conditions.
NOTE: The air conditioning compressor operates in MIX
and DEFROST modes even if the A/C button is not
pressed. This dehumidifies the air to help dry the wind-
shield. To improve fuel economy, utilize these modes
only when required. 7. Blower Control
Blower control is used to regulate the amount of air
forced through the climate system. There are seven
blower speeds available. Adjusting the blower will cause
automatic mode to switch to manual operation. The
speeds can be selected using either hard-keys or soft-keys
as follows:
Hard-Key
The blower speed increases as you turn the control
clockwise from the lowest blower setting. The blower
speed decreases as you turn the knob counterclockwise.
Soft-Key
Use the small blower icon to reduce the blower setting
and the large blower icon to increase the blower setting.
Blower can also be selected by pressing the blower bar
area between the icons.
370 UNDERSTANDING YOUR INSTRUMENT PANEL

7. Passenger Temperature Control Up Button
Provides the passenger with independent temperature
control. Push the hard-key button for warmer tempera-
ture settings or on the touchscreen, press and slide the
soft-key temperature bar towards the red arrow soft-key
for warmer temperature settings.
NOTE:Pressing this button while in Sync mode will
automatically exit Sync.
8. Passenger Temperature Control Down Button
Provides the passenger with independent temperature
control. Push the hard-key button for cooler temperature
settings or on the touchscreen, press and slide the soft-
key temperature bar towards the blue arrow soft-key for
cooler temperature settings.
NOTE: Pressing this button while in Sync mode will
automatically exit Sync. 9. SYNC
Press the Sync soft-key to toggle the Sync feature On/Off.
The Sync indicator is illuminated when this feature is
enabled. Sync is used to synchronize the passenger
temperature setting with the driver temperature setting.
Changing the passenger temperature setting while in
Sync will automatically exit this feature.
10. Blower Control
Blower control is used to regulate the amount of air
forced through the climate system. There are seven
blower speeds available. Adjusting the blower will cause
automatic mode to switch to manual operation. The
speeds can be selected using either hard-keys or soft-keys
as follows:
Hard-Key
The blower speed increases as you turn the control
clockwise from the lowest blower setting. The blower
speed decreases as you turn the knob counterclockwise.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 375

STARTING AND OPERATING
CONTENTS
STARTING PROCEDURES ................390
▫ Normal Starting ...................... .390
▫ Automatic Transmission ................391
▫ Keyless Enter-N-Go™ ..................391
▫ Normal Starting ...................... .391
▫ Extreme Cold Weather
(Below –20°F Or 29°C) ................393
▫ If Engine Fails To Start .................393
▫ After Starting ....................... .394
 STOP/START SYSTEM — IF EQUIPPED ......395▫
Automatic Mode ..................... .395
▫ Possible Reasons The Engine Does Not AUTO
STOP............................. .396
▫ To Start The Engine While In Autostop Mode . .396
▫ To Manually Turn Off The Stop Start System . .398
▫ To Manually Turn On The Stop Start System . .399
▫ System Malfunction ....................399
 ENGINE BLOCK HEATER — IF EQUIPPED . . .399
 AUTOMATIC TRANSMISSION ............400
▫ Key Ignition Park Interlock ...............402
5

▫Brake/Transmission Shift Interlock System . . .403
▫ Eight-Speed Automatic Transmission — If
Equipped .......................... .403
▫ Six-Speed Automatic Transmission — 1500 Models
Only (If Equipped) ....................412
▫ Six-Speed Automatic Transmission — 2500/3500
Models Only ....................... .425
 FOUR-WHEEL DRIVE OPERATION — IF
EQUIPPED .......................... .436
▫
Manually Shifted Transfer Case — If Equipped . .436
▫ Electronically Shifted Transfer Case (Four-Position
Switch) — If Equipped .................440
▫ Electronically Shifted Transfer Case (Five-Position
Switch) — If Equipped .................447 ▫
Electronically Shifted Transfer Case (Five-Position
Switch) — If Equipped .................452
 AIR SUSPENSION SYSTEM (1500 MODELS ONLY)
— IF EQUIPPED ...................... .459
▫ Description ......................... .459
▫ Air Suspension Modes ..................463
▫ Electronic Vehicle Information Center (EVIC)
Display Messages .....................464
▫ Operation .......................... .464
 AIR SUSPENSION SYSTEM (2500/3500 MODELS
ONLY) — IF EQUIPPED ..................466
▫ Description ......................... .466
▫ Air Suspension Modes ..................467
▫ Electronic Vehicle Information Center (EVIC)
Display Messages .....................469
384 STARTING AND OPERATING

▫Operation .......................... .469
 AXLE LOCKER SYSTEM — POWER WAGON
MODELS ONLY (IF EQUIPPED) ............469
 STABILIZER/SWAY BAR SYSTEM — POWER
WAGON ONLY ....................... .472
 SAFE OFF-ROAD DRIVING — POWER WAGON
ONLY.............................. .474
▫ Off-Road Driving Tips And Vehicle
Characteristics ...................... .474
▫ Driving In Snow, Mud And Sand ..........477
▫ Crossing Obstacles (Rocks And Other High
Points) ............................ .478
▫ Hill Climbing ....................... .481
▫ Driving Through Water .................484
▫ Airing Down For Off-Road Driving .........487▫
Vehicle Recovery ..................... .487
▫ After Driving Off-Road .................491
 LIMITED-SLIP DIFFERENTIAL .............492
 DRIVING ON SLIPPERY SURFACES .........493
▫ Acceleration ........................ .493
▫ Traction ........................... .494
 DRIVING THROUGH WATER .............494
▫ Flowing/Rising Water ..................494
▫ Shallow Standing Water .................495
 OFF-ROAD DRIVING TIPS ...............496
▫ After Driving Off-Road .................497
 WINCH USAGE — POWER WAGON ONLY — (IF
EQUIPPED) ......................... .498
5
STARTING AND OPERATING 385

▫Things To Know Before Using Your Winch . . . .498
▫ Understanding The Features Of Your Winch . . .501
▫ Winch Accessories ....................503
▫ Operating Your Winch ..................504
▫ Rigging Techniques ....................516
 POWER STEERING — 1500 MODELS ........518
 POWER STEERING — 2500/3500 MODELS . . . .519
▫ Power Steering Fluid
Check — 2500/3500 Models .............520
 FUEL SAVER TECHNOLOGY 5.7L/6.4L ENGINES
ONLY — IF EQUIPPED ..................521
 PARKING BRAKE ..................... .521
 BRAKE SYSTEM ...................... .524
▫ Four-Wheel Anti-Lock Brake System ........524▫
Hydraulic Brake Assist — 2500/3500 Models Only
(Except Power Wagon) ..................526
 ELECTRONIC BRAKE CONTROL SYSTEM . . . .526
▫ Anti-Lock Brake System (ABS) ............527
▫
Traction Control System (TCS) — If Equipped . .527
▫ Brake Assist System (BAS) — If Equipped . . . .528
▫ Hill Start Assist (HSA) — If Equipped .......529
▫ Electronic Stability Control
(ESC) — If Equipped ..................532
▫ ESC Activation/Malfunction Indicator Light And
ESC OFF Indicator Light ................536
▫ Trailer Sway Control (TSC) — If Equipped . . .538
 TIRE SAFETY INFORMATION .............539
▫ Tire Markings ....................... .539
386 STARTING AND OPERATING

STARTING PROCEDURES
Before starting your vehicle, adjust your seat, adjust both
inside and outside mirrors, and fasten your seat belt.
The starter should not be operated for more than 15-
second intervals. Waiting a few seconds between such
intervals will protect the starter from overheating.
WARNING!
Never leave children alone in a vehicle, or with
access to an unlocked vehicle. Leaving children in a
vehicle unattended is dangerous for a number of
reasons. A child or others could be seriously or
fatally injured. Children should be warned not to
touch the parking brake, brake pedal or the shift
lever. Do not leave the Key Fob in or near the vehicle,
or in a location accessible to children, and do not
(Continued)
WARNING!(Continued)
leave the ignition of a vehicle equipped with keyless
Enter-N-Go in the ACC or ON/RUN mode. A child
could operate power windows, other controls, or
move the vehicle.
Normal Starting
Normal starting of either a warm or cold engine is
obtained without pumping or pressing the accelerator
pedal. Cycle the ignition to the START position and
release when the engine starts. If the engine fails to start
within 10 seconds, cycle the ignition to the OFF position,
wait five seconds, then repeat the “Normal Starting”
procedure.
390 STARTING AND OPERATING