instrument panel Ram ProMaster 2017 Owner's Manual

If tire pressure is less than 19 psi (1.3 Bar):
The tire is too badly damaged. Do not attempt to drive the
vehicle further. Call for assistance.
If the tire pressure is 19 psi (1.3 Bar) or higher:
1. Push the Power Button (4) to turn on Tire Service Kitand inflate the tire to the pressure indicated on the tire
and loading information label on the driver-side door
opening.
NOTE: If the tire becomes over-inflated, push the Deflation
Button to reduce the tire pressure to the recommended
inflation pressure before continuing.
2. Disconnect the Tire Service Kit from the valve stem, reinstall the cap on the valve stem and unplug from
12 Volt outlet.
3. Place the Tire Service Kit in its proper storage area in the vehicle.
4. Have the tire inspected and repaired or replaced at the earliest opportunity at an Authorized Dealer or tire
service center.
5. Remove the Speed Limit sticker from the instrument panel after the tire has been repaired. 6. Replace the Sealant Bottle (1) and Sealant Hose (6)
assembly at your Authorized Dealer as soon as possible.
Refer to (F) “Sealant Bottle and Hose Replacement”.
NOTE: When having the tire serviced, advise the Autho-
rized Dealer or service center that the tire has been sealed
using the Tire Service Kit.
(F) Sealant Bottle And Hose Replacement:
1. Uncoil the Sealant Hose (6) (clear in color).
2. Locate the round Sealant Bottle release button in the recessed area under the sealant bottle.
3. Push the Sealant Bottle release button. The Sealant Bottle (1) will pop up. Remove the bottle and dispose of it
accordingly.
4. Clean any remaining sealant from the Tire Service Kit housing.
5. Position the new Sealant Bottle (1) in the housing so that the Sealant Hose (6) aligns with the hose slot in the front
of the housing. Push the bottle into the housing. An
audible click will be heard indicating the bottle is locked
into place.6
WHAT TO DO IN EMERGENCIES 251

MAINTAINING YOUR VEHICLE
CONTENTS
ENGINE COMPARTMENT — 3.6L ...........277
 ONBOARD DIAGNOSTIC SYSTEM — OBD II . . .278
▫ Onboard Diagnostic System (OBD II)
Cybersecurity ........................ .278
▫ Loose Fuel Filler Cap Message .............279
 EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS .......................... .279
 REPLACEMENT PARTS ...................280
 DEALER SERVICE ...................... .280
 MAINTENANCE PROCEDURES .............281
▫ Engine Oil .......................... .281
▫ Engine Oil Filter ...................... .283
▫ Engine Air Cleaner Filter .................284
▫ Exhaust System ....................... .284
▫ Maintenance-Free Battery .................286 ▫
Air Conditioner Maintenance ..............286
▫ Body Lubrication ..................... .289
▫ Windshield Wiper Blades .................289
▫ Cooling System ....................... .290
▫ Brake System ........................ .294
▫ Automatic Transmission (3.6L Gasoline Engine
Only) .............................. .295
▫ Appearance Care And Protection From
Corrosion ........................... .297
▫ Cleaning The Instrument Panel Cupholders . . . .301
 FUSES ............................... .302
▫ Underhood Fuses ...................... .302
▫ Interior Fuses ......................... .307
▫ Right Central Pillar Fuses .................310
 VEHICLE
STORAGE.....................311
7

WARNING!(Continued)
vehicle control could occur that may result in an
accident involving serious injury or death.
• Access, or allow others to access, information
stored in your vehicle systems, including personal
information.
For further information, refer to “Cybersecurity” in the
“Understanding Your Instrument Panel” section.
Loose Fuel Filler Cap Message
If the vehicle diagnostic system determines that the fuel
filler cap is loose, improperly installed, or damaged, a
“Check fuel cap” message will be displayed in the instru-
ment cluster display. Refer to “Instrument Cluster Display”
in ”Understanding Your Instrument Panel” for further
information. Tighten the gas cap until a clickingsound is
heard. This is an indication that the gas cap is properly
tightened.
Push the odometer reset button to turn the message off. If
the problem persists, the message will appear the next time
the vehicle is started. This might indicate a damaged cap. If
the problem is detected twice in a row, the system will turn
on the MIL. Resolving the problem will turn the MIL light
off.
EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS
In some localities, it may be a legal requirement to pass an
inspection of your vehicle’s emissions control system.
Failure to pass could prevent vehicle registration.
For states that require an Inspection and Mainte-
nance (I/M), this check verifies the “Malfunction
Indicator Light (MIL)” is functioning and is not on
when the engine is running, and that the OBD II system is
ready for testing.
Normally, the OBD II system will be ready. The OBD II
system may notbe ready if your vehicle was recently
serviced, recently had a dead battery or a battery replace-
ment. If the OBD II system should be determined not ready
for the I/M test, your vehicle may fail the test.
Your vehicle has a simple ignition actuated test, which you
can use prior to going to the test station. To check if your
vehicle’s OBD II system is ready, you must do the following:
1. Cycle the ignition switch to the ON position, but do not crank or start the engine.
NOTE: If you crank or start the engine, you will have to
start this test over.
7
MAINTAINING YOUR VEHICLE 279

When cleaning the rear view mirror, spray cleaner on the
towel or cloth that you are using. Do not spray cleaner
directly on the mirror.
Cleaning Plastic Instrument Cluster Lenses
The lenses in front of the instruments in this vehicle are
molded in clear plastic. When cleaning the lenses, care
must be taken to avoid scratching the plastic.
1. Clean with a wet soft cloth. A mild soap solution may beused, but do not use high alcohol content or abrasive
cleaners. If soap is used, wipe clean with a clean damp
cloth.
2. Dry with a soft cloth.
Seat Belt Maintenance
Do not bleach, dye, or clean the belts with chemical
solvents or abrasive cleaners. This will weaken the fabric.
Sun damage can also weaken the fabric.
If the belts need cleaning, use MOPAR Total Clean, a mild
soap solution, or lukewarm water. Do not remove the belts
from the vehicle to wash them. Dry with a soft cloth.
Replace the belts if they appear frayed or worn or if the
buckles do not work properly.
WARNING!
A frayed or torn belt could rip apart in a collision and
leave you with no protection. Inspect the belt system
periodically, checking for cuts, frays, or loose parts.
Damaged parts must be replaced immediately. Do not
disassemble or modify the system. Seat belt assemblies
must be replaced after a collision if they have been
damaged (i.e., bent retractor, torn webbing, etc.).
Cleaning The Instrument Panel Cupholders
Removal
Pull the flexible liner from the cupholder drawer starting at
one edge to ease removal.
Cleaning
The liner is top shelf dishwasher safe, or you may follow
the cleaning procedure below.
Soak the liner in a mixture of medium hot tap water and
one teaspoon of mild liquid dish soap. Let soak for
approximately 30 minutes. After 30 minutes, pull the liner
from the water and dip it back into the water about six
times. This will loosen any remaining debris. Rinse the
7
MAINTAINING YOUR VEHICLE 301

CavityMini Fuse Description
F62 30 Amp Green Transmission Power RELE (3.6 Gasoline Engine) — If
Equipped
F64 7.5 Amp Brown Urea Pump (3.0 Diesel Engine) — If Equipped
F65 25 Amp White Urea NOX Sensor 1–2 — PM Sensor (3.0 Diesel Engine)
— If Equipped
F66 5 Amp Beige Shifter Transmission Module (STM) (3.6 Gasoline Engine)
— If Equipped
Interior Fuses
The interior fuse panel is part of the Body Control Module
(BCM) and is located on the driver’s side under the
instrument panel.
Fuse Panel
7
MAINTAINING YOUR VEHICLE 307

MAINTENANCE SCHEDULE
Your vehicle is equipped with an automatic oil change
indicator system. The oil change indicator system will
remind you that it is time to take your vehicle in for
scheduled maintenance.
Based on engine operation conditions, the oil change
indicator message will illuminate in the instrument cluster.
This means that service is required for your vehicle.
Operating conditions such as frequent short-trips, trailer
tow, and extremely hot or cold ambient temperatures will
influence when the “Oil Change Required” message is
displayed. Severe Operating Conditions can cause the
change oil message to illuminate as early as 3,500 miles
(5,600 km) since last reset. Have your vehicle serviced as
soon as possible, within the next 500 miles (805 km).Your authorized dealer will reset the oil change indicator
message after completing the scheduled oil change. If a
scheduled oil change is performed by someone other than
your authorized dealer, the message can be reset by
referring to the steps described under “Instrument Cluster
Display” in “Understanding Your Instrument Panel” for
further information.
NOTE:
Under no circumstances should oil change inter-
vals exceed 10,000 miles (16,000 km), twelve months or 350
hours of engine run time, whichever comes first. The 350
hours of engine run or idle time is generally only a concern
for fleet customers.
Severe Duty All Models
Change Engine Oil at 4,000 miles (6,500 km) if the vehicle
is operated in a dusty and off road environment or is
operated predominately at idle or only very low engine
RPM’s. This type of vehicle use is considered Severe Duty.
320 MAINTENANCE SCHEDULES

Tank Capacity.......................... .315
Fueling ................................. .227
Fuses .................................. .302
Gas Cap (Fuel Filler Cap) ..............227, 228, 279
Gasoline, Clean Air ........................ .223
Gasoline (Fuel) ........................... .223
Gasoline, Reformulated ..................... .223
Gear Ranges ............................. .180
Gear Select Lever Override ....................272
General Information .....................157, 222
Glass Cleaning ........................... .300
Gross Axle Weight Rating .................229, 231
Gross Vehicle Weight Rating ...............229, 230
Guide, Body Builders .........................6
GVWR ................................. .229
Hazard Driving Through Flowing, Rising, Or Shallow
Standing Water ......................... .187
Hazard Warning Flasher ..................... .242
Headlights Cleaning .............................. .300
High Beam ..............................76
High Beam/Low Beam Select Switch ...........76Passing
................................76
Switch .................................74
Head Restraints ............................69
Heated Mirrors .............................59
Heated Seats ...............................68
Heater, Engine Block ....................... .177
High Beam/Low Beam Select (Dimmer) Switch ......76
Hill Start Assist ........................... .197
Hitches Trailer Towing .......................... .232
Hood Release ..............................72
Ignition ..................................11
Key ...................................11
Ignition Key Removal ........................11
Illuminated Entry ...........................14
Immobilizer (Sentry Key) ......................12
Inside Rearview Mirror .......................58
Instrument Cluster ..................... .100, 118
Instrument Cluster Display Instrument Cluster Display ..................120
Instrument Panel And Controls .................
99
Instrument Panel Lens Cleaning ................301
Interior Appearance Care .....................299
Intermittent Wipers (Delay Wipers) ...............80
338 INDEX