ignition RENAULT CLIO 2000 X65 / 2.G Owner's Manual

1
2
1


       
X65 - CLIOC:\Documentum\Checkout_47\Nu607-8gb_T1.WIN 12/10/2000 16:22-page68
1.60
REAR SCREEN WASH/WIPE
Intermittent rear wiper
Ignition on, turn the end of
stalk1to align reference mark2
opposite the symbol.
Rear washer
Ignition on, turn the end of
stalk1to align reference mark2
opposite the symbol.
When the stalk is released, it returns
to the rear wiper position.
Special note
For certain vehicles, if the windscreen
wipers are operating when reverse
gear is selected, the rear wiper will
operate intermittently.In freezing conditions, make sure that
the wiper blades are not stuck to the
windscreen (risk of overheating the
motor).
Keep an eye on the condition of the
blades. Change them as soon as they
become less efficient: approximately
once a year.


       
X65 - CLIOC:\Documentum\Checkout_47\Nu607-8gb_T1.WIN 12/10/2000 16:22-page72
1.64
FUEL TANK(continued)
Filling with fuel
Petrol version
Useunleaded fuel only.
Using leaded fuel will damage the
depollution equipment and may
lead to a loss of warranty.
To avoid the tank being filled with
leaded fuel, the filler neck has a
restrictor with a valvewhich only
allows an unleaded petrol nozzle to
be used(at the petrol pump).
- Insert the nozzle to open the valve,
asfarasitwillgo.
- Hold the nozzle in this position
while the tank is filled and then
release it.
Filling with fuel (continued)
Petrol and diesel versions
To allow room for expansion in the
fuel tank, do not top up more than
twice after the pump nozzle has cut
out automatically.
Any operation or
modification on the fuel
supply system (computers,
wiring, fuel circuit, in-
jector, protective covers...) is
strictly forbidden due to the
safety risks it may cause (except
for qualified staff from the
Renault network.
Persistent fuel odour
Your vehicle has a pressurised fuel
supply system. If a persistent fuel
odour should occur, please:
• stop the vehicle if traffic
conditions allow and switch the
ignition off;
• switch on the hazard warning
lights and ask all passengers to
leave the vehicle to keep them
away from the traffic;
• do not intervene or restart before
the vehicle has been checked by
qualified Renault network staff.

18IUB*DT[G      3DJH 
X65 - CLIOC:\Documentum\Checkout\Nu607-8gb_T2.WIN 30/9/2000 11:03-page1
2.01
Section 2: Driving
(advice on use relating to fuel economy and the environment)
Running in - Ignition switch ........................................................................................................................... 2.02
Starting and stopping the engine .................................................................................................................... 2.03
Special notes on petrol versions ..................................................................................................................... 2.04
Special notes on diesel versions ..................................................................................................................... 2.05
Advice on anti-pollution and how to economise on fuel ................................................................ 2.06
¬2.08
Environment ...................................................................................................................................................... 2.09
Proactive automatic gearbox ............................................................................................................... 2.10
¬2.12
Power-assisted steering .................................................................................................................................... 2.13
Handbrake - Gear lever .................................................................................................................................... 2.13
Anti-lock braking system ................................................................................................................................. 2.14

18IUB*DT[G      3DJH 
X65 - CLIOC:\Documentum\Checkout\Nu607-8gb_T2.WIN 30/9/2000 11:03-page2
2.02
RUNNING IN IGNITION SWITCH
Petrol version
For the first625 miles(1,000 km), do
not exceed 80 mph (130 km/h) in the
highest gear or 3,000 to 3,500 rpm.
After 625 miles(1,000 km), you may
drive your car normally, but it is
only after 1,500 miles (3,000 km)
have been covered that you may
reasonably expect full performance.
Service intervals:refer to the vehicle’s
Warranty and Servicing booklet.
Diesel version
For the first750 miles(1,500 km), do
not exceed 2,500 rpm. On completion
of this mileage you may drive faster,
but the vehicle will only provide top
performance after approximately
4,000 miles (6,000 km).
During the running in period, do not
accelerate hard while the engine is
still cold and do not let the engine
rev too high.
Service intervals:refer to the vehicle’s
Warranty and Servicing booklet.“Stop” position and anti-theft lock
applied St
To lock, remove the key and turn the
steering wheel until the latch clicks
as it engages in the steering column.
To unlock, turn the key and steering
wheel slightly.
“Accessories” position A
The ignition is switched off. Any
accessories (radio...) will continue
to function.“Ignition on” position M
The ignition is on:
• petrol version:the engine may be
started
• diesel version:the heater plugs
are on.
“Start” position D
If the engine does not start, turn the
key back before activating the starter
motor again. Release the key as soon
as the engine starts.

18IUB*DT[G      3DJH 
X65 - CLIOC:\Documentum\Checkout\Nu607-8gb_T2.WIN 30/9/2000 11:03-page3
2.03
STARTING AND STOPPING THE ENGINE
Starting the engine
OVehicles with an automatic
transmission
Refer to the paragraph
“Automatic transmission” in
section 2.
Vehicles with an immobiliser
system
In very cold conditions
(temperature below than –20°C):
so that it is easier to start the
engine, switch on the ignition for
several secondsbeforestarting
the engine.
Ensure the immobiliser system is
not operational. Refer to section
1 “immobiliser system”.
OPetrol injection
Engine cold or hot
- Turn the key to the start
positionwithout accelerating
- Release the key as soon as the
engine starts.
ODiesel injection
Engine cold or warm
Turn the key to the “Ignition on”
positionMand hold it there until
the preheating warning light
extinguishes (the colder the
engine, the more preheating is
required).
Turn the key to the “Start”
positionDand hold it there for
periods of a maximum of 10
seconds, until the engine starts.
In cold weather (below –10°C)
press down the clutch pedal and
accelerate fully while activating
the starter. After releasing the
key, when the engine has gained
speed, lift your foot off the
accelerator to let the engine
return to idling speed. Allow the
engine to idle for a few seconds
before removing your foot from
the clutch pedal.Hot engine
Turn the key directly to the “Start”
position. If the engine does not start
first time, repeat the operation using
preheating.
Do not allow the engine to race; let it
idle for a few moments.
Stopping the engine
With the engine idling, return the
key to the “Stop” position.
If there is a child (or animal) in the car, never leave it unattended with the key in the ignition. With the key in
the ignition it would be possible to operate the electrical equipment such as the windows and there is a risk
that the child may be seriously injured (by trapping his or her neck, arm, hand, etc.).
Never switch off the ignition before the vehicle has stopped completely.Once the engine has stopped, the power
steering, brake servo and passive safety devices such as air bags and pretensioners will no longer operate. When the
key has been removed, the steering will lock.

18IUB*DT[G      3DJH 
X65 - CLIOC:\Documentum\Checkout\Nu607-8gb_T2.WIN 30/9/2000 11:03-page4
2.04
SPECIAL POINTS - PETROL VERSIONS
The following operating conditions
may cause the catalytic converter to
overheat and thus reduce its
efficiencyor even destroy it and
cause heat damage to the vehicle:
• Driving for a long time with the
low fuel level warning light
illuminated;
• Faulty ignition, running out of
fuel or spark plug disconnected
occurring as engine misfiring and
snatches when driving;
• Using leaded petrol;
• Using lubrication additives or
fuel which is not approved by
Renault;
• Loss of power;
• The fitting of non-recognised
security systems which have been
integrated into the fuel injection
system for immobilisation
purposes;
Bump starting the vehicle, as
unburnt petrol in the system, may
affect the catalyst if the car does not
start quickly. However, jump
starting with jump leads across the
battery is permissible;If you note any of the above faults,
have the necessary repairs carried
out as soon as possible by your
Renault Dealer.
These faults may be avoided by
taking your vehicle regularly to
your Renault Dealer at the intervals
specifiedinyour“Warrantyand
Servicing” booklet.
Starting problems
To avoid damaging the catalytic
converter,do not keep tryingto start
the engine (using the starter, or by
pushing or pulling the vehicle)
without having identified and
corrected the cause of the fault.
If the fault cannot be found, do not
try to start the engine again, but call
for the assistance of a Renault
Dealer.
Never park the vehicle or
run the engine in locations
where combustible
substances or materials
such as grass or leaves may come
into contact with a hot exhaust
system.

18IUB*DT[G      3DJH 
X65 - CLIOC:\Documentum\Checkout\Nu607-8gb_T2.WIN 30/9/2000 11:03-page6
2.06
ADVICE ON ANTIPOLLUTION AND HOW TO ECONOMISE ON FUEL WHEN DRIVING
RENAULT actively participates in
the reduction of pollutant exhaust
gas emissions and in saving energy.
By virtue of its design, its original
settings and moderate fuel
consumption, your RENAULT
conforms to the current antipollution
standards. Technical design cannot
achieve everything, however. The
level of exhaust gas pollutant
emissions and the fuel
consumption of your vehicle is
within your control. Ensure that
your vehicle is maintained
correctly, and that you drive and use
it carefully.Maintenance
Not observing the antipollution
legislation may lead to the owner of
the vehicle being prosecuted.
Replacing parts of the engine, the
fuel supply system and the exhaust
with parts which are not original
parts recommended by the
manufacturer may mean that your
vehicle no longer conforms to the
antipollution regulations.
Have your vehicle checked and
adjusted by your Renault Dealer in
accordance with the instructions in
your Warranty and Servicing booklet.
Your Renault Dealer has all the
equipment necessary to ensure that
your vehicle is maintained to its
original standard.
Always remember that the emission
of pollutant fumes is directly linked
to fuel consumption.
Engine adjustments
• ignition:this requires no adjustment
• spark plugs:optimum conditions
of use, performance and output
require that the specifications
laid down by our Design
Department be rigorously
adhered to.
If the spark plugs have to be
replaced, use the make, type and
gap specified for your engine.
Consult your Renault Dealer for
this information.
• idle speed:this requires no
adjustment.
• air filter, diesel fuel filter:a
blocked cartridge reduces output
and must be replaced.
• injection pump setting:this must
be set to the recommended values.

18IUB*DT[G      3DJH 
X65 - CLIOC:\Documentum\Checkout\Nu607-8gb_T2.WIN 30/9/2000 11:03-page7
2.07
ADVICE ON ANTIPOLLUTION AND HOW TO ECONOMISE ON FUEL WHEN DRIVING(continued)
Monitoring exhaust gas
The exhaust gas monitoring system
will detect any malfunctioning of
the vehicle’s exhaust gas
depollution system.
If this system malfunctions, toxic
substances may be released into the
atmosphere or mechanical damage
may occur.
This warning light on the
instrument panel will
indicate if there are any
problems with the system.
It illuminates when the ignition is
switched on and extinguishes
within 3 seconds.
- If it illuminates continuously,
consult your Renault Dealer as
soon as possible.
- If it flashes, reduce the engine
speed until the light stops
flashing. Consult your Renault
Dealer as soon as possible.
Driving
•Drive carefully for the first few
miles until the engine reaches its
normal operating temperature
rather than letting it warm up
while stationary.
• Speed is expensive.
• “Snappy” driving uses a lot of
fuel: drive with a “light right
foot”.• Brake as little as possible by
suitably anticipating an obstacle
or bend and then simply releasing
the accelerator pedal.
• Avoid sudden acceleration.
• Do not overrev the engine in
intermediate gears.
Use the highest gear possible
without labouring the engine.
(On versions with an automatic
transmission, try to always use
positionD.)
• Try not to maintain the same
speed up a hill as you would on
the level; keep your foot in the
same position on the accelerator
pedal.
• Double declutching and
accelerating before switching off
the engine are superfluous
actions in modern cars.
• Bad weather, flooded roads
Do not drive on flooded
roads if the depth of
water is above the lower
edge of the wheel rims.

A
B
C
E
F
G
H
18IUB*DT[G      3DJH 
X65 - CLIOC:\Documentum\Checkout\Nu607-8gb_T2.WIN 30/9/2000 11:04-page10
2.10
PROACTIVE AUTOMATIC TRANSMISSION
Selector lever
The displayEand tell-tale lightsF,
G,Hon the instrument panel
indicate the position of the gear
lever1and/or the operating mode of
the automatic transmission.
P: Park
R: Reverse
N: Neutral
D: Drive in automatic
(gears authorised: 1, 2, 3 and 4)
2: 2nd gear hold
(gears authorised: 1, 2)
1: 1st gear holdPosition D3 or 3rd gear hold
(Gears authorised: 1, 2, 3).
With the selector lever in position
D, press buttonB. A tell-tale lightH
will illuminate on the instrument
panel. Press buttonBagain to
deselect this position. (The tell-tale
light will extinguish.)
Note:When the tell-tale light is
illuminated, the system will
prevent 4th gear being selected.For safety reasons, certain positions
may not be selected until the
mechanism is released: press buttonA.
The lever may only be moved to D
or R when the vehicle is stationary,
with your foot on the brake and the
accelerator pedal released.
Moving off forwards
With the lever in position PorN,
switch on the ignition.
With your foot on the brake pedal,
move the lever out of positionPorN.
For safety reasons, to take the lever
out of position P, the brake pedal
must be pressed before pressing the
releasing buttonA.

1
2
18IUB*DT[G      3DJH 
X65 - CLIOC:\Documentum\Checkout\Nu607-8gb_T2.WIN 30/9/2000 11:04-page13
2.13
GEAR LEVER HANDBRAKEPOWER ASSISTED STEERING
To select reverse
(vehicle stationary)
Move the lever to neutral, then lift
up ring1against the gear lever knob
to select reverse gear.
The reversing lights illuminate as
soon as reverse gear is selected
(ignition on).
To release
Pull the lever up slightly, press in
button2and lower the lever to the
floor.
If you are driving with the
handbrake incorrectly released, the
red warning light on the instrument
panel will remain illuminated.
To apply
Pull the lever upwards.
The lever should travel about 10
notches to hold the vehicle. Your
vehicle has self adjusting rear brake
shoes and the handbrake should
only be adjusted during a brake
overhaul.
When the vehicle is
stationary, make sure
that the handbrake is
properly applied so that
the vehicle does not move
unintentionally.
Make sure the handbrake is
properly released when driving,
otherwise overheating may
occur.Never leave the steering on full lock
when the vehicle is parked (risk of
damaging the power assisted
steering pump).
Never switch off the
engine when travelling
downhill, and avoid
doing so when driving in
general (power steering and
brake servo will not function).