RENAULT GRAND SCENIC 2016 J95 / 3.G Owners Manual

3.31
REAR SEAT OPERATION: 7-seater version (2/2)
Accessing the third row rear
seats
– Via the rear doors, push the second row seat forwards;
– lower the seat headrest;
– lift handle 3; the seatback lowers
itself. Fold the seat down;
– sit in the third row rear seat; – pull the second row rear seat to put it
into the table position;
– lift the seatback.
Use restriction
It is not permitted to drive with a second
row rear seatback or seat folded down
when there is a passenger occupying a
third row rear seat.
The label located on the back of the
seats reminds you of this.
3

3.32
TAILGATE
13
To open
Press button 1 and lift the tailgate.
To close
Lower the tailgate using the handles 2
inside the tailgate to help you.
Opening the doors manually
from the inside
Special note
If it is impossible to unlock the tailgate,
it can be done manually from inside:
– access the luggage compartment by tilting the rear bench seatback(s),
– insert a pencil or similar object in recess 3 and slide the unit as shown
in the illustration;
– push the tailgate to open it.
2

3.33
Rear parcel shelf
To remove, unhook the two straps 1.
Fold section A onto section B, then pull
up and towards you.
To refit it, proceed in reverse order to
removal.
REAR PARCEL SHELF: normal chassis versions
1
Maximum load on the rear parcel
shelf: 25 kg evenly distributed.
Do not place any objects,
especially heavy or hard
objects, on the parcel shelf.
These may pose a risk to
the vehicle occupants if the driver
has to brake suddenly or if the vehi-
cle is involved in an accident.
A
B

3.34
Removing the luggage cover
Push the luggage cover to the right
(movement A) and lift the left-hand side
of the inertia reel (movement B).
To refit the luggage cover, insert the
right-hand side, then push it to the right
(movement A ) and lower the left-hand
side of the inertia reel into its housing.
To remove the flexible
section of the luggage cover
Using handle 1, pull it gently to release
the pins from their mounting points lo-
cated on each side of the luggage com-
partment.
Guide the luggage cover onto the roller.
Luggage compartment cover
storage
Housing 3 in the luggage compartment
is designed for storing the luggage
cover.
To open the cover of housing 3, lift the
rings 2.
Insert the left-hand side of the inertia
reel into the storage compartment, fol-
lowed by the right-hand side. Position
the luggage cover so that it does not
extend beyond the storage compart-
ment.
To lock the cover of housing 3, lower
the rings 2.
LUGGAGE COVER: long chassis versions
Do not place any heavy or solid objects on the luggage cover. These may
pose a risk to the vehicle occupants if the driver has to brake suddenly\
or
if the vehicle is involved in an accident.
1B
A
32
2

3.35
Side storage compartments 1
Depending on the vehicle, this may be
used to hold oil containers etc.
Bag hooks 2
Maximum weight per hook: 5 kg.
LUGGAGE COMPARTMENT STORAGE SPACE AND FITTINGS (1/2)
Storage compartment under
luggage compartment
carpet 3
Depending on the vehicle, to access
this, lift the luggage compartment
carpet.
2
31

3.36
Always place objects being trans-
ported so that the heaviest items
are resting against the back of the
rear bench seat.
Separating the luggage
compartment
(depending on the vehicle)
The loading area can be separated.
Lift divider 4.
The elastic band 5 on the back is used
to hold objects vertically.
Maximum weight: 30 kg, evenly distrib-
uted.
4
LUGGAGE COMPARTMENT STORAGE SPACE AND FITTINGS (2/2)
Anchorage points
Hooks 6 located on each corner of the
luggage compartment, allow the load to
be secured.
6
5

3.37
Always place the objects to be trans-
ported so that their largest side rests
against the back of the rear bench seat,
for normal loads (example A) or against
the back of the front seats B when the
rear bench seatbacks are folded down.
If you have to place objects on the
folded seat back, it is vital that you
remove the headrests before folding
the seat back so that it can be folded as
flat as possible against the seat.
TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT
A
Always position the hea-
viest items directly on the
floor. Use the lashing points
on the floor of the luggage
compartment, if these are fitted to
the vehicle. The luggage should be
loaded in such a way that no items
will be thrown forward and strike the
occupants if the driver has to brake
suddenly. Fasten the rear seat belts,
even if the seats are not occupied.
B

3.38
Permissible nose weight, maxi-
mum permissible towing weight,
braked and unbraked: refer to
the information on “Weights” in
Section 6.
Choice and fitting of towing
equipment
Maximum weight of towing equip-
ment: 21 kg
For fitting and conditions of use,
refer to the equipment’s fitting in-
structions.
Please keep these instructions with
the rest of the vehicle documenta-
tion.
TRANSPORTING OBJECTS towbar
Normal chassis C = 832 mm
Long chassis C:
5 and 7 seats = 981 mm
C
If the towbar ball obscures the regis-
tration plate or the rear fog lights, it
should be removed when not in use.
In all cases, comply with local leg-
islation.

3.39
LUGGAGE NET (1/2)
3
5
– attach the two hooks 3 on the net
straps 4 to the anchoring points 5;
– adjust net strap 4 so that it is taut.Fitting the luggage net
behind the front seats
Inside the vehicle on each side:
– lower cover 1 to gain access to the
anchoring points for the top part of
the luggage net;
– insert the top rod of net 2 into the an-
choring points;
Depending on the vehicle, this may be
used when transporting animals or lug-
gage to isolate them from the passen-
ger section.
It can be positioned:
– behind the rear seats
A;
– behind the front seats B.
The luggage net is de-
signed to retain a maximum
weight of 10 kg.
Risk of injury.Do not install the luggage
net in this position when a
passenger is occupying a
rear seat
4
A
B
12

3.40
LUGGAGE NET (2/2)
11
6
Depending on the vehicle, remove the
anchoring rings 11 before installing a
luggage net.
– attach net strap hook
8 to the lower
ring;
– adjust net strap 9 so that it is taut.
– adjust the position of the second row seats: ensure that the seatbacks do
not touch the luggage net.
Note: recess 10 should be on the side
of the centre seat belt feed.Fitting the luggage net
behind the rear seats
(behind the second row rear seats on
the 7-seater version)
Inside the vehicle on each side:
– push the second row seats fully for- ward;
– lift cover 6 to access the luggage net
upper mounting rail;
– insert upper rod 7 for the net into the
rail;
9
8
10
76