RENAULT KANGOO 2001 KC / 1.G 4x4 - Mechanism And Accessories And Trim And Upholstery Workshop Manual

Special Features of the 4x4
Mechanisms and accessories
Trim and upholstery
KC0L - KC0P - KC0S - KC0V
Refer to the Workshop Repair Manual for parts not mentioned in this manual. 326
77 11 306 182
"The repair methods given by the manufacturer in this document are based on the
technical specifications current when it was prepared.
The methods may be modified as a result of changes introduced by the manufacturer
in the production of the various component units and accessories from which his
vehicles are constructed."
JULY 2001
All copyrights reserved by Renault.
EDITION ANGLAISE
Copying or translating, in part or in full, of this document or use of the service part
reference numbering system is forbidden without the prior written authority of Renault.
© RENAULT 2001

Contents
Page
55
58
71
EXTERIOR PROTECTION
Front bumper 55-1
Side protective mouldings 55-3
Front wing extenders 55-5
Sill panel 55-6
UPPER INTERIOR ACCESSORIES
Storage compartment 58-1
BODY INTERNAL TRIM
Side trim panels 71-1 A
B
C
D
A
A
Mechanisms and accessories
Trim and upholstery

EXTERIOR PROTECTION
Front bumper
55
155EXTERIOR PROTECTION
Front bumper
NOTE: The bumper is removed in the same way as on
the basic model, only dismantling is different.
DISMANTLING
Remove:
– the bumper,
– the bolt (A).
Release the clips (B), then remove the fog light.
Disconnect the connector.
Take out the rivets (C).
Release the clips (D), then remove the bumper trim.Take out the rivets (E).
Release the clips (F), then remove the lower casing.
Release the clips (G), then remove the absorber.
55-1
A

EXTERIOR PROTECTION
Front bumper
55
55-2
Release:
– the clips (I) and (J), then remove the grilles,
– the clips (K), then remove the towing hitch access
cover.
A

EXTERIOR PROTECTION
Side protective mouldings
55
55-3
Side protective mouldings
REMOVING THE FRONT DOOR MOULDING
Remove the bolt (A).Slide the moulding towards the rear of the vehicle (1).
IMPORTANT: the indexing clips (B) cannot be
removed without being damaged, so always fit new
ones after removal (e.g. after a panel straightening
operation).
B

EXTERIOR PROTECTION
Side protective mouldings
55
55-4
Release the two clips (C), then remove the badge.
REMOVING THE REAR DOOR MOULDING
Slide the moulding towards the front of the vehicle (2).Remove the strips as illustrated above.
SPECIAL FEATURES OF REFITTING THE FRONT
AND REAR DOOR MOULDINGS
Position the strips on the moulding, then clip the
moulding to the door.
NOTE: only indexing strips can be left on the panel
while the mouldings are removed.
B

EXTERIOR PROTECTION
Front wing extenders
55
55-5
Front wing extenders
REMOVAL
Unclip the upper section of the extender (1).
Release the three clips (A), then remove the extender.
C

EXTERIOR PROTECTION
Sill panel
55
55-6
Sill panel
REMOVAL
Remove the front wing extender.
Unclip:
– the upper section of the sill panel (1),
– the lower section of the sill panel (A).Remove the nuts (B), then release the sill panel
mounting.
D

UPPER INTERIOR ACCESSORIES
Storage compartment
58
158UPPER INTERIOR ACCESSORIES
Storage compartment
REMOVAL
Remove:
– the three bolts (A),
– the four clips (B),
– the bolt (C), then release the trim.Remove the two screws (D).
Remove the trim (E).
Remove the three screws (F).
Partially unscrew the two screws (G), then release the
storage compartment mounting.
58-1
A

INTERIOR BODY LININGS
Side trim panels
71
171INTERIOR BODY LININGS
Side trim panels
REMOVAL
Remove:
– the rear parcel shelf,
– the emergency spare wheel,
– the jack,
– the four fastenings (A), then release the emergency
spare wheel support,
– the two clips (B), then release the trim (1).
71-1
A