ignition RENAULT KANGOO 2013 X61 / 2.G Instrument Panel Instruments Workshop Manual

83A-2
AFTER REPAIRCheck for correct operation.
V1 MR-376-X76-83A000$010.mif
83A
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding method applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this document):
– Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
– Visu-Schéma.
Type of diagnostic tools
–CLIP
Special tooling required
3. REMINDERS
Procedure
To run fault finding on the instrument panel, switch on the ignition in fault finding mode (+ after ignition).
Customer complaints - Fault finding chart
As the RENAULT diagnostic tool cannot be used to carry out fault finding on the instrument panel, fault finding is
carried out by means of customer complaints and fault finding charts
*VLL — Very Long LifeVehicle(s): KANGOO VLL*
Function concerned: Instrument panel
Special tooling required:
Diagnostic tool
Multimeter
A summary of the overall procedure to follow is provided on the following page in the form of a flow chart.
INSTRUMENT PANEL INSTRUMENTS
Fault finding – Introduction

83A-6
AFTER REPAIRCheck for correct operation.
V1 MR-376-X76-83A000$010.mif
INSTRUMENT PANEL INSTRUMENTS
Fault finding – Introduction83A
ACCESS TO FAULT FINDING MODE AND CHANGE OF PAGES
This function is viewed:
Version with and without trip computer
Input:
– By pressing and holding the odometer Reset button for 5 seconds when switching on the after ignition feed.
Scrolling:
– To scroll the trip computer information, press the odometer Reset button repeatedly.
Output:
– The fault finding phase ends automatically after 5 minutes.
– The fault finding phase ends after the ignition is switched off.
– The fault finding phase can be ended by pressing and holding the mileage counter reset button, which clears the
stored faults.
DESCRIPTION OF THE NEEDLE INDICATOR TEST SEQUENCE
The needle indicators are activated at the same time.
The speedometer displays, for 1 second in increments of 24 mph (40 km/h), speeds ranging from 0 to 102 mph
(170 km/h).
The rev counter displays, for 1 second in increments of 1000 rpm, values ranging from 0 to 7000 rpm.

83A-8
AFTER REPAIRCheck for correct operation.
V1 MR-376-X76-83A000$020.mif
83A
1. OPERATION OF THE NEEDLE INDICATORS
Speedometer
The vehicle speed signal is transmitted to the instrument panel by a wire link.
The information is produced by the ABS computer or a speed sensor located on the gearbox.
Engine speed indicator
The engine speed signal is transmitted to the instrument panel by a wire connection (signal provided by the injection
computer).
2. OPERATION OF THE TRIP COMPUTER
Coolant temperature bargraph
The coolant temperature signal is transmitted to the instrument panel by a wire connection.
The signal is produced by the coolant temperature sensor.
Above 115°C (inclusive), all the segments are illuminated with the warning light.
From 105°C (inclusive) to 115°C (not inclusive), six segments are illuminated.
From 80°C (inclusive) to 105°C (not inclusive), four segments are illuminated.
From 50°C (inclusive) to 80°C (not inclusive), two segments are illuminated.
No segments are illuminated when the temperature is below 50°C.
Fuel level bargraph and low fuel level warning light
The separate "low fuel level" warning light comes on when the reserve level is reached and nine segments of the
bargraph are extinguished.
The wire signal from the fuel sender is processed to calculate the fuel level and manage the warning light.
SPECIAL NOTE ABOUT OPERATION WHEN THE IGNITION IS SWITCHED ON:
A 3 second self-test is run on the "low fuel level" warning light when the ignition is switched on.
Case 1: if the fuel sender is connected but the fuel level in the tank is lower than the reserve threshold, the
continued illumination of the warning light after 3 seconds depends on the fuel level signal (smoothed and taking
into account recalibrations).
Case 2: if the fuel sender is not connected and it is the first time the fault appears when switching on the ignition, the
low fuel level warning light first flashes quickly for 2 seconds, then after 1 minute 40 seconds maximum (fault
detection time), the fuel level bargraph goes out, then the low fuel level warning light is illuminated continuously.
Case 3: if the fuel sender is not connected and the warning light had been illuminated before the ignition was
switched on this time, the low fuel level warning light stays illuminated, then after 1 minute 40 seconds, all the
bargraph segments go out.
INSTRUMENT PANEL INSTRUMENTS
Fault finding – System operation

83A-9
AFTER REPAIRCheck for correct operation.
V1 MR-376-X76-83A000$020.mif
INSTRUMENT PANEL INSTRUMENTS
Fault finding – System operation83A
Oil pressure warning light
When the ignition is switched on, the oil pressure warning light illuminates.
When the engine is running and the oil pressure is sufficient, the warning light goes out.
The oil pressure signal is transmitted to the instrument panel by a wire connection.
The signal is produced by the oil pressure switch.
3. ODOMETER
Total mileage
The total mileage is displayed as soon as the ignition is switched on.
Press the Trip computer scroll button or the Reset button to move to the next page.
Trip mileage
The trip mileage is displayed instead of the total mileage when the Trip computer or the Reset button is pressed
briefly.
Except in the following cases:
– it is reset by a long press of the instrument panel Reset button,
– resetting the trip mileage is different from resetting the trip computer (distance travelled).
Trip computer
The various sequences of the trip computer can be displayed instead of the mileage by pressing the button at the
end of the wiper stalk (Trip computer button). It is reset by a long press of the Reset button.
The signals from the trip computer are displayed after the trip mileage as follows:
–Fuel consumed (in litres per 100 km) since the last reset,
–Average consumption (in litres per 100 km) since the last reset.
This is only displayed after the vehicle has travelled 400 m.
This takes into consideration the distance covered and the fuel consumption since the last time the reset button was
pressed.

83A-14
AFTER REPAIRCheck for correct operation.
V1 MR-376-X76-83A000$030.mif
INSTRUMENT PANEL INSTRUMENTS
Fault finding – Allocation of computer tracks83A
CONNECTOR (24-track black)
Tracks Description
1Control - software lock indicator light
2Coolant temperature warning light - control
3Right turn signal indicator light
4Emission control fault warning light
5Rear fog lights indicator light
6Front fog lights indicator light
7 Earth
8Earth
9+ Battery supply
10After ignition supply
11+ Side lights supply
12Coolant temperature + signal
13Alternator charge warning light - control
14Left turn signal indicator light
15Preheating/electronic fault warning light
16Handbrake + fluid level warning light - control
17Heated rear screen indicator light
18Not used
19Not used
20Airbag fault warning light
21Rev counter signal
22Vehicle speed signal
23Trip computer scroll - control
24Fuel sending unit + signal

83A-18
AFTER REPAIRCheck for correct operation.
V1 MR-376-X76-83A000$050.mif
INSTRUMENT PANEL INSTRUMENTS
Fault finding – Customer complaints83A
FRONT FOG LIGHTS
THE WARNING LIGHT OPERATES INCONSISTENTLY ALP16
ABS FAULT
THE WARNING LIGHT OPERATES INCONSISTENTLY ALP17
ENGINE IMMOBILISER
THE ENGINE IMMOBILISER WARNING LIGHT REMAINS LIT OR
FLASHES WHEN DRIVINGALP18
WARNING LIGHT REMAINS NOT LIT WHEN NOT UNDER AFTER
IGNITION FEEDALP19
BATTERY CHARGE FAULT
WARNING LIGHT REMAINS LIT (engine running) ALP20
HANDBRAKE APPLIED AND FAULT DETECTED ON BRAKING CIRCUIT
THE WARNING LIGHT OPERATES INCONSISTENTLY (WITHOUT
ABS)ALP21
THE WARNING LIGHT OPERATES INCONSISTENTLY (WITH ABS) ALP22

83A-19
AFTER REPAIRCheck for correct operation.
V1 MR-376-X76-83A000$050.mif
INSTRUMENT PANEL INSTRUMENTS
Fault finding – Customer complaints83A
*CPE: Electric central door lockingHEATED REAR SCREEN
THE WARNING LIGHT DOES NOT LIGHT UP ALP23
INSTRUMENT PANEL
NO DISPLAY WHEN IGNITION IS SWITCHED ON ALP24
TRIP COMPUTER OR TRIP METER OR CLOCK
RESET WHENEVER THE IGNITION IS SWITCHED OFF ALP25
DOOR OPEN WARNING LIGHT
THE WARNING LIGHT DOES NOT ILLUMINATE (WITHOUT ELECTRIC
CENTRAL DOOR LOCKING*)ALP26
THE WARNING LIGHT DOES NOT ILLUMINATE (WITH ELECTRIC
CENTRAL DOOR LOCKING*)ALP27

83A-22
AFTER REPAIRCheck for correct operation.
V1 MR-376-X76-83A000$060.mif
INSTRUMENT PANEL INSTRUMENTS
Fault finding – Fault Finding Chart83A
ALP 3 The fuel level indicator does not display full
NOTESThe fuel tank must be filled with the ignition switched off (advise the customer to remove
the key).
Ideally the customer must fill the tank with at least 15 litres.
See Wiring Diagrams Technical Note for Kangoo VLL.
Ask the customer if the tank is filled up under the following
conditions:
– the customer filled the tank up to the 3
rd cut-out
– the customer has changed filling station
– the customer filled the tank in a flat-level station (not on
a slope).
Did the customer fill the tank while observing all of
these conditions?Ask the customer to return just after
having filled the tank under the conditions
mentioned above.
With the ignition off, disconnect the fuel sender
connector, component code 199 and then check the
resistance using a multimeter.
The value should be 51 .
Is the value measured in the correct range,
depending on the vehicle equipment?Replace the sender, component code 199
(see MR 374, Mechanical, 19C, Fuel
tank, Pump - Sender: Removal -
Refitting).
If the fault is still present, contact Techline.
NO
YES
NO
A

83A-27
AFTER REPAIRCheck for correct operation.
V1 MR-376-X76-83A000$060.mif
INSTRUMENT PANEL INSTRUMENTS
Fault finding – Fault Finding Chart83A
ALP 6Fault with no warning given by warning light (no addition of fuel
since the fault)
NOTESPut the vehicle in + after ignition.
See Wiring Diagrams Technical Note for Kangoo VLL.
Check the instrument panel warning lights, component code
247.Replace the instrument panel,
component code 247 (see MR
430, Mechanical, 83A,
Instrument panel, Instrument
panel: Removal - Refitting). Does the fuel warning light illuminate for 3 seconds when
+ after ignition is switched on?
The warning resistance is equal to 290 .
With the ignition off, disconnect the fuel sender connector,
component code 199 and then check the resistance using a
multimeter.Replace the sender, component
code 199 (see MR 374,
Mechanical, 19C, Fuel tank,
Pump - Sender: Removal -
Refitting). Is this value greater than or equal to the warning value
corresponding to the type of fuel?
NO
YES
NO
A
YES

83A-29
AFTER REPAIRCheck for correct operation.
V1 MR-376-X76-83A000$060.mif
INSTRUMENT PANEL INSTRUMENTS
Fault finding – Fault Finding Chart83A
ALP 7Fault with no warning given by warning light (addition of fuel
since the fault)
NOTESPut the vehicle in + after ignition.
See Wiring Diagrams Technical Note for Kangoo VLL.
Check the instrument panel warning lights, component
code 247.
Does the fuel warning light illuminate for 3
seconds when + after ignition is switched on?Replace the instrument panel, component
code 247 (see MR 430, Mechanical, 83A,
Instrument panel, Instrument panel:
Removal - Refitting).
After filling the fuel tank, has the fuel level on the
instrument panel changed?Consult the interpretation of ALP4 Addition
of fuel not registered (not full).
Empty the fuel tank and consult the interpretation of
ALP6 Fault with no warning given by warning light
(no addition of fuel since the fault).
NO
YES
NO
YES