ABS RENAULT KANGOO 2013 X61 / 2.G Power Steering Pump Assembly Workshop Manual

36B-16V1 MR-376-X76-36B000$100.mif
POWER-ASSISTED STEERING PUMP ASSEMBLY
Fault finding – Conformity check36B
GEPDA
Vdiag No.: 04
Main screen (continued)
NOTESOnly perform this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Test conditions: Engine stopped, ignition on.
FunctionParameter or status
Checked or actionDisplay
and notesFault finding
Electric motorPR012: Current absorbed
by the motor0 A < PR012 < 1 A.In the event of a fault,
apply the interpretation of
parameter PR012.
Electric motor
speedPR017: Speed setpoint Indicates the speed of the
electric motor on the
power-assisted steering
pump assembly.
PR004 = PR017 = 0 rpm.In the event of a fault,
apply the interpretation of
parameter PR017
PR004: Engine speed In the event of a fault,
apply the interpretation of
parameter PR004

36B-18V1 MR-376-X76-36B000$100.mif
POWER-ASSISTED STEERING PUMP ASSEMBLY
Fault finding – Conformity check36B
GEPDA
Vdiag No.: 04
Main screen (continued)
NOTESOnly perform this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Test conditions: Engine idling.
FunctionParameter or status
Checked or actionDisplay
and notesFault finding
Electric motorPR012: Current absorbed
by the motor5 A < PR012 < 65 A.In the event of a fault, apply
the interpretation of parameter
PR012
Electric motor
speedPR017: Speed setpoint Indicates the speed of
the electric motor on
the power-assisted
steering pump
assembly. PR004 =
PR017= 2650 rpmIn the event of a fault, apply
the interpretation of parameter
PR017
PR004: Engine speed In the event of a fault, apply
the interpretation of parameter
PR004

36B-19V1 MR-376-X76-36B000$110.mif
36B
GEPDA
Vdiag No.: 04
Tool Parameter Diagnostic tool title
PR004Engine speed
PR008Computer temperature
PR012Current absorbed by the motor
PR016Oil temperature
PR017Speed setpoint
PR108Computer feed voltage
POWER-ASSISTED STEERING PUMP ASSEMBLY
Fault finding – Parameter summary table

36B-21
AFTER REPAIRPerform a test using the diagnostic tool.
V1 MR-376-X76-36B000$120.mif
POWER-ASSISTED STEERING PUMP ASSEMBLY
Fault finding – Interpretation of parameters36B
GEPDA
Vdiag No.: 04
PR012CURRENT ABSORBED BY THE MOTOR
NOTESNone.
Parameter PR012 indicates the current actually consumed by the electric motor of the power-assisted steering
pump assembly.
This parameter is always positive.
If the parameter does not comply with the values indicated in the Conformity check, refer to the interpretation of
fault DF017 Motor circuit.
GEPDA_V04_PR012

36B-27
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-36B000$150.mif
POWER-ASSISTED STEERING PUMP ASSEMBLY
Fault finding – Fault Finding Chart36B
GEPDA
Vdiag No.: 04
ALP1
CONTINUED
Disconnect the two connectors from the computer on the power-assisted steering pump assembly.
Check the condition and conformity of the connectors on the power-assisted steering pump assembly and their
clips.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the conformity of the electrical supplies (they must be equal to the battery voltage) on the following
connections:
●BP15 on component 186,
●M of component 186,
●AP4 (for MERCOSUR) or AP23 (for BURSA or for Kangoo VLL) on the component 186.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance of the wiring harness between the
diagnostic socket and the connector on the computer of the power-assisted steering pump assembly on the
following connection:
●HK between components 225 and 186.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the techline.

36B-28
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-36B000$150.mif
POWER-ASSISTED STEERING PUMP ASSEMBLY
Fault finding – Fault Finding Chart36B
GEPDA
Vdiag No.: 04
ALP2 Poor vehicle handling
NOTESOnly consult this customer complaint after a full check with the diagnostic tool.
Special note:
Use the Wiring Diagrams Technical Note for Thalia 2/Symbol 2 and Kangoo VLL.
Check the pressure and condition of the tyres, the condition of the joints and the front axle geometry.
Check the battery voltage of the vehicle and the condition of the battery terminals, component code 107.
Check the condition and presence of power fuse F02 (80A) (for MERCOSUR) or F05 (80A) (for BURSA or for
Kangoo VLL) on the power-assisted steering pump assembly, component code 186 (see MR 423 or MR 374,
Mechanical, 81C, Fuses, Fuses: List and location of components).
Check the condition and presence of + after ignition fuse F18 (7.5A) on the power-assisted steering pump
assembly, component code 186 (see MR 423 or MR 374, Mechanical, 81C, Fuses, Fuses: List and location of
components).
Check the insulation, continuity and absence of interference resistance on the following connection:
●BP15 between components 186 and 777or 260.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the rotation speed of the electric motor is equal to 2650 rpm. If not, contact the Techline.
If the fault is still present, contact the techline.
GEPDA_V04_ALP02

36B-30
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-36B000$150.mif
POWER-ASSISTED STEERING PUMP ASSEMBLY
Fault finding – Fault Finding Chart36B
GEPDA
Vdiag No.: 04
ALP4 Assistance available without starting vehicle engine
NOTESOnly consult this customer complaint after a full check with the diagnostic tool.
Special note:
Use the Wiring Diagrams Technical Note for Thalia 2/Symbol 2 and Kangoo VLL.
Check the condition of the connection of the alternator signal connector, on the vehicle alternator, component code
103.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the charging circuit if necessary (see Technical Note 6014A, Checking the charging circuit).
Check that the battery charge warning light illuminates on the instrument panel during + after ignition with the
vehicle engine stopped.
Check the insulation, continuity and absence of interference resistance on the following connection:
●2A between components 186 and 103.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the techline.
GEPDA_V04_ALP04