RENAULT MEGANE SCENIC 1995 Service Repair Manual

INJECTION
Adaptive richness correction
17
Zone n° 5
(mbars)Zone n° 4
(mbars)Zone n° 3
(mbars)Zone n° 2
(mbars)Zone n° 1
(mbars)
300410500 590 680870
Average 355 Average 455 Average 545 Average 635 Average 775
280390510 620 740930
Average 335 Average 450 Average 565 Average 680 Average 835
F3R
K7M Pressure zones to cover during the test (# 01)
Following this test the corrections will be operational.
# 31 varies more significantly for idle speed and low loads and # 30 for average and high loads, but both are
operational over all of the manifold pressure ranges.
The test should be followed by a normal, varied drive, covering 3 to 6 miles (5 to 10 km).
After the test, read the values for # 30 and # 31. Initially 128, they should now have changed.If they have not
changed, repeat the test, taking care to ensure the test conditions are correctly observed.
ROAD TEST
Conditions :
- Engine warm (coolant temperature > 70° C)
- Do not exceed engine speed4 300 rpmF3R engine
and 4 000 rpmK7M engine
For this test, start from a fairly low engine speed, in 3rd or 4th gear using progressive acceleration to stabilise
the required pressure for 10 seconds in each zone (see table).
NOTE: For the F3R engine, for example, for zone n° 1, try to maintain the average of 355 mb for at least 10 se-
conds.
17-37

INJECTION
Adaptive richness correction
17
Special notes for the E7J engine
A road test should be carried out after which the engine should be allowed to idle for a few minutes. The va-
lues for #30 and #31 should have changed.
During the road test, stabilise the engine speed for a few moments between 2 000 rpm and 4 400 rpm and the
manifold pressure between 400 and 700 mbars.
Condition #31 : if engine speed < 1 000 rpm and if the manifold pressure < 450 mbars, #31 should be mo-
dified.
INTERPRETING VALUES GATHERED AFTER A ROAD TEST
If there is a lack of fuel (injectors dirty, fuel pressure and flow too low...), richness regulation # 35 increases to
obtain the richness as close as possible to richness 1 and adaptive correction # 30 and # 31 increases until the
richness correction returns to oscillate around 128.
If there is an excess of fuel, the situation is reversed:
Richness regulation # 35 reduces and adaptive correction # 30 and # 31 also reduces to recentre the richness
correction (# 35) around 128.
NOTE: the analysis which may be made using # 31 remains difficult since this correction mainly operates for
idle speed and low loads and is also very sensitive.
Hasty conclusions should not therefore be drawn from this gate value, rather the position of # 30 should be
examined.
The information from these two gates gives an idea about the engine operation richness, and may be used as
a guide for fault finding. For them to be of use during fault finding, conclusions may only be drawn if the va-
lues are at the minimum or maximum correction thresholds, and if both values have drifted in the same direc-
tion.
IMPORTANT : # 30 and # 31 should only be examined and analysed after a customer complaint, an opera-
ting fault and if they are at the threshold with the value for # 35 also offset (# 35 varies above 175 or be-
low 80).
17-38

INJECTION
Operating wiring diagram
17
KEY TO OPERATIONAL WIRING DIAGRAMS (E7J, F3R, K7M)
COMPONENT NO DESCRIPTION
109
119
120
146
147
149
193 to 196
218
222
224
225
228
236
238
242
244
247
250
272
310
319
341
371
398
437
565
597
645
649
663
664
679
746
772
777
927
MF
MHOn board computer
Automatic transmission computer
Injection computer
Pinking sensor (located under the inlet manifold for E7J engine)
Absolute pressure sensor
TDC sensor
Injectors
Fuel pump
Throttle position potentiometer
Power assisted steering pressostat
Diagnostic socket
Idle speed regulation micromotor
Fuel pump relay (in engine fuse box)
Injection feed locking relay
Oxygen sensor
Coolant temperature sensor
Instrument panel
Vehicle speed sensor
Air temperature sensor
Ignition power module
Air conditioning control panel
Idle speed regulation solenoid valve
Fuel vapour recirculation solenoid valve
Exhaust gas recirculation solenoid valve (EGR)
Throttle body heater (under throttle body)
Throttle body assembly
Engine fuse box
Passenger compartment connection unit
Idle speed regulation stepping motor
Dual ignition coil n°1 (cylinders 1 and 4)
Dual ignition coil n° 2 (cylinders 2 and 3)
Radio anti-interference condenser
Cylinder reference sensor
Heater relay (in engine fuse box)
Power fuse board (near battery)
Inertia switch
Rear right hand electrical earth
Engine electrical earth (located on the cylinder block between the starter and the al-
ternator for the E7J engine)
17-39

INJECTION
Operating wiring diagram
17
E7J engine
PRJ99528
17-40

INJECTION
Operating wiring diagram
17
E7J engine
COMPUTER TRACK ALLOCATION
TrackALLOCATION
1Power earth
2Electronic earth
3Vehicle speed information
4+ before ignition (permanent) computer memory
5Canister bleed signal (sequential earth period)
6Pump relay control (via track N° 2)
7Locking relay control (via track N° 2)
8Diagnostic line for erasing the memory and power assisted steering pressostat information
9Throttle position potentiometer information (pin N° 4 on 222)
10Heater relay command
11TDC sensor signal (track B)
12Rev counter information at instrument panel
13Connection with injection fault warning light on instrument panel
14Air temperature information
15Coolant temperature information
16+ 5 V feed for absolute pressure sensor and throttle potentiometer
17Common earth for absolute pressure sensor, throttle potentiometer and coolant temperature
sensor
18Emission of diagnostic signal to diagnostic socket
19Main computer feed via injection locking relay
20Air conditioning compressor command
21Injector control via earth
22Not used
23+ or - feed to idle speed micromotor (pin N° 1)
24+ or - feed to idle speed micromotor (pin N° 2)
17-41

INJECTION
Operating wiring diagram
17
E7J engine
TrackALLOCATION
25No load information input
26Not used
27Power module command
28TDC sensor signal input (track A)
29Immobiliser coded line input via decoder unit
30+ 12 V information when ignition turned on
31Pinking sensor noise signal input
32+ 12 V after ignition information
33Voltage information dependent on manifold pressure seen by sensor (on track B)
34Air conditioning compressor operation request input
35Voltage from oxygen sensor input
17-42

INJECTION
Operating wiring diagram
17
K7M engine
PRJ99475
17-43

INJECTION
Operating wiring diagram
17
K7M engine
COMPUTER TRACK ALLOCATION
TrackALLOCATION
1Not used
2Power earth n° 1
3Power earth n° 2
4Command for injector n° 2 and n° 3 via earth
5Air conditioning on - off information and request for compressor operation authorisation
(0 - 12 V)
6Heated windscreen information (0 - 12 V)
7Park / Neutral / torque reduction information (0 - 5 V) (K7M 703)
8Pinking sensor signal
9Stepping motor control (0 - 12 V)
10EGR solenoid valve control (0 - 12 V) (K7M 703)
11Bi-directional diagnostic line K used for entry into fault finding mode
(looking for computer), emission of diagnostic signals from computer, application of command
modes (G..*), erasing the memory (G0**)
and ending fault finding (G13*)
12Vehicle speed information
13Power assisted steering pressostat information
14Not used
15Coolant temperature sensor information
16Manifold pressure information transcribed by absolute pressure sensor
17Voltage information from oxygen sensor
18Earth
19Throttle position potentiometer information
20Air temperature sensor information
21Not used
22Not used
23Not used
24+ 12 V after ignition
17-44

INJECTION
Operating wiring diagram
17
TrackALLOCATION
25Not used
26Not used
27Not used
28Command for coil for cylinders 1 and 4
29Command for coil for cylinders 2 and 3
30Command for injector n° 1 and n° 4 via earth (n° 1 flywheel end)
31Pinking sensor screened cable
32+12 V before ignition
33TDC sensor signal (track B)
34TDC sensor signal (track A)
35Stepping motor command (0 - 12 V)
36Stepping motor command (0 - 12 V)
37Immobiliser coded line input
38Uni-directional diagnostic line L for entry into diagnostic mode only
(looking for computer)
39Not used
40Stepping motor command (0 - 12 V)
41Throttle angle information for automatic transmission computer
42RCO control (sequential earth period for canister bleed solenoid valve RCO)
43Command for injection fault warning light on instrument panel
44Common earth for pinking sensor and coolant temperature sensor and absolute pressure sensor
45+ 5 V feed for absolute pressure sensor and throttle position potentiometer
46Common earth for air temperature sensor and throttle position potentiometer
47Not used
48Command (via earth) for fuel pump relay and engine speed information
49Not used
K7M engine
17-45

INJECTION
Operating wiring diagram
17
TrackALLOCATION
50Fuel flow information for on board computer
51Air conditioning compressor clutch operation prevention command
(0 V → authorisation ; 12 V → prevention)
52Monitoring of injector feed and fuel pump feed from relay (236)
53Not used
54Not used
55Not used
K7M engine
17-46