tow RENAULT PULSE 2012 1.G Owners Manual


> (GLW    0RGHO .$2(0B5HQDXOW @
1-6Safety — seats, seat belts and supplemental restraint system
Adjustment
SSS0288
1. Pull u\f the head restra\bnt to ra\bse to the \fro\fer\fos\bt\bon.
2. Push \bn the lock knob
*1and \fush down the
head restra\bnt to lower to the \fro\fer \fos\bt\bon.
The rear head restra\bnt (\bf equ\b\f\fed) should only be
used \bn the notched stem \fos\bt\bons. The lowest head
restra\bnt \fos\bt\bon \bs the stowed \fos\bt\bon.
ARMREST (\bf equ\b\f\fed)
Front
SSS0970
Pull the armrest down unt\bl \bt \bs hor\bzontal.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
1-10Safety — seats, seat belts and supplemental restraint system
SSS0467
3. Position the la\f belt \fortion low an\b snug on thehi\fs as shown.
4. Pull the shoul\ber belt \fortion towar\b the retractor to take u\f extra slack. Be sure the shoul\ber belt is
route\b over your shoul\ber an\b is snug across your
chest.
Shoul\ber belt height a\bjustment (if equi\f\fe\b
for front seats)
SSS0351A
WARNING:
.The shoulder belt anchor height should be
adjusted to the position best for you. Failure
to do so may reduce the effectiveness of the
entire restraint system and increase the
chance or severity of injury in an accident.
. The shoulder belt should rest on the middle
of the shoulder. It must not rest against the
neck.
. Be sure that the seat belt is not twisted in
any way.
. Be sure that the shoulder belt anchor is
secured by trying to move the shoulder belt
anchor up and down after adjustment.
The shoul\ber belt anchor height shoul\b be a\bjuste\b to
the \fosition best for you.
The belt shoul\b be away from your face an\b neck, but
not falling off your shoul\ber.
To a\bjust, \full the release button
*1an\b move the
shoul\ber belt anchor to the \fro\fer \fosition*2, so that
the belt \fasses over the center of the shoul\ber.
Release the button to lock the shoul\ber belt anchor
into \fosition.
Unfastening seat belts
Push the button on the buckle. The seat belt
automatically retracts.
Belt hook
SSS1090
Hook the seat belt at the belt hook when fol\bing \bown
the rear seat.
NOTE:
Before folding down the rear seatback, make
sure that the seat belt tongue is securely
fastened to the belt clip. Also, make sure that
the seat belt does not get caught in the seatback
when folding down the rear seat.
Checking seat belt o\feration
Seat belt retractors are \besigne\b to lock seat belt
movement:
. When the seat belt is \fulle\b quickly from the
retractor.
. When the vehicle slows \bown ra\fi\bly.
To increase your confi\bence in the seat belts, check
the o\feration by gras\fing the shoul\ber belt an\b \fulling
forwar\b quickly. The retractor shoul\b lock an\b restrict
further belt movement. If the retractor \boes not lock
\buring this check, contact a RENAULT \bealer im-
me\biately.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
Rear center seat belt (if equipped)
SSS\f391
\bhe rear center seat belt has a connector tongue*1and a seat belt tongue*2. Both the connector tongue
and the seat belt tongue must be securely latched for
proper seat belt operation.
SSS\f241
WARNING:
. Always fasten the connector tongue and the
seat belt in the order shown.
. Always make sure both the connector ton-
gue and the seat belt tongue are secured
when using the seat belt. Do not use it with
only the seat belt tongue attached. This could result in serious personal injury in
case of an accident or a sudden stop.
JVR\f\f\f3X
Stowing rear center seat belt:
When folding down the rear seat, the rear center seat
belt can be retracted into a stowed position.
1. Hold the connector tongue
*1so that the seat
belt does not retract suddenly when the tongue is
released from the connector buckle. Release the
connector tongue by inserting a suitable tool such
as key
*2into the connector buckle. 2. Retract the seat belt and store the seat belt
tongue and connector tongue on the stowed
position
*3.
WARNING:
.Do not unfasten the rear center seat belt
connector except when folding down the
rear seat.
. When returning the seatback, be sure to
attach the rear center seat belt connector.
JVR\f\f\f4X
Safety — seats, seat belts and supplemental restraint system1-11
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
1-12Safety — seats, seat belts and supplemental restraint system
Attaching rear center seat belt:
Always be sure the rear center seat belt connector
tongue an\f connector buckle are attache\f. D\bscon-
nect only when fol\f\bng \fown the rear seat.
To connect the buckle:
1. Pull the seat belt tongue an\f connector tonguefrom the stowe\f pos\bt\bon
*1.
2. Pull the seat belt an\f secure the connector buckle unt\bl \bt cl\bcks
*2.
The center seat belt connector tongue can be attache\f
only \bnto the rear center seat belt connector buckle.
To fasten the seat belt, see “Fasten\bng seat belts” (P.1-
9) .
WARNING:
. When attaching the rear center seat belt
connector, be certain that the seatbacks are
completely secured in the latched position
and the rear center seat belt connector is
completely secured.
. If the rear center seat belt connector and the
seatbacks are not secured in the correct
position, serious personal injury may result
in an accident or sudden stop.
JVR0006X
CAUTION:
Make sure to wear the rear center seat belt with
the seat belt passing through the path*A.
TWO-POINT TYPE SEAT BELTS (\bf
equ\bppe\f)
Fasten\bng seat belts
SSS0448
WARNING:
The seatback should not be in a reclined
position any more than needed for comfort. Seat
belts are most effective when the passenger sits
well back and straight up in the seat.
1. Insert the tongue \bnto the buckle marke\f CENTER
unt\bl you hear an\f feel the latch engage.
SSS0541
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
CHECKING BULBS
With all doo\fs closed\b apply the pa\fking b\fake\b fasten
the seat belts and tu\fn the ignition switch to the “ON”
position without sta\fting the engine. The following
lights will illuminate:
\b\b\b\b.
If equipped\b the following lights will illuminate b\fiefly
and then tu\fn off:
o\f\b\b\b\b\b(\fed) \b(g\feen) \b\b\b\b.
If any lights fail to illuminate\b it may indicate a bu\fned-
out bulb o\f an open ci\fcuit in the elect\fical system.
Have the system checked\b and if necessa\fy \fepai\fed\b
by a RENAULT deale\f p\fomptly.
Some indicato\fs and wa\fnings a\fe also displayed on
the vehicle info\fmation display (if equipped) below the
speedomete\f. (See “Vehicle info\fmation display” (P.2-
20) .)
WARNING LIGHTS
\bAnti-lock B\faking System (ABS)
wa\fning light (if equipped)
When the ignition switch is in the “ON” position\b the
Anti-lock B\faking System (ABS) wa\fning light illumi-
nates and then tu\fns off. This indicates the ABS is
ope\fational.
If the ABS wa\fning light illuminates while the engine is
\funning\b o\f while d\fiving\b it may indicate the ABS is not
functioning p\fope\fly. Have the system checked by a
RENAULT deale\f p\fomptly.
If an ABS malfunction occu\fs\b the anti-lock function is
tu\fned off. The b\fake system then ope\fates no\fmally\b
but without anti-lock assistance. (See “B\fake system”
(P.5-36) .)
B\fake wa\fning light
WARNING:
. If the brake fluid level is below the minimum
mark on the brake fluid reservoir, do not
drive the vehicle until the brake system has
been checked by a RENAULT dealer.
. Even if you judge it to be safe, have your
vehicle towed because driving it could be
dangerous.
. Depressing the foot brake pedal without the
engine running and/or with a low brake fluid
level could increase the stopping distance
and require greater pedal travel distance
and effort.
The b\fake wa\fning light indicates the pa\fking b\fake
system ope\fation\b a low b\fake fluid level of the b\fake
system and an Anti-lock B\faking System (ABS)
malfunction.
Parking brake warning indicator:
When the ignition switch is in the “ON” position\b and
the pa\fking b\fake is applied\b the b\fake wa\fning light
illuminates. When the pa\fking b\fake is \feleased\b the
b\fake wa\fning light tu\fns off.
Low brake fluid warning indicator:
If the b\fake wa\fning light illuminates while the engine is
\funning\b o\f while d\fiving\b and the pa\fking b\fake is
\feleased\b it may indicate the b\fake fluid level is low.
When the b\fake wa\fning light illuminates while d\fiving\b
stop the vehicle safely as soon as possible. Stop the
engine and check the b\fake fluid level. If the b\fake fluid
level is below the minimum ma\fk on the \fese\fvoi\f\b add
b\fake fluid as necessa\fy. (See “B\fake fluid” (P.8-18) .) If the b\fake fluid level is sufficient\b have the b\fake
system checked by a RENAULT deale\f p\fomptly.
Anti-lock Braking System (ABS) warning indi-
cator (if equipped):
When the pa\fking b\fake is \feleased and the b\fake fluid
level is sufficient\b if both the b\fake wa\fning light and the
Anti-lock B\faking System (ABS) wa\fning light illumi-
nate\b it may indicate the ABS is not functioning
p\fope\fly. Have the b\fake system checked\b and if
necessa\fy \fepai\fed\b by a RENAULT deale\f p\fomptly.
(See “Anti-lock B\faking System (ABS) wa\fning light”
(P.2-13) .)
Cha\fge wa\fning light
When the ignition switch is in the “ON” position\b the
cha\fge wa\fning light illuminates. Afte\f sta\fting the
engine\b the cha\fge wa\fning light tu\fns off. This
indicates the cha\fging system is ope\fational.
If the cha\fge wa\fning light illuminates while the engine
is \funning\b o\f while d\fiving\b it may indicate the cha\fging
system is not functioning p\fope\fly and may need
se\fvicing.
When the cha\fge wa\fning light illuminates while
d\fiving\b stop the vehicle safely as soon as possible.
Stop the engine and check the alte\fnato\f belt. If the
alte\fnato\f belt is loose\b b\foken o\f missing\b the cha\fging
system needs \fepai\f. (See “D\five belts” (P.8-15) .)
If the alte\fnato\f belt appea\fs to be functioning co\f\fectly
but the cha\fge wa\fning light \femains illuminated\b have
the cha\fging system checked by a RENAULT deale\f
p\fomptly.
Instruments and controls2-13
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
Low fuel warning light (if equipped)
\fhe low fuel warning light illuminates when the fuel
level in the tan\b is getting low. Refuel as soon as it is
convenient, before the fuel gauge reaches the empty
(0) position. \fhere will be a small reserve of fuel
remaining in the tan\b when the fuel gauge reaches the
empty (0) position.
Malfunction warning light (red) (diesel
engine model)
When the ignition switch is placed in the “ON”
position, the malfunction warning light illuminates in
red. \fhis means that the system is operational. After
starting the engine, the warning light turns off.
For the orange Malfunction Indicator Light (MIL) , see
“Malfunction Indicator Light (MIL)” (P.2-17)for details.
If the malfunction warning light (red) illuminates
continuously while the engine is running, it may
indicate an engine control system malfunction. Have
your vehicle inspected by a RENAUL\f dealer. You do
not need to have your vehicle towed to the dealer.
CAUTION:
Continuing vehicle operation without proper
servicing of the engine control system could
lead to poor driveability, reduced fuel economy,
and damage to the engine control system, which
may affect the vehicle’s warranty coverage.
Master warning light (if equipped)
When the ignition switch is in the “ON” position, the
master warning light illuminates if any of the following
are displayed on the vehicle information display.
. Seat belt warning
. NO KEY warning
. Low fuel warning
. Par\bing bra\be release warning
. Door/bac\b door open warning
(See “Vehicle information display” (P.2-20) .)
P position selecting warning light (if
equipped)
\fhe warning light blin\bs in red when the ignition switch
is pushed to stop the engine with the selector lever in
any position except the “P” (Par\b) position.
If this warning appears, move the selector lever to the
“P” (Par\b) position or push the ignition switch to the
“ON” position.
An inside warning chime will also sound.
See “Intelligent Key system” (P.3-9) .
Seat belt warning light (if equipped)
When the ignition switch is in the “ON” position, the
seat belt warning light illuminates. \fhe light will
continue to illuminate until the driver’s seat belt is
fastened. (See “Seat belts” (P.1-7) .) For China:
When the vehicle speed exceeds 15 \bm/h (10 MPH) ,
the light will blin\b unless the driver’s seat belt is
securely fastened.
Except for China:
When the vehicle speed exceeds 15 \bm/h (10 MPH) ,
the light will blin\b and the chime will sound unless the
driver’s seat belt is securely fastened. \fhe chime will
continue to sound for about 90 seconds until the seat
belt is fastened.
Supplemental Restraint System (SRS)
air bag warning light (if equipped)
When the ignition switch is in the “ON” or “S\fAR\f”
position, the Supplemental Restraint System (SRS) air
bag warning light illuminates for about 7 seconds and
then turns off. \fhis indicates that the SRS air bag
system is operational.
If any of the following conditions occur, the SRS air
bag system and/or pre-tensioner seat belt need
servicing. Have the system chec\bed, and if necessary
repaired, by a RENAUL\f dealer promptly.
. \fhe SRS air bag warning light remains illuminated
after about 7 seconds.
. \fhe SRS air bag warning light flashes intermit-
tently.
. \fhe SRS air bag warning light does not illuminate
at all.
Unless chec\bed and repaired, the SRS air bag system
and/or pre-tensioner seat belt may not function
properly. (See “Supplemental Restraint System
(SRS)” (P.1-25) .)
Instruments and controls2-15
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
Malfunction Indicator Light (MIL)
Wh\fn th\f ignition switch is in th\f “\bN” position, th\f
Malfunction Indicator Light (MIL) illuminat\fs. Aft\fr
starting th\f \fngin\f, th\f MIL turns off. This indicat\fs
that th\f \fngin\f control syst\fm is op\frational.
If th\f MIL illuminat\fs or blinks (if \fquipp\fd) whil\f th\f
\fngin\f is running, it may indicat\f that th\f \fngin\f
control syst\fm is not functioning prop\frly and may
n\f\fd s\frvicing. Hav\f th\f syst\fm ch\fck\fd, and if
n\fc\fssary r\fpair\fd, by a RENAULT d\fal\fr promptly.
Malfunction Indicator Light (MIL) on steady:
An \fngin\f control syst\fm malfunction has b\f\fn
d\ft\fct\fd. Hav\f th\f v\fhicl\f ch\fck\fd, and if n\fc\fssary
r\fpair\fd, by a RENAULT d\fal\fr promptly. You do not
n\f\fd to hav\f your v\fhicl\f tow\fd to th\f d\fal\fr.
Malfunction Indicator Light (MIL) blinking (if
equipped):
An \fngin\f misfir\f has b\f\fn d\ft\fct\fd which may
damag\f th\f \fngin\f control syst\fm. Hav\f th\f v\fhicl\f
ch\fck\fd, and if n\fc\fssary r\fpair\fd, by a RENAULT
d\fal\fr promptly.
To r\fduc\f or avoid possibl\f damag\f to th\f \fngin\f
control syst\fm wh\fn th\f MIL illuminat\fs or blinks:
.Avoid driving at sp\f\fds abov\f 70 km/h (43 MPH) .
. Avoid sudd\fn acc\fl\fration or d\fc\fl\fration.
. Avoid going up st\f\fp uphill grad\fs.
. Avoid carrying or towing unn\fc\fssary loads.
CAUTION:
.Continuing vehicle operation without proper
servicing of the engine control system could
lead to poor driveability, reduced fuel econ-
omy, and damage to the engine control system, which may affect the vehicle’s
warranty coverage.
. Incorrect setting of the engine control sys-
tem may lead to non-compliance of local
and national emission laws and regulations.
\bv\frdriv\f off indicator light (if
\fquipp\fd)
Th\f ov\frdriv\f off indicator light illuminat\fs wh\fn th\f
ov\frdriv\f is turn\fd \bFF. (S\f\f “Driving with Automatic
Transmission (AT)” (P.5-11) for th\f us\f of th\f ov\frdriv\f
off switch.)
R\far fog light indicator light (if
\fquipp\fd)
Th\f r\far fog light indicator light illuminat\fs wh\fn th\f
r\far fog light is on. (S\f\f “Fog light switch” (P.2-32) .)
S\fcurity indicator light (if \fquipp\fd)
Th\f s\fcurity indicator light blinks wh\fn th\f ignition
switch is in th\f “L\bCK”, “\bFF” or “ACC” position. This
function indicat\fs th\f Anti-Th\fft Syst\fm* \fquipp\fd on
th\f v\fhicl\f is op\frational.
(* immobiliz\fr)
If Anti-Th\fft Syst\fm is malfunctioning, this light will
r\fmain on whil\f th\f ignition switch is in th\f “\bN”
position. (S\f\f “S\fcurity syst\fm” (P.3-16) for additional
information.)
Slip indicator light (if \fquipp\fd)
Wh\fn th\f ignition switch is in th\f “\bN” position, th\f
slip indicator light illuminat\fs and th\fn turns off. This
indicat\fs that th\f V\fhicl\f Dynamic Control (VDC)
syst\fm or El\fctronic Stability Program (ESP) syst\fm is
op\frational.
Th\f slip indicator light blinks wh\fn th\f VDC or ESP
syst\fm is op\frating.
Wh\fn th\f indicator light blinks whil\f driving, th\f driving
condition is slipp\fry and th\f v\fhicl\f’s traction limit is
about to b\f \fxc\f\fd\fd.
If th\f VDC or ESP off indicator light and slip indicator
light illuminat\f whil\f th\f \fngin\f is running or whil\f
driving, it may indicat\f that th\f VDC or ESP syst\fm is
not functioning prop\frly and may n\f\fd s\frvicing. Hav\f
th\f syst\fm ch\fck\fd, and if n\fc\fssary r\fpair\fd, by a
RENAULT d\fal\fr promptly. (S\f\f “V\fhicl\f Dynamic
Control (VDC) syst\fm (if \fquipp\fd \fxc\fpt for Europ\f)”
(P.5-24) or “El\fctronic Stability Program (ESP) Syst\fm
(if \fquipp\fd for Europ\f)” (P.5-25) .)
Sp\f\fd limit\fr indicator light (if
\fquipp\fd)
This light illuminat\fs wh\fn th\f sp\f\fd limit\fr main
switch is push\fd. Th\f light turns off wh\fn th\f main
switch is push\fd again. Wh\fn th\f sp\f\fd limit\fr main
switch indicator light illuminat\fs, th\f sp\f\fd limit\fr
syst\fm is op\frational. (S\f\f “Sp\f\fd limit\fr (if \fquipp\fd
for Europ\f)” (P.5-26) .)
Instruments and controls2-17
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
2-30Instruments and controls
position
Theposition turns on the headlights in addition to
the other lights\f
Headlight beam
\bIC3785
To turn on the high beam, push the lever towards the
front position*1\f
To turn off the high beam, return the lever to the neutral
position
*2\f
To flash the headlights, pull the lever towards the
rearmost position
*3\f The headlights can be flashed
even when the headlights are not on\f If equipped, when the lever is pulled towards the
rearmost position
*3after the ignition switch is
placed in the “OFF” or “LOCK” position, the headlight
will turn on and stay on for 30 seconds\f The lever can
be pulled 4 times for up to 2 minutes\f
Daytime light system (if equipped)
Even if the headlight switch is off, the daytime lights
will come on after starting the engine\f However, you
cannot change low beam to high beam when the light
switch is off\f
When the light switch is turned to the
position,
the headlight low beam will turn off\f
BATTERY \bAVER \bY\bTEM
The light reminder chime will sound if the driver’s door
is opened while the following improper operations
occur:
. The headlight switch is in either the
orposition, and the ignition switch in the “ACC”,
“OFF” or “LOCK” position\f
. The headlight switch is in the “AUTO” position and
the front or rear fog light (if equipped) is turned on
while the ignition switch is in the “ACC”, “OFF” or
“LOCK” position\f
Be sure to turn the headlight switch to the “OFF”
position when you leave the vehicle\f
Type A
When the headlight switch is in the
orposition while the engine is running, the lights will
automatically turn off after pushing the ignition switch
to the “ACC”, “OFF” or “LOCK” position and opening
the driver’s side door\f
When the headlight switch remains in either the
orposition after the lights automatically turn off,
the lights will turn on when the engine is started\f Type B
If the doors are closed and locked with the remote
controller, the Intelligent Key or the door request
switch (if equipped) while the headlight switch is in
either the
orposition, the battery saver
function will turn off the lights to prevent the battery
from being discharged\f The lights will turn on when the
doors are being opened\f
CAUTION:
Do not leave the lights on when the engine is not
running for extended periods of time to prevent
the battery from being discharged.
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
HEADLIGHT AIMING CONTROL (if
equi\f\fed)
Ma\bual ty\fe
SIC2275
The headlight aimi\bg co\btrol o\ferates whe\b the
ig\bitio\b switch is i\b the “ON” \fositio\b a\bd the headlight
is o\b to allow the headlight axis to be adjusted
accordi\bg to the drivi\bg co\bditio\b.
Whe\b drivi\bg with \bo heavy load/luggage or drivi\bg o\b
a flat road, select the \bormal \fositio\b “0”.
If the \bumber of occu\fa\bts a\bd load/luggage i\b the
vehicle cha\bges, the headlight axis may become higher
tha\b \bormal.
If the vehicle is traveli\bg o\b a hilly road, the headlights
may directly shi\be o\b the rearview a\bd outside mirrors
of a vehicle ahead or the wi\bdshield of a\b o\bcomi\bg
vehicle, which may obscure other drivers’ visio\b.
To adjust to the \fro\fer aimi\bg height, tur\b the switch
accordi\bgly. The higher the \bumber, desig\bated o\b the
switch, the lower the headlight axis.
Select the switch \fositio\b by referri\bg to the followi\bg
sam\fles.
Switch \fo-sitio\b Number of
fro\bt seat
occu\fa\bts Number of
rear seat
occu\fa\bts Weight of load i\b lug-
gage com\fartme\bt
0 1 or 2 No occu-
\fa\bts No load
1 2 3 No load
22 3 A\f\froximately 48 kg
(106 lb)
31 No occu-
\fa\bts A\f\froximately 279 kg
(615 lb)
TURN SIGNAL SWITCH
SIC3786
CAUTION:
The turn signal switch will not be cancelled
automatically if the steering wheel turning angle
does not exceed the preset amount. After the
turn or lane change, make sure that the turn
signal switch is returned to its original position.
Tur\b sig\bal
To tur\b o\b the tur\b sig\bals, move the lever u\f*1or
dow\b*2towards the desired directio\b. Whe\b the
tur\b is com\fleted, the tur\b sig\bal ca\bcels automati-
cally.
La\be cha\bge sig\bal
To tur\b o\b the la\be cha\bge sig\bals, move the lever u\f*1or dow\b*2towards the desired directio\b.
If the lever is moved back right after movi\bg u\f
*1or
dow\b*2, the light will flash 3 times (if equi\f\fed) .
To ca\bcel the flashi\bg, move the lever to the o\f\fosite
directio\b.
Instruments and controls2-31
&RQGLWLRQ


> (GLW    0RGHO .$2(0B5HQDXOW @
WARNING:
In freezing temperatures, the washer fluid may
freeze on the windshield and obscure your
vision. Warm the windshield with the defogger
before you wash the windshield.
CAUTION:
.Do not operate the washer continuously for
longer than 30 seconds.
. Do not operate the washer if the window
washer fluid reservoir is empty.
WINDSHIELD WIPER AND WASHER
SWITCH
JVI0271\fType A (example)
JVI0034\fType B (example)Th\b windshi\bld wip\br and wash\br op\brat\b wh\bn th\b
ignition switch is in th\b “ON” position.
Wip\br op\bration
Th\b l\bv\br position “INT” or “”*1op\brat\bs th\b
wip\br int\brmitt\bntly.
. If \bquipp\bd, th\b int\brmitt\bnt op\bration can b\b
adjust\bd by turning th\b adjustm\bnt control knob,
(long\br)
*Aor (short\br)*B.
. If \bquipp\bd, th\b sp\b\bd of th\b int\brmitt\bnt op\bra-
tion vari\bs d\bp\bnding on th\b v\bhicl\b sp\b\bd.
Th\b l\bv\br position “AUTO”
*1op\brat\bs th\b rain
s\bnsing auto wip\br syst\bm (if \bquipp\bd) . (S\b\b “Rain-
s\bnsing auto wip\br syst\bm” (P.2-33) .)
Th\b l\bv\br position “LO” or “
”*2op\brat\bs th\b
wip\br at low sp\b\bd.
Th\b l\bv\br position “HI” or “
”*3op\brat\bs th\b
wip\br at high sp\b\bd.
To stop th\b wip\br op\bration, mov\b th\b l\bv\br up to th\b
“OFF” position.
Th\b l\bv\br position “MIST” or “
”*4op\brat\bs th\b
wip\br on\b sw\b\bp. Th\b l\bv\br automatically r\bturns to its
original position. If the windshield wiper operation is interrupted
by snow etc., the wiper may stop moving to
protect its motor. If this occurs, turn the wiper
switch to OFF and remove the snow etc. on and
around the wiper arms. In approximately 20
seconds, turn the switch ON again to operate
the wiper.
Wash\br op\bration
To op\brat\b th\b wash\br, pull th\b l\bv\br toward th\b back
of th\b v\bhicl\b*5until th\b d\bsir\bd amount of wash\br
fluid is spr\bad on th\b windshi\bld. Th\b wip\br will
automatically op\brat\b s\bv\bral tim\bs.
RAIN-SENSING AUTO WIPER SYSTEM (if
\bquipp\bd)
SIC4018Type A
Instruments and controls2-33
WIPER AND WASHER SWITCH
&RQGLWLRQ