navigation RENAULT SCENIC 2008 J84 / 2.G Multimedia ITS User Guide

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 19V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04
DF023
CONTINUED
2.DEF
NOTESNone
Check the condition and connection of the display connector (component code 1127) and of the navigation
computer 32-track connector (component code 662) (broken, oxidised, bent tabs).
Manipulate the wiring harness at the connectors to produce a change in fault status (present → stored).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code TB30,
●connection code TB31,
●connection code 34HA,
●connection code 34GZ,
●connection code 34HU,
between components 662 and 1127.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 20V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04
DF025
PRESENT
OR
STOREDNO CENTRAL CONTROL MULTIPLEX SIGNAL
1.DEF : No communication with the central control
NOTESConditions for applying fault finding procedures to stored faults:
Apply this fault finding procedure if the fault reappears as present or stored after the
fault has been cleared, the ignition switched off and back on again and the navigation
system started after using the central control several times.
If faults DF022 No radio multiplex signal, DF025 No central control multiplex
signal and DF027 No audio CD changer signals are present at the same time, check
the multimedia network (see 88B, Multiplexing).
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition and connection of the navigation central control connector (component code 1657) and of the
navigation computer 32-track connector (component code 662) (broken, oxidised, bent tabs).
Manipulate the wiring harness at the connectors to produce a change in fault status (present → stored).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
With ignition on, check for + 12 V on the BCP3 connection of component 1657.
Check that the earth on the MX connection on the component 1657 connector is perfect.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code 34DZ,
●connection code 34GA,
●connection code 34HU,
between components 1657 and 662.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
ITS_V04_DF025ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 22V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04
DF029
PRESENT
OR
STOREDREADING NAVIGATION DVD
1.DEF : Disc cannot be read
NOTESConditions for applying fault finding procedures to stored faults:
Apply this fault finding procedure if the fault reappears as present or stored after the
fault has been cleared, the ignition switched off and back on again and the navigation
system started with a navigation DVD in good condition.
Check that the DVD is inserted the right way up.
Check that the DVD in the navigation computer is not an audio CD or other type but a navigation DVD designed
for this navigation system.
Wipe the DVD from the centre out with a soft, clean cloth.
Replace the navigation DVD if it is scratched.
If the fault is still present after the DVD has been changed, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
ITS_V04_DF029ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of faults
86C
86C - 23V5 MR-372-J84-86C050$468.mif
ITS
Program No.: 0020
Vdiag No.: 04
DF030
PRESENT
OR
STOREDGPS AERIAL CIRCUIT
CO : Open circuit
NOTESConditions for applying the fault finding procedure to the stored fault:
Apply this fault finding procedure if the fault reappears as present or stored after it has
been cleared and the ignition has been switched off and on again.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition and connection of the GPS aerial 2-track connectors (component code 886) and of the
navigation computer (component code 662) (broken, oxidised, bent tabs).
Manipulate the wiring harness at the connectors to produce a change in status (present → stored).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code 46CB,
●connection code TB15,
between components 662 and 886.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the connections are correct, replace the GPS aerial.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
ITS_V04_DF030ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Conformity check
86C
86C - 27V5 MR-372-J84-86C050$520.mif
ITS
Program no.: 0020
Vdiag No.: 04
Sub-function: TESTS
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application conditions: Engine stopped, + after ignition feed switched on.
Order FunctionParameter or Status
Check or Action Display and Notes Fault finding
1ScreenAC006:Screen test:
colour barsThis command is used
to test the colour
connections between
the navigation
computer and the
display.In the event of a fault, apply
the interpretation of
command AC006 Screen
test: colour bars.
AC007:Screen test:
shades of greyThis command is used
to test the video
connections between
the navigation
computer and the
display.In the event of a fault, apply
the interpretation of
command AC007 Screen
test: gradation of grey.
AC008:Screen test:
white screenThis command is used
to test the screen to
see if a pixel from the
display is out of order.Replace the display if several
pixels are out of order.
2Microphone AC009:Microphone testThis command is for
testing microphone
operation.
Note:
If it is quiet, speak into
the microphone to
check that it is working.In the event of a fault, apply
the interpretation of
command
AC009 Microphone test.
ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of statuses
86C
86C - 29V5 MR-372-J84-86C050$624.mif
ITS
Program no.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Interpretation of statuses
ET003
+ 12 V SIDE LIGHTS FEED
NOTESVisually check that the side lights are working. Carry out fault finding on the steering
column switches and the side lights.
Use the Wiring Diagrams Technical Note, Scenic II.
Check the condition of the 7.5 A fuse in the engine compartment connection unit (component code 1337).
Check the condition and connection of the navigation central control connectors (component code 1657) and of
the CD changer (component code 1272) (broken, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the LPG connection between
components 1337, 1272 and 1657.
If the connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
ITS_V04_ET003ITSJ84ph2V1.0
MR-372-J84-86C050$624.mif

MULTIMEDIA
Fault finding - Interpretation of statuses
86C
86C - 34V5 MR-372-J84-86C050$624.mif
ITS
Program no.: 0020
Vdiag No.: 04
ET024
REVERSE GEAR ENGAGED
NOTESThere must be no present or stored faults.
Use the Wiring Diagrams Technical Note, Scenic II.
Carry out fault finding on the Protection and Switching Unit (see 87G, Engine compartment connection unit).
Check the condition and connection of the navigation computer 32-track connector (component code 662) (broken,
oxidised, bent tabs).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the Protection and Switching Unit MN and CN connectors (Vdiag 48)
(component code 1337) (broken, oxidised, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance of the H66P connection between
components 662 and 1337.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
ITS_V04_ET024ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of commands
86C
86C - 38V5 MR-372-J84-86C050$832.mif
ITS
Program no.: 0020
Vdiag No.: 04MULTIMEDIA
Fault finding - Interpretation of commands
RZ001 Fault memory:
This command is used to clear faults stored in the navigation computer.
RZ002 Computer memory:
This command enables the configuration CF001 Vehicle Type for the navigation computer to be removed.
RZ003 Customer parameters and data
This command is used to clear CF001 Vehicle type command configurations, address books and navigation
settings stored by the customer in the navigation computer.
This command is also used to clear telephone numbers stored in the navigation computer and the list of received and
dialled calls when the telephone is connected to the vehicle.
Clearing procedure
●Establish dialogue with the navigation computer.
●Select the Repair mode menu.
●Select the Clear menu.
●Select the line of your choice.
●Confirm.
VP002 Write VIN:
This command permits manual entry of the vehicle's VIN into the computer. Use this command each time the
computer is replaced. The VIN number is inscribed on the manufacturer's plate.
Procedure for writing the VIN
●Establish dialogue with the navigation computer.
●Select the Repair mode menu.
●Select the other parameters menu.
●Select line VP002 Write VIN.
●Enter the VIN.
●Exit fault finding mode.
●Switch off the ignition.
●Wait for the end of the power-latch.
●Read the VIN again from the Identification menu for confirmation. IMPORTANT
The NETHERLANDS configuration is IRREVERSIBLE this selection cannot be cleared.
IMPORTANT
This command must be activated before removing the computer.
ITSJ84ph2V1.0
MR-372-J84-86C050$832.mif

MULTIMEDIA
Fault finding - Interpretation of commands
86C
86C - 40V5 MR-372-J84-86C050$832.mif
ITS
Program no.: 0020
Vdiag No.: 04
AC006
SCREEN TEST: COLOUR BARS
NOTESThere must be no present or stored faults.
Use the Wiring Diagrams Technical Note, Scenic II.
Apply this procedure if one or more colour bars is missing on the display when this command is run.
Check the condition and connection of the display connector (component code 1127) and of the navigation
computer 32-track connector (component code 662) (broken, oxidised, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check for + 12 V on connection BCP3 of the component 1127 connector.
Check that the earth on connection 34GU of the component 1127 connector is perfect.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code TB31,
●connection code 34DD,
●connection code 34DC,
●connection code 34DB,
●connection code 34GU,
between components 1127 and 662.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the checks reveal no faults, but the colours displayed by component 1127 are incorrect, replace
component 1127.
AFTER REPAIRCarry out another fault finding check on the system.
ITSJ84ph2V1.0

MULTIMEDIA
Fault finding - Interpretation of commands
86C
86C - 41V5 MR-372-J84-86C050$832.mif
ITS
Program no.: 0020
Vdiag No.: 04
AC007
SCREEN TEST: GRADATION OF GREY
NOTESThere must be no present or stored faults.
Use the Wiring Diagrams Technical Note, Scenic II.
Apply this procedure if the shade of grey shown on the display when the command is activated is incorrect.
Check the condition and connection of the display connector (component code 1127) and of the navigation
computer 32-track connector (component code 662) (broken, oxidised, bent tabs).
If the connectors are faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connectors; otherwise, replace the wiring.
Check that the earth on connection 34GU of the component 1127 connector is perfect.
If the connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Check that the earth on the MAN connection of component 1127 is perfect.
Check for + 12 V on connection BCP3 of the component 1127 connector.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●connection code TB30,
●connection code 34HA,
●connection code 34GZ,
between components 1127 and 662.
If any connection is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring; otherwise, replace the wiring.
If the checks reveal no faults, but the gradation of grey displayed by the display is not correct, replace
component 1127.
AFTER REPAIRCarry out another fault finding check on the system.
ITSJ84ph2V1.0