air conditioning RENAULT SCENIC 2008 J84 / 2.G Passenger Comparment Connection Unit User Guide

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -129
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -129V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: AIR CONDITIONING
Sub-function: Cold Loop
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
Cold loopET030:Air conditioning
request 2ACTIVE
INACTIVEIn the event of a fault,
consult the
interpretation of status
ET030.
ET169:EngineSTOPPEDIn the event of a fault,
refer to the
interpretation of
status ET169.
ET015:Passenger
compartment fan ACTIVE
INACTIVE
Note:
This status is only operative
for manual air conditioning
systems (and heater versions
without air conditioning). In the event of a fault,
refer to the
interpretation of status
ET015.
PR002:External
temperature Temperature in ˚CIn the event of a fault,
consult the
interpretation of
parameter PR002.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -139
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -139V9 MR-372-J84-87B000$430.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
*RCH = Passenger Compartment Heating ResistorTool status Diagnostic tool title Vdiag
ET008UCH blankV44, V48, V4C,
V4D, V4F, V50
ET010Card frequency (in MHz)V44, V48, V4C,
V4D
ET014Control power level
V44, V48, V4C,
V4D, V4F, V50 ET015Passenger compartment fan
ET016Buzzer activation request
ET017Number of RCH* required
ET018Number of RCH* authorised by alternator
ET019Number of RCH* authorised by injection computer
ET020Number RCH* activated.
ET021RCH* 1 relay control
ET022RCH* 2 relay control
ET023RCH* 3 relay control
ET025Retractable roof V48, V4C, V4D,
V4F, V50
ET026Heated rear screen switch
V44, V48, V4C,
V4D, V4F, V50 ET028Heated rear screen button
ET029Air conditioning button
ET030Air conditioning request 2
ET031Fast idle speed request for RCH*
ET032Front left-hand wheel valve signal
ET033Front right-hand wheel valve signal
ET034Rear right-hand wheel valve signal
ET035Rear left-hand wheel valve signal
ET038Service warning light on request
ET039STOP warning light on request
ET040Tyre pressure monitoring system
MR-372-J84-87B000$430.mif

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -145
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -145V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET015
PASSENGER COMPARTMENT FAN
NOTESThere must be no present or stored faults.
Apply to manual air conditioning and heating systems.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
ET015 is Inactive, the ventilation control on the air conditioning control panel is not 0.
Check the condition and connection of the heating and air conditioning system control panel connector (bent,
broken tabs, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the UCH connector PE2 (tabs bent, broken, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the continuity and insulation of the following connections:
●Connection code 38LP,
●Connection code 38LQ,
between components 645 and 319.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the control panel (see 62C, Manual air conditioning).
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET015/UCH_V48_ET015/ UCH_V4C_ET015/
UCH_V4D_ET015 /UCH_V4F_ET015/UCH_V50_ET015

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -147
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -147V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
*RCH = Passenger Compartment Heating ResistorET017
NUMBER OF RCH* REQUIRED
NOTESThere must be no present or stored faults.
The status, depending on the conditions, will be 0, 1, 2, 3, 4 or 5.
Special note:
Manual air conditioning (not automatic)
Defined by the UCH according to the engine coolant temperature, the external
temperature and electrical availability.
Climate control
Defined by the UCH according to the engine coolant temperature, the external
temperature, electrical availability, the internal temperature and the user's request.
The passenger compartment heating resistor control conditions are:
Manual air conditioning (not automatic):
ET169 Engine is Running,
ET015 Passenger compartment fan Active,
PR002 Exterior temperature < 5˚C
Engine coolant temperature < 50˚C (refer to injection computer),
Electrical availability - 60%, alternator load < 70% (refer to the Power and Switching Unit).
Climate control:
ET169 Engine is Running,
PR002 Exterior temperature < 5˚C
Engine coolant temperature < 50˚C (refer to injection computer).
Electrical availability - 60%, alternator charge < 70% (refer to the Power and Switching Unit).
Heat demand by the user (refer to the climate control computer).
Check the consistency of these statuses and parameters.
In the event of a fault, consult the interpretation of these statuses and parameters.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET017/UCH_V48_ET017/ UCH_V4C_ET017/
UCH_V4D_ET017 /UCH_V4F_ET017/UCH_V50_ET017

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -150
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -150V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
*RCH = Passenger Compartment Heating ResistorET020
NUMBER OF RCH* CONTROLLED
NOTESThere must be no present or stored faults.
The maximum number of passenger compartment heating resistors controlled will be
the minimum number indicated by statuses ET017, ET018, ET019.
Special note:
The UCH controls the passenger compartment heating resistor relays according to the
authorisation from the injection computers and Protection and Switching Unit.
The status, depending on the conditions, will be 0, 1, 2, 3, or 4.
The passenger compartment heating resistor control conditions are:
–Heater motor running.
–Battery voltage > 12 V.
–Interior temperature < 10˚C.
–User temperature setpoint in warm position (> 20˚C).
–PR002 External temperature < 5˚C.
–ET015 Passenger compartment fan ACTIVE.
–ET018 Number of RCHs authorised by alternator > 0.
–ET019 Number of RCH* authorised by injection computer > 0.
–PR010 (UPC) Alternator charge < 70%.
If all the conditions are satisfied, and depending on the air conditioning function program, the UCH controls the
Passenger Compartment Heating Resistors needed to provide the service.
Check that these statuses and parameters are working properly.
In the event of a fault, refer to the interpretation of these statuses and parameters.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET020/UCH_V48_ET020/ UCH_V4C_ET020/
UCH_V4D_ET020 /UCH_V4F_ET020/UCH_V50_ET020

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -153V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET026
HEATED REAR SCREEN CONTROL
NOTESThere must be no present or stored faults.
Special note:
Operation of the heated rear screen requires the engine status to be Running.
ET026 Inactive despite a rear de-icing request by the user.
Air conditioning
Manual
Climate control
Verify that status ET142 Engine operating phase is Running; otherwise, carry out
fault finding on the injection system.
Check that status ET028 Heated rear screen switch is PRESSED, otherwise refer
to the interpretation of this status.
If the fault is still present, contact your Techline.
Verify that status ET142 Engine operating phase is Running; otherwise, carry out
fault finding on the injection system.
If the fault is still present, carry out a fault finding procedure on the air conditioning
computer.
If the fault is still present, contact your Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET026/UCH_V48_ET026/ UCH_V4C_ET026/
UCH_V4D_ET026 /UCH_V4F_ET026/UCH_V50_ET026

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -154
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -154V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET028
HEATED REAR SCREEN BUTTON
NOTESThere must be no present or stored faults.
Special note:
Information interpretable if the vehicle is configured with Heating or Manual Air
Conditioning (SC008 UCH type and CF019 Type of air conditioning).
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
ET028 Released with press on the button.
ET028 Pressed without press on the button.
Check the condition and connection of the air conditioning control panel connector (bent, broken tabs, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the UCH connector PE2 (tabs bent, broken).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 15M between components 645 and 139.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the control panel (see 62C, Manual air conditioning).
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET028/UCH_V48_ET028/ UCH_V4C_ET028/
UCH_V4D_ET028 /UCH_V4F_ET028/UCH_V50_ET028

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -155
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -155V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET029
AIR CONDITIONING BUTTON
NOTESThere must be no present or stored faults.
Special note:
Information interpretable if the vehicle is configured with Manual Air
Conditioning (SC008 UCH type and CF019 Type of air conditioning).
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check the condition and connection of the air conditioning control panel connector (bent, broken tabs, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the UCH connector PE2 (tabs bent, broken).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 38AL between components 645 and 319.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the control panel (see 62C, Manual air conditioning).
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET029/UCH_V48_ET029/ UCH_V4C_ET029/
UCH_V4D_ET029 /UCH_V4F_ET029/UCH_V50_ET029

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -156V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET030
AIR CONDITIONING REQUEST 2
NOTESThere must be no present or stored faults.
The engine must be running.
Special note:
This is the request for air conditioning sent by the UCH to the injection computer. This
request may reach the UCH in two ways:
–In the case of a vehicle fitted with manual air conditioning, by pressing on the air
conditioning button.
–In the case of a vehicle fitted with climate control, by request from the user or the
climate control computer in automatic mode.
ET030 Inactive despite a climate control request.
Air conditioning
Manual

Air conditioning
climate control
Verify that status ET169 Engine is Running. If status ET169 is not running, run fault
finding on the injection.
Check that status ET029 Air conditioning button is PRESSED by pressing the
button. If status ET029 is RELEASED carry out fault finding on this status.
Verify that status ET015 Passenger compartment ventilation is ACTIVE. If status
ET015 is INACTIVE carry out fault finding on this status.
If the fault is still present, contact the Techline.
Carry out fault finding on the climate control computer (see 62C, Manual air
conditioning).
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET030/UCH_V48_ET030/ UCH_V4C_ET030/
UCH_V4D_ET030 /UCH_V4F_ET030/UCH_V50_ET030

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Command summary table87B
87B - 246
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Command summary table87B
87B - 246V9 MR-372-J84-87B000$731.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Command summary table
*RCH: Passenger Compartment Heating Resistor
*CPE: Electric central door locking
*SR.: SunroofTool command Diagnostic tool title Vdiag
AC003Immobiliser warning light
V44, V48,
V4C, V4D,
V4F, V50 AC004Central door locking
AC005Central door unlocking
AC006Driver's door unlocking
AC007Rear screen wiper
AC008Front fog lights
AC009Rear fog lights
AC015Air conditioning button indicator light
AC016RCH* 1 relay
AC017RCH* 2 relay
AC018RCH* 3 relay
AC019Heated rear screen indicator light
AC020CPE* button indicator light
AC021Interior lights
AC022Left-hand direction indicator
AC023Right-hand direction indicator
AC024Card reader lighting
AC025One-touch window control/SR.* authorisation
AC026Start button lighting
AC027Footwell lights
AC030Headlight washer relay 1 (only if Vdiag 44 UPC)
AC031Headlight washer relay 2 (only if Vdiag 44 UPC)
AC032Driver's side external aerial testing
AC033Passenger's side external aerial testing
AC034Boot external aerial test
AC036Internal aerial test
AC037Transmitter aerial fault finding
AC076Child safety lock indicator light
MR-372-J84-87B000$731.mif