heating RENAULT SCENIC 2008 J84 / 2.G Passenger Comparment Connection Unit User Guide

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -139
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -139V9 MR-372-J84-87B000$430.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
*RCH = Passenger Compartment Heating ResistorTool status Diagnostic tool title Vdiag
ET008UCH blankV44, V48, V4C,
V4D, V4F, V50
ET010Card frequency (in MHz)V44, V48, V4C,
V4D
ET014Control power level
V44, V48, V4C,
V4D, V4F, V50 ET015Passenger compartment fan
ET016Buzzer activation request
ET017Number of RCH* required
ET018Number of RCH* authorised by alternator
ET019Number of RCH* authorised by injection computer
ET020Number RCH* activated.
ET021RCH* 1 relay control
ET022RCH* 2 relay control
ET023RCH* 3 relay control
ET025Retractable roof V48, V4C, V4D,
V4F, V50
ET026Heated rear screen switch
V44, V48, V4C,
V4D, V4F, V50 ET028Heated rear screen button
ET029Air conditioning button
ET030Air conditioning request 2
ET031Fast idle speed request for RCH*
ET032Front left-hand wheel valve signal
ET033Front right-hand wheel valve signal
ET034Rear right-hand wheel valve signal
ET035Rear left-hand wheel valve signal
ET038Service warning light on request
ET039STOP warning light on request
ET040Tyre pressure monitoring system
MR-372-J84-87B000$430.mif

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -145
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -145V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET015
PASSENGER COMPARTMENT FAN
NOTESThere must be no present or stored faults.
Apply to manual air conditioning and heating systems.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
ET015 is Inactive, the ventilation control on the air conditioning control panel is not 0.
Check the condition and connection of the heating and air conditioning system control panel connector (bent,
broken tabs, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the UCH connector PE2 (tabs bent, broken, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the continuity and insulation of the following connections:
●Connection code 38LP,
●Connection code 38LQ,
between components 645 and 319.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the control panel (see 62C, Manual air conditioning).
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET015/UCH_V48_ET015/ UCH_V4C_ET015/
UCH_V4D_ET015 /UCH_V4F_ET015/UCH_V50_ET015

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -147
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -147V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
*RCH = Passenger Compartment Heating ResistorET017
NUMBER OF RCH* REQUIRED
NOTESThere must be no present or stored faults.
The status, depending on the conditions, will be 0, 1, 2, 3, 4 or 5.
Special note:
Manual air conditioning (not automatic)
Defined by the UCH according to the engine coolant temperature, the external
temperature and electrical availability.
Climate control
Defined by the UCH according to the engine coolant temperature, the external
temperature, electrical availability, the internal temperature and the user's request.
The passenger compartment heating resistor control conditions are:
Manual air conditioning (not automatic):
ET169 Engine is Running,
ET015 Passenger compartment fan Active,
PR002 Exterior temperature < 5˚C
Engine coolant temperature < 50˚C (refer to injection computer),
Electrical availability - 60%, alternator load < 70% (refer to the Power and Switching Unit).
Climate control:
ET169 Engine is Running,
PR002 Exterior temperature < 5˚C
Engine coolant temperature < 50˚C (refer to injection computer).
Electrical availability - 60%, alternator charge < 70% (refer to the Power and Switching Unit).
Heat demand by the user (refer to the climate control computer).
Check the consistency of these statuses and parameters.
In the event of a fault, consult the interpretation of these statuses and parameters.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET017/UCH_V48_ET017/ UCH_V4C_ET017/
UCH_V4D_ET017 /UCH_V4F_ET017/UCH_V50_ET017

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -148
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -148V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
*RCH = Passenger Compartment Heating ResistorET018
NUMBER OF RCH* AUTHORISED BY ALTERNATOR
NOTESThere must be no present or stored faults.
Special note:
This information is usable only on vehicles fitted with passenger compartment heating
resistors.
Calculation performed by the UCH according to the alternator power available
(information supplied by the UPC).
This information allows the number of passenger compartment heating resistors to be
supplied depending on the available power.
The status, depending on the conditions, will be 0, 1, 2, 3, 4 or 5.
In the event of a fault, perform fault finding on the UPC (see 87G, Engine compartment connection unit).
The parameter PR010 (UPC) of the alternator charge should be less than 70% so that the passenger
compartment heating resistors can be authorised by the alternator.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET018/UCH_V48_ET018/ UCH_V4C_ET018/
UCH_V4D_ET018 /UCH_V4F_ET018/UCH_V50_ET018

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -149
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -149V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
*RCH = Passenger Compartment Heating ResistorET019
NUMBER OF PASSENGER COMPARTMENT HEATING
RESISTORS AUTHORISED BY THE INJECTION
NOTESThere must be no present or stored faults.
Special note:
Calculation performed by the UCH depending on the maximum power authorised by
the injection computer.
This information allows the number of passenger compartment heating resistors to be
supplied depending on the engine load.
The status, depending on the conditions, will be 0, 1, 2, 3, 4 or 5.
In the event of a fault, run fault finding on the injection system (see 13B, Diesel injection or 17B, Petrol injection).
Conditions for authorisation of passenger compartment heating resistor by the injection:
–the injection system status ET111 Fixed number of RCH* should be NO,
–the injection system status ET112 RCH* cut-off should be NO.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET019/UCH_V48_ET019/ UCH_V4C_ET019/
UCH_V4D_ET019 /UCH_V4F_ET019/UCH_V50_ET019

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -150
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -150V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
*RCH = Passenger Compartment Heating ResistorET020
NUMBER OF RCH* CONTROLLED
NOTESThere must be no present or stored faults.
The maximum number of passenger compartment heating resistors controlled will be
the minimum number indicated by statuses ET017, ET018, ET019.
Special note:
The UCH controls the passenger compartment heating resistor relays according to the
authorisation from the injection computers and Protection and Switching Unit.
The status, depending on the conditions, will be 0, 1, 2, 3, or 4.
The passenger compartment heating resistor control conditions are:
–Heater motor running.
–Battery voltage > 12 V.
–Interior temperature < 10˚C.
–User temperature setpoint in warm position (> 20˚C).
–PR002 External temperature < 5˚C.
–ET015 Passenger compartment fan ACTIVE.
–ET018 Number of RCHs authorised by alternator > 0.
–ET019 Number of RCH* authorised by injection computer > 0.
–PR010 (UPC) Alternator charge < 70%.
If all the conditions are satisfied, and depending on the air conditioning function program, the UCH controls the
Passenger Compartment Heating Resistors needed to provide the service.
Check that these statuses and parameters are working properly.
In the event of a fault, refer to the interpretation of these statuses and parameters.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET020/UCH_V48_ET020/ UCH_V4C_ET020/
UCH_V4D_ET020 /UCH_V4F_ET020/UCH_V50_ET020

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -151
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -151V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
*RCH = Passenger Compartment Heating ResistorET021
ET022
ET023
RCH* 1 RELAY CONTROL
RCH* 2 RELAY CONTROL
RCH* 3 RELAY CONTROL
NOTESThere must be no present or stored faults.
For statuses ET021 and ET022, the signal can be interpreted if the vehicle is
configured with 1000 W Passenger Compartment Heating Resistors or 1800 W
Passenger Compartment Heating Resistors.
For status ET023, the signal is interpretable if the vehicle is configured with RCH
1800 W.
In the event of a fault, check the operation of statuses ET015 Passenger compartment fan, ET017 Number of
RCH* required, ET018 Number of RCH* authorised by alternator, ET019 Number of RCH* authorised by
injection and ET020 Number of RCH* controlled.
Carry out fault finding on commands AC016 RCH* relay 1, AC017 RCH* relay 2 and AC018 RCH* relay 3.
Check the parameters needed to switch on the Passenger Compartment Heating Resistors; exterior temperature,
interior temperature, temperature setpoint on the heater control panel, alternator load, battery voltage.
If all the requisite conditions are consistent and the status remains INACTIVE, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET021/UCH_V48_ET021/ UCH_V4C_ET021/UCH_V4D_ET021/ UCH_V4F_ET021/UCH_V50_ET021/
UCH_V44_ET022/UCH_V48_ET022/ UCH_V4C_ET022/UCH_V4D_ET022/ UCH_V4F_ET022/UCH_V50_ET022/
UCH_V44_ET023/UCH_V48_ET023/ UCH_V4C_ET023/UCH_V4D_ET023/ UCH_V4F_ET023/UCH_V50_ET023

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -154
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -154V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET028
HEATED REAR SCREEN BUTTON
NOTESThere must be no present or stored faults.
Special note:
Information interpretable if the vehicle is configured with Heating or Manual Air
Conditioning (SC008 UCH type and CF019 Type of air conditioning).
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
ET028 Released with press on the button.
ET028 Pressed without press on the button.
Check the condition and connection of the air conditioning control panel connector (bent, broken tabs, etc.).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the UCH connector PE2 (tabs bent, broken).
If the connector is faulty and if there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 15M between components 645 and 139.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the control panel (see 62C, Manual air conditioning).
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET028/UCH_V48_ET028/ UCH_V4C_ET028/
UCH_V4D_ET028 /UCH_V4F_ET028/UCH_V50_ET028

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -157
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -157V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
*RCH = Passenger Compartment Heating ResistorET031
FAST IDLE SPEED REQUEST FOR RCH
NOTESThere must be no present or stored faults.
ET031 Inactive with engine at idling speed with the passenger compartment heating resistors switched on.
In case of inconsistency, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET031/UCH_V48_ET031/ UCH_V4C_ET031/
UCH_V4D_ET031 /UCH_V4F_ET031/UCH_V50_ET031

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Command summary table87B
87B - 246
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Command summary table87B
87B - 246V9 MR-372-J84-87B000$731.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Command summary table
*RCH: Passenger Compartment Heating Resistor
*CPE: Electric central door locking
*SR.: SunroofTool command Diagnostic tool title Vdiag
AC003Immobiliser warning light
V44, V48,
V4C, V4D,
V4F, V50 AC004Central door locking
AC005Central door unlocking
AC006Driver's door unlocking
AC007Rear screen wiper
AC008Front fog lights
AC009Rear fog lights
AC015Air conditioning button indicator light
AC016RCH* 1 relay
AC017RCH* 2 relay
AC018RCH* 3 relay
AC019Heated rear screen indicator light
AC020CPE* button indicator light
AC021Interior lights
AC022Left-hand direction indicator
AC023Right-hand direction indicator
AC024Card reader lighting
AC025One-touch window control/SR.* authorisation
AC026Start button lighting
AC027Footwell lights
AC030Headlight washer relay 1 (only if Vdiag 44 UPC)
AC031Headlight washer relay 2 (only if Vdiag 44 UPC)
AC032Driver's side external aerial testing
AC033Passenger's side external aerial testing
AC034Boot external aerial test
AC036Internal aerial test
AC037Transmitter aerial fault finding
AC076Child safety lock indicator light
MR-372-J84-87B000$731.mif