wiring diagram RENAULT SCENIC 2008 J84 / 2.G Passenger Comparment Connection Unit Manual PDF

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 248
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 248V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
AC003
IMMOBILISER INDICATOR LIGHT
NOTESNo faults should be present or stored.
The instrument panel must be detected as present on the multiplex network.
This command is for testing whether the immobiliser warning light is working.
The command lasts 10 seconds.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
The immobiliser indicator light does not come on when the command is performed.
Check the condition and connection of the instrument panel connector.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
With the command running, check for earth on connection 88T of component 427.
If okay, replace the instrument panel.
Check the condition and connection of connector PE2 on the UCH
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 20W between components 645 and 427.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
MR-372-J84-87B000$774.mif

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 249
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 249V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC004
LOCK DOORS AND BOOT
NOTESNo faults should be present or stored.
This command is for testing locking relay operation.
Note:
The driver's door circuit is shared with the fuel tank flap circuit.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
One or more doors do not lock when the command is activated.
Check the condition and connection of the PP2 connector on the UCH.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the connector on the faulty lock(s).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on the following connections:
●Connection code MAM.
●Connection code 87H of component 140.
●Connection code MZ.
●Connection code 87A of component 139.
●Connection code MAN.
●Connection code 87G of component 141.
●Connection code MAQ.
●Connection code 87B of component 138.
●Connection code 20BC.
●Connection code 20BH of component 844.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If faulty: If OK:
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 251
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 251V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC005
AC006
UNLOCK DOORS AND BOOT
DRIVER'S DOOR UNLOCKING
NOTESNo faults should be present or stored.
This command is for testing unlocking relay operation.
The driver's door circuit is shared with the fuel tank flap circuit.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
One or more doors do not unlock when the commands are activated.
Check the condition and connection of the PP2 connector on the UCH.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the connector on the faulty lock(s).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on:
●Connection code MAM.
●Connection code 87H.
Of component 140.
●Connection code MZ.
●Connection code 87A.
Of component 139.
●Connection code MAN.
●Connection code 87G.
Of component 141.
●Connection code MAQ.
●Connection code 87B.
Of component 138.
●Connection code 20BC.
●Connection code 20BH.
Of component 140.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If faulty: If OK:
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 253
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 253V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC007
REAR SCREEN WIPER
NOTESNo faults should be present or stored.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
The rear screen wiper does not operate when the command is activated.
Check the condition and connection of the rear screen wiper motor connector.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on connection MZ of component 211.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
With the command running, check for + 12 V feed on connection 36A of component 211.
If everything is correct, replace the rear screen wiper motor.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of connector PE3 on the UCH.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connections:
●Connection code 36A.
●Connection code 36C between components 645 and 211.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 254
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 254V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC008
FRONT FOG LIGHTS
NOTESCheck:
–the condition and connection of the front fog lights fuse,
–the condition of the bulbs.
Replace the bulbs if necessary.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
The rear screen wiper does not operate when the command is activated.
Check the condition and connection of connector PPA on the UPC (Vdiag 44) or connector AN on the UPC
(Vdiag 48 or above).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the condition and connection of the bulb connectors.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on R9 connection then check the connections of the bulb connectors.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for + 12 V on the fog light connectors they are being controlled by command AC004.
If the + 12 V on the connectors is correct, replace the bulb(s).
Check the insulation and continuity of the following connections:
●Connection code 8F between components 176 and 1337.
●Connection code 8E between components 177 and 1337.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 255
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 255V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC009
REAR FOG LIGHTS
NOTESNo faults should be present or stored.
This command is for testing operation of the rear fog lights.
Check the bulbs.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Left-hand drive
Check the condition and connection of the connector for each rear light.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on connection MZ on component 173.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
With the command running, check for + 12 V feed on connection 9P of component 173.
If the + 12 V feed is correct, check the bulbs again and if the bulbs still do not work, replace the rear light.
Check the condition and connection of UCH connector PP3.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 9P between components 645 and 173.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 257
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 257V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC015
AIR-CONDITIONING BUTTON INDICATOR LIGHT
Manual air conditioning only
NOTESNo faults should be present or stored.
This command is for testing operation of the air-conditioning indicator light.
Apply the after ignition feed, and the air conditioning control panel should light up.
The command lasts 7 seconds.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
The indicator light does not light up when the command is activated.
Check the condition and connection of the heater control panel connector.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on connection NAM of component 316.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
With the command running, check for + 12 V feed on connection 38ES of component 316.
If OK, replace the control panel.
Check the condition and connection of connector PE2 on the UCH
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 38ES between components 645 and 319.
●Connection code NAM between component 319 and earth.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 258
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 258V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
*RCH: Passenger Compartment Heating ResistorsAC016
RCH* 1 RELAY
NOTESCheck that the vehicle is fitted with passenger compartment heating resistors.
No faults should be present or stored.
This command is for testing the operation of the passenger compartment heating
resistors.
The command lasts 7 seconds.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check for earth on connection NAM of
component 1113.
If the connector is faulty and if there is a repair
procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair),
repair the connector; otherwise, replace the wiring.
With the command running, check for + 12 V feed on
connection 38LL of component 1113.
NO
Check for + 12 V on connection BP9 of
component 1067.
NO
YESCheck that the resistances, between
connections 38LL and MAK (track 2) and
between connections 38LL and MAK
(track 4) of component 1113, are equal to
infinity. Replace the passenger
compartment heating resistors if faulty.
YESCheck the insulation and continuity of
the following connection:
●Connection code 38LL between
components 1067 and 1113.
If the connector is faulty and if there is a
repair procedure (see Technical Note
6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair
the connector; otherwise, replace the
wiring.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 261
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 261V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
*RCH: Passenger Compartment Heating ResistorsAC017
RCH* 2 RELAY
NOTESCheck that the vehicle is fitted with passenger compartment heating resistors.
No faults should be present or stored.
This command is for testing the operation of the passenger compartment heating
resistors.
The command lasts 7 seconds.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check for earth on connections MAK of
component 1113.
If the connector is faulty and if there is a repair
procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair),
repair the connector; otherwise, replace the wiring.
With the command running, check for + 12 V feed on
connection 38LM of component 1113.
NO
Check for + 12 V on connection 38LM of
component 1068.
NO
YESCheck that the resistances, between
connections 38LM (track 1) and MAK
(track 2) and between connections 38LM
(track 5) and MAK (track 4) of
component 1113, are equal to infinity.
Replace the passenger compartment
heating resistors if faulty.
YESCheck the insulation and continuity of
the following connection:
●Connection code 38LM between
components 1068 and 1113.
If the connection is faulty and there is a
repair procedure (see Technical Note
6015A, Electrical wiring repair, Wiring:
Precautions for repair), repair the wiring,
otherwise replace it.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 264
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87B
87B - 264V9 MR-372-J84-87B000$774.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
AC019
HEATED REAR SCREEN INDICATOR LIGHT
Except with climate control
NOTESNo faults should be present or stored.
This command is for testing operation of the heated rear screen indicator light.
Apply after ignition feed.
The command lasts 7 seconds.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
The heated rear screen indicator light does not light up when the command is activated.
Check the condition and connection of the heater control panel connector.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check for earth on connection NAM of component 319.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
With the command running, check for + 12 V feed on connection 15A of component 316.
If OK, replace the control panel.
Check the condition and connection of connector PE2 on the UCH
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector; otherwise, replace the wiring.
Check the insulation and continuity of the following connection:
●Connection code 15A between components 645 and 319.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.