air condition RENAULT SCENIC 2010 J95 / 3.G Engine Compartment Connection Unit User Guide

87G - 38
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
87G
V6 MR-372-J84-87G000$792_eng.mif
UPC
Vdiag No.: 44
Without xenon lights AC002
DIPPED BEAM HEADLIGHTS
NOTESCheck:
–the status and the connection of fuses 8C and 8D on the UPC,
–the status of the bulbs.
Replace them, if necessary.
Check the status and connection of connector PPA and the fuses on the UPC.
Repair if necessary.
Check the condition and connection of the headlight connectors.
Repair if necessary.
Check the presence of earth on connection R9 then on track 1 of the headlight connector.
Repair if necessary.
Check the presence of +12 V on track 2 of the headlights when controlled by command AC002.
If everything is find, replace the bulb or bulbs.
If there is a fault, check the insulation against earth and the continuity of the connections:
UPC connector PPA track 6 Left headlight track 2
UPC connector PPA track 5 Right headlight track 2
Repair if necessary.
If the fault is still present, contact the Techline.

87G - 39
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
87G
V6 MR-372-J84-87G000$792_eng.mif
UPC
Vdiag No.: 44
With xenon lights AC002
(continued)
Check the status and the connection for connector PPA and the fuses on the UPC.
Repair if necessary.
Check the condition and connection of the headlight connectors.
Repair if necessary.
Check for the presence of earth on connection R9 then on tracks 4 and 10 of the headlight connectors.
Repair if necessary.
Check that there is a +12 V supply on track 3 of the headlights when controlled by command AC002.
If everything is fine, apply the fault finding procedure (see 80C, Discharge bulbs).
If there is a fault, check the insulation against earth is in place and continuity on the connections:
UPC connector PPA track 6 Left headlight track 3
UPC connector PPA track 5 Right headlight track 3
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.

87G - 40
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
87G
V6 MR-372-J84-87G000$792_eng.mif
UPC
Vdiag No.: 44
Without xenon lights AC003
SIDE LIGHTS
NOTESCheck:
–the status and connection of fuses 7A and 7B on the UPC,
–the status of the bulbs.
Replace them, if necessary.
Check the condition and connection of connectors PPA and PPH2 and the fuses in the Protection and
Switching Unit.
Repair if necessary.
Check the condition and connection of the headlights and rear lights.
Repair if necessary.
Check for the presence of earth on connection R9 then on track 1 of the headlights and on track 2 of the rear
lights and the vehicle number plate lights.
Repair if necessary.
Check that there is a +12 V supply on track 5 of the headlights and track 1 of the rear lights and the number
plate when controlled by command AC003.
If everything is fine, replace the bulb or bulbs.
If there is a fault, check the insulation against earth and continuity of the connections:
UPC connector PPH2 track 6 Left rear light track 1
UPC connector PPH2 track 7 Track 1 right-hand rear light and number plate lights
UPC connector PPA track 1 Left headlight track 5
UPC connector PPA track 2 Right headlight track 5
Repair if necessary.
If the fault is still present, contact the Techline.

87G - 41
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
87G
V6 MR-372-J84-87G000$792_eng.mif
UPC
Vdiag No.: 44
With xenon lights AC003
(continued)
Check the status and connection of connectors PPA and PPH2 and the fuses on the UPC.
Repair if necessary.
Check the condition and connection of the headlights and rear lights.
Repair if necessary.
Check for the presence of earth on connection R9 then on tracks 4 and 10 of the headlights and on track 2
of the rear lights and the number plate lights.
Repair if necessary.
Check for the presence of +12 V supply on track 9 of the headlights and track 1 of the rear lights and the
number plate lights when controlled by command AC003.
If everything is fine, replace the bulb or bulbs.
If there is a problem, check the insulation against earth and continuity of the connections:
UPC connector PPH2 track 6 Left rear light track 1
UPC connector PPH2 track 7 Track 1 right-hand rear light and number plate lights
UPC connector PPA track 1 Left headlight track 9
UPC connector PPA track 2 Right headlight track 9
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.

87G - 42
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
87G
V6 MR-372-J84-87G000$792_eng.mif
UPC
Vdiag No.: 44
AC004
FRONT FOG LIGHTS
NOTESCheck:
–the condition and the connection of fuse 10,
–the condition of the bulbs.
Replace them, if necessary.
Check the condition and connection of connector PPA on the UPC.
Repair if necessary.
Check the condition and connection of the bulb connectors.
Repair if necessary.
Check the presence of earth on connection R9 and then on the bulb connectors.
Repair if necessary.
Check the presence of +12 V on the fog light connectors while controlled by command AC004.
If everything is correct, replace the bulb or bulbs.
Check the continuity and insulation of the following connections:
UPC connector PPA track 8 Track 1 of the left-hand front fog light connector
UPC connector PPA track 7 Track 1 of the right-hand front fog light
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.

87G - 43
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
87G
V6 MR-372-J84-87G000$792_eng.mif
UPC
Vdiag No.: 44
AC005
LOW-SPEED WINDSCREEN WIPER
NOTESCheck:
–the condition and connection of fuse 9.
Replace it if necessary.
Check the condition and connection of connector PPH2 on the UPC.
Repair if necessary.
Check the condition and connection of the front windscreen wiper motor.
Repair if necessary.
Check for the presence of earth on track 1 of the windscreen wiper motor.
Repair if necessary.
Check for the presence of a +12 V supply on track 4 of the windscreen wiper motor while controlled by
command AC005.
If correct, replace the motor.
Check the insulation and continuity of the connection between:
UPC connector PPH2 track 2 Track 4 of the windscreen wiper motor
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.

87G - 44
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
87G
V6 MR-372-J84-87G000$792_eng.mif
UPC
Vdiag No.: 44
AC006
HIGH-SPEED WINDSCREEN WIPER
NOTESCheck:
–the condition and connection of fuse 9
Replace it if necessary.
Check the condition and connection of connector PPH2 on the UPC.
Repair if necessary.
Check the condition and connection of the windscreen wiper motor.
Repair if necessary.
Check for the presence of earth on track 1 of the windscreen wiper motor.
Repair if necessary.
Check for the presence of a +12 V supply on track 5 of the windscreen wiper motor while controlled by AC006.
If correct, replace the motor.
Check the insulation and continuity of the connection between:
UPC connector PPH2 track 1 Track 5 of the windscreen wiper motor
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.

87G - 45
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
87G
V6 MR-372-J84-87G000$792_eng.mif
UPC
Vdiag No.: 44
AC008
COMPRESSOR CONTROL
NOTESThis command is not permitted when the engine is running.
Check:
–the condition and the connection of fuse 4.
Replace it if necessary.
Check the condition and connection of connector PPM2 on the UPC.
Repair if necessary.
Check the cindition and connection of the air conditioning compressor.
Repair if necessary.
Make sure that the compressor is properly earthed.
Check for the presence of a +12 V supply on the compressor connector while controlled by command AC008.
If there is a fault, check the insulation against earth and continuity of the connection:
UPC connector PPM2 track 5 Air conditioning compressor connector
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.

87G - 46
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
87G
V6 MR-372-J84-87G000$792_eng.mif
UPC
Vdiag No.: 44
AC009
LOW-SPEED FAN UNIT
NOTESCheck:
–the condition and connection of fuse 11.
Replace it if necessary.
The fans must have stopped.
Make sure nothing is mechanically blocking the blade rotation.
Check the condition and connection of the fan connector.
Repair if necessary.
Ensure that there is a good earth connection on track 2 of the fan.
Check that the resistor in the fan unit (if it exists) is not in open circuit with a resistance equal to 0.69 ΩΩ Ω Ω
± 20%.
If not correct, replace it.
Check that there is a +12 V supply on the fan while controlled by command AC009.
If everything is correct, replace the fan.
If there is a problem, check the insulation against earth and continuity of the connections:
UPC connector PPM1 track 4 Track 1 of the fan
OR
UPC connector PPM1 track 4 Resistor in the fan unit (if it exists)
Resistance in the fan unit (if it exists) Track 1 of the fan
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.

87G - 47
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
87G
V6 MR-372-J84-87G000$792_eng.mif
UPC
Vdiag No.: 44
UPC type N2 AC010
HIGH-SPEED FAN UNIT
NOTESThis command is only applicable on versions fitted with air conditioning.
Check:
–the condition and connection of fuse 11 (UPC level N3 only).
Replace it if necessary.
Check the condition and connection of the fan connector.
Repair if necessary.
Ensure that the fan is properly earthed.
Check the resistance of the external high-speed fan control relay: 65 ΩΩ Ω Ω
± 10 ΩΩ Ω Ω
.
Replace it if necessary.
Check the presence of +12 V on track 1 of the high-speed fan external control relay when controlled by
command AC010.
If there is a fault, check the insulation against earth and continuity of the connection
UPC connector PPM2 track 3 Track 1 of the high-speed fan external control relay
Repair if necessary.
Check that there is earthing on track 2 of the high-speed fan external control relay.
If there is a fault, check the insulation against +12 V and continuity of the connection:
UPC connector PPM2 track 2 Track 2 of the high-speed fan external control relay
Repair if necessary.
Check for the presence of +12 V supply on track 1 of the fan while controlled by command AC010.
If there is a problem, check the insulation against earth and continuity of the connection:
Fan track 1 Track 5 of the high-speed fan external control relay
Repair if necessary.