fuse box RENAULT SCENIC 2010 J95 / 3.G Engine Compartment Connection Unit Workshop Manual

87G - 30
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87G
V6 MR-372-J84-87G000$660_eng.mif
UPC
Vdiag No.: 44
Manual gearbox ET004
REVERSE GEAR ENGAGED
NOTESCheck, and if necessary, replace fuse 5C on the UPC.
Check the status and the connection of the reverse gear switch connector and connector PPM2 on the UPC.
Repair if necessary.
With the ignition on and reverse gear selected, check the presence of +12 V on track 9 of connector PPM2.
If there is a fault, check the insulation against earth and continuity of the connections:
UPC connector PPM2 track 9 Track 1 (track 3 on the ND0 gearbox) of the switch
UPC connector PPM2 track 6 Track 2 (track 1 on gearbox ND0) of the switch
Repair if necessary.
With reverse gear selected, check the continuity between tracks 1 and 2 (or tracks 1 and 3 on gearbox NDO)
of the switch.
Replace the reverse gear switch if necessary.
If the fault is still present, contact the Techline.

87G - 32
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87G
V6 MR-372-J84-87G000$660_eng.mif
UPC
Vdiag No.: 44
ET005
POSITION OF GEAR LEVER IN MANUAL GEARBOX
NOTESCheck, and if necessary, replace fuse "5C" on the UPC.
Applicable on vehicles fitted with a manual gearbox only.
Check the status and the connection of the neutral switch connector and connectors PPM2 and PEM on the
UPC.
Repair if necessary.
With the ignition on and in neutral, check the presence of +12 V on track 6 of connector PEM. If there is a fault,
check the insulation against earth and the continuity of the connection between the switch and track 6 of
connector PEM on the UPC.
Check the operation of the switch:
There is continuity between tracks 1 and 2 of the switch when the gearbox is in neutral.
There is an open circuit between tracks 1 and 2 of the switch when a gear is selected.
If faulty, replace the switch.
With the ignition on, check the presence of +12 V on track 2 (track 1 on gearbox ND0) of the neutral switch
connector.
If there is a fault, check the insulation against earth and the continuity of the connection between the switch
and track 6 of connector PPM2 on the UPC.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.

87G - 51
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
87G
V6 MR-372-J84-87G000$792_eng.mif
UPC
Vdiag No.: 44
Rear-view mirrors (if equipped with heaters) AC011
(continued)
Check the condition and connection of connector PPH1 on the UPC.
Repair if necessary.
Check the condition and connection of the rear-view mirror connectors.
Repair if necessary.
Check for the presence of earth on track 5 of the rear view mirror connectors.
Check for the presence of a +12 V supply on track 1 of the rear view mirror connector while controlled by
command.
If there is a fault, check the insulation against earth and continuity of the connection:
UPC connector PPH1 track 2 Track 1 of the rear view mirror passing via the fuse box and
the passenger compartment relay
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.