engine RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Injection User Guide

13B - 15
DIESEL INJECTION
Fault finding - System operation13B
V10 MR-372-J84-13B150$094.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
d) OBD management
The OBD (On Board Diagnostic) system enables detection of any faults relating to the vehicle emission control
system (OBD EURO IV emission control standards exceeded).
This system should be active for the entire life of the vehicle.
1. Conditions causing an OBD fault
An OBD fault will be detected after 3 operating cycles, and the following parameters will be saved in the calculator:
– engine load,
– vehicle speed,
– air temperature,
– coolant temperature,
– turbocharging pressure,
– rail pressure,
–air flow,
– vehicle mileage.
It allows the driver to know whether their vehicle has a fault directly linked to the emission control system.
2. System faults indicated by the OBD
Only a few faults are indicated by the OBD system:
–DF012 Sensor supply voltage no. 2.
–DF038 Computer.
–DF040 Cylinder 1 injector circuit.
–DF041 Cylinder 2 injector circuit.
–DF042 Cylinder 3 injector circuit.
–DF043 Cylinder 4 injector circuit.
–DF209 EGR valve position sensor circuit.
–DF272 EGR valve control circuit.
–DF621 EGR valve jammed open.
Some repair operations require programming to ensure that certain engine components function correctly.
Follow the programming procedures (described in the component replacement section), if replacing an
exhaust gas recirculation valve or an injector.

13B - 16
DIESEL INJECTION
Fault finding - System operation13B
V10 MR-372-J84-13B150$094.mif
EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C
3. Conditions for clearing an OBD fault
An OBD fault is cleared in several steps.
The fault present in the diagnostic tool is not stored (following repair) until after 3 trips with the vehicle.
The OBD warning light will only light up after these 3 driving cycles.
The warning light coming on does not always mean that there is a fault on the system.
In order that the OBD fault and the display parameters are cleared from the computer, the system goes
through 40 engine heating cycles.
An engine heating cycle is a driving cycle during which:
–the engine coolant temperature reaches at least 71.1 °C,
–the engine coolant temperature varies by 22.2 °C in relation to the engine starting temperature.
If one of these conditions is not fulfilled, the OBD fault will still be present or stored in the injection
computer.

13B - 20
DIESEL INJECTION
Fault finding - Replacement of components13B
V10 MR-372-J84-13B150$188.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4CDIESEL INJECTION
Fault finding - Replacement of components
COMPUTER REPLACEMENT OR REPROGRAMMING OPERATIONS
The system can be programmed or reprogrammed via the diagnostic socket using the RENAULT CLIP diagnostic
tool (see Technical Note 3585A).
While the computer is being reprogrammed the engine fan assemblies are automatically triggered).
Operations to be carried out before reprogramming the injection computer:
Before reprogramming the injection computer, move the main Cruise control/Speed limiter switch to the rest position.
The information about the cruise control or the speed limiter displayed on the instrument panel disappears.
Otherwise, if the main switch remains in the cruise control or speed limiter position during and after reprogramming,
the Cruise control/Speed limiter function will not be operational.
To reset the function, proceed as follows:
Vehicle ignition on.
– Position the main switch in rest position (the computer then detects the rest position).
– Position the switch in Cruise control position to activate the Cruise control function.
– Position the switch in Speed limiter position to activate the Speed Limiter function.
Before reprogramming or replacing the computer in After-Sales operations, backup the following data to the
diagnostic tool:
– The IMA codes (individual correction of the injector).
– The engine adaptives (engine speed, and options available on the vehicle).
(this file corresponds to the last save carried out on the tool)
select YES,
When the backup is complete, replace the computer or reprogram, then proceed to the next step,
with command SC003 Backup computer data. IMPORTANT
–Switch on the diagnostic tool (mains or cigarette lighter feed).
–Connect a battery charger.
–Switch off all electrical consumers (lights, interior lights, air conditioning, radio/CD, etc.).
–Wait for the engine to cool (engine coolant temperature below 60 °C and air temperature below 50 °C).
WARNING
A computer without the IMA option can be replaced by a computer with this option. The codes have
therefore not been backed up during command SC003.
In this case, status ET104 "Injector code use" becomes "YES" or "FAULTY", fault DF276 "Injector code
programming" is present, and the engine operates in defect mode.
In this case, run command SC002 Enter injector codes, applying the procedure described in the
interpretation of this command.
MR-372-J84-13B150$188.mif

13B - 21
DIESEL INJECTION
Fault finding - Replacement of components13B
V10 MR-372-J84-13B150$188.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
After programming, reprogramming or replacing the computer:
–switch the ignition off and then on again,
–start and then stop the engine (to initialise the computer) and wait for 30 seconds,
–use the diagnostic tool to carry out the following procedures:
– run command SC001 Enter saved data, to re-establish the injector codes and engine adaptives,
– run command VP010 Enter VIN,
– deal with any faults declared by the diagnostic tool. Clear the computer memory.
– carry out a road test followed by another check with the diagnostic tool.
Note:
If commands SC001 and SC003, have been forgotten or do not work after replacing or (re)programming the
computer, enter the IMA codes for each injector manually by reading the code on each injector (see Replacement
of injectors).
IMPORTANT
– the injection computer retains the immobiliser code for life,
– the system has no security code,
– it is prohibited to perform tests with computers borrowed from the Parts Department or from another vehicle
which must then be returned,
– these computers are hard-coded,
– if the injection computer appears to be faulty, contact the Techline and refer to the fault finding log.

13B - 22
DIESEL INJECTION
Fault finding - Replacement of components13B
V10 MR-372-J84-13B150$188.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
REPLACING THE INJECTORS
When one or more injectors are replaced, the IMA parameters of the injector output concerned must be modified.
The system can be configured with the diagnostic socket using the RENAULT CLIP diagnostic tool.
To do this, display the IMA code(s) etched on the injector bodies, and enter the codes into the computer using
command SC002 Enter injector codes, and follow the instructions given by the diagnostic tool.
REPLACING THE EXHAUST GAS RECIRCULATION VALVE
When replacing the exhaust gas recirculation valve, enter the operational values of the new valve into the computer.
After replacing the exhaust gas recirculation valve, select Clear mode on the diagnostic tool.
Run command RZ002 EGR adaptives.
When the command is completed, switch off the ignition and exit fault finding mode.
–wait 30 seconds, and switch on the ignition again,
– clear any faults,
– start the engine,
– let the engine idle for 1 min, accelerate to 2500 rpm for 5 s, and return to idle speed,
– repeat this procedure 5 times.
Check the faults:
If the fault does not recur, end of fault finding procedure.
If the fault recurs, restart the procedure after disconnecting and reconnecting the valve.
If the fault is still present, replace the EGR valve. Note:
The IMA coding (individual injector correction) is a calibration made in production on each injector to adjust
the flow accurately.
These correction values are etched on the Bakelite body of each injector (6 alphanumeric characters) and then
entered into the computer which then controls each injector taking into account their manufacturing variation.
IMPORTANT
When the command is complete, switch off the ignition and exit fault finding mode.
Wait 30 seconds.
Return to fault finding mode.
Select the Identify computer function from the main screen.
Check that the injector codes entered into the computer correspond to those on the injector bodies.
If the codes do not match, restart the command SC002 Enter injector codes procedure.
Then check the system faults, and clear any stored faults.
If the computer does not have any faults, the operation is complete.
If there are faults, deal with the present faults.

13B - 23
DIESEL INJECTION
Fault finding - Fault summary table13B
V10 MR-372-J84-13B150$235.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4CDIESEL INJECTION
Fault finding - Fault summary table
WARNING LIGHT MANAGEMENT
Management of instrument panel warning lights according to the faults notified.
Tool
fault
Associated
DTCDiagnostic tool titleLevel 1 fault
warning light
(Orange heater
plugs “on”
indicator light)Level 2 fault
warning light (Red
overheating
warning light)No fault
warning
light litOBD
warning
light lit
DF001 115Coolant temperature sensor
circuitCO.1/CC.0 ... ... ...
DF003 105Atmospheric pressure sensor
circuit1.DEF / 2.DEF /
3.DEF... ... ...
DF004 235Turbocharging pressure sensor
circuitCO.0 / CC.1 ... 1.DEF ...
DF005 335Engine speed sensor circuit ... ... 1.DEF/2.DEF ...
DF007 190Rail pressure sensor circuit CO.1 / 1.DEF /
2.DEFCC.0 ...
DF008 225Pedal potentiometer circuit
gang 1CO.0/CC.1/
1.DEF/2.DEF... ... ...
DF009 2120Pedal potentiometer circuit
gang 2CO.0/CC.1/
1.DEF... ... ...
DF011 641Sensor feed voltage no. 1 1.DEF/2.DEF ... ... ...
DF012 651Sensor feed voltage no. 2 1.DEF/2.DEF ... ... 1.DEF/
2.DEF
DF013 697Sensor feed voltage no. 3 ... 1.DEF/2.DEF ... ...
DF015 685Main relay control circuit ... ... 1.DEF/2.DEF ...
DF017 380Pre-postheating unit control
circuitCC.0 ... CC.1/CO/
1.DEF...
DF025 670Preheating unit diagnostic line ... X ...
DF037 C167Engine immobiliser ... X ...
DF038 606Computer 5.DEF / 13.DEF 1.DEF / 2.DEF /
3.DEF / 4.DEF /
6.DEF / 7.DEF /
8.DEF / 9.DEF /
10.DEF / 11.DEF /
12.DEF... 5.DEF
DF039 110Inlet air temperature sensor
circuit... ... CC.0/CO.1/
1.DEF...
MR-372-J84-13B150$235.mif

13B - 25
DIESEL INJECTION
Fault finding - Fault summary table13B
V10 MR-372-J84-13B150$235.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
FAULT WARNING LIGHT MANAGEMENT (continued)
Tool
fault
Associated
DTCDiagnostic tool titleLevel 1
fault warning
light (Orange
heater plugs
“on” indicator
light)Level 2 fault
warning light
(Red overheating
warning light)No fault
warning
light litOBD
warning
light lit
DF091 500Vehicle speed signal ... ... 1.DEF/
2.DEF/
3.DEF/
4.DEF/5.DEF...
DF097 340Camshaft sensor circuit 1.DEF/2.DEF
DF098 180Fuel temperature sensor circuit ... ... CC.0 / CO.1
DF114 400EGR solenoid valve circuit ... ... 1.DEF/2.DEF
DF118 409EGR solenoid valve servo-
control... ... 1.DEF/2.DEF ...
DF119 365Camshaft sensor signal ... ... 1.DEF/2.DEF ...
DF120 385Engine speed sensor signal ... 1.DEF/2.DEF ...
DF209 486EGR valve position sensor circuit 1.DEF CC.1/CO.0
DF250 C122ESP function ... ... 1.DEF/2.DEF ...
DF272 403EGR valve control circuit CC.0 CC.1 / CO/
1.DEFCC.0
DF276 611Injector code programming 1.DEF/2.DEF
DF530 148AEGR programming adaptives X
DF619 487EGR valve jammed open X ... ... ...
DF620 148BEGR valve fouled X ... ... ...
DF621 2413EGR valve is jammed open
(OBD fault)... ... ... X
DF622 2142EGR valve jammed open ... ... X ...
DF1070 534Cold loop

13B-26
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4CDIESEL INJECTION
Fault finding - Interpretation of faults
DF001
PRESENT
OR
STOREDCOOLANT TEMPERATURE SENSOR CIRCUIT
CC.0 : short circuit to earth
CO.1 : open circuit or short circuit to + 12 V
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present with the engine running or following a road test.
Special notes:
If the fault is present:
– the coolant temperature: PR064: Coolant temperature is fixed at 119°C,
– the preheating phase is greater than 10 seconds,
– the fan assembly is permanently supplied,
The level 1 warning light comes on.
Use bornier Elé. 1681 for any work on the computer connectors.
CC.0
NOTESNone.
Check the coolant temperature sensor connections.
Repair if necessary.
Measure the resistance of the coolant temperature sensor between terminals 2 and 3 of its black connector.
Replace the sensor if its resistance is not approximately: 12460±112Ω at -10°C
2252±112Ω at 25°C
811.4±39Ω at 50°C
283±8Ω at 80°C
115±3Ω at 110°C
Check the injection computer connections.
Check for continuity and the absence of interference resistance of the following connections:
Injection computer brown 48-track connector B, track F2 Track 3 coolant temperature sensor
Injection computer brown 48-track connector B, track H1 Track 2 coolant temperature sensor
Repair if necessary.
If the fault is still present, replace the coolant temperature sensor.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF001/EDC16_V48_DF001/EDC16_V4C_DF001
MR-372-J84-13B150$282.mif

13B-28
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF003
PRESENT
OR
STOREDATMOSPHERIC PRESSURE SENSOR CIRCUIT
1.DEF : Signal outside upper limit
2.DEF : signal outside lower limit
3.DEF : inconsistent signal
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present after:
–the engine is started,
–a road test.
Special notes:
The atmospheric pressure sensor is integrated into the injection computer and cannot
be separated.
If the fault is present:
– there is light smoke,
– the atmospheric pressure value changes to default mode, PR035 Atmospheric
pressure = 750 mbar,
–the level 1 warning light is lit.
Use bornier Elé. 1681 for any work on the computer connectors.
Disconnect the injection computer and check the condition of the contacts and connector.
Repair if necessary.
Display the value of parameter PR041 Turbocharging pressure.
If this value is stuck at 750 mbar, refer to interpretation of fault DF004 Turbocharging pressure sensor
circuit.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF003/EDC16_V48_DF003/EDC16_V4C_DF003

13B-29
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF004
PRESENT
OR
STOREDTURBOCHARGING PRESSURE SENSOR CIRCUIT
CO.0 : open circuit or short circuit to earth
CC.1 : short circuit to + 12 V
1.DEF : signal incoherence
NOTESOrder of priority in the event of more than one fault:
In the event of a combination of faults DF004 and DF011 Sensor supply voltage
no.1, deal with fault DF011 first.
Conditions for applying the fault finding procedure to a stored fault:
The fault is declared present after starting the engine, or during a road test.
Special notes:
Use bornier Elé. 1681 for all operations on the injection computer connectors.
If the fault is present:
– the EGR function is inhibited,
– the turbocharging pressure sensor is in defect mode, PR041 = 750 mbar,
– the intake air temperature is in defect mode, PR059 = 25°C.
The level 1 warning light comes on.
CO.0
NOTESNone.
Check the turbocharger pressure sensor connections.
Check the injection computer connections.
Repair if necessary.
Check the continuity and insulation from earth of the following connections:
Injection computer brown 48-track connector B, track K2 Track 3 turbocharger pressure
sensor connector
Injection computer brown 48-track connector B, track G4 Track 1 turbocharger pressure
sensor connector
Repair if necessary.
If the fault is still present, replace the turbocharging pressure sensor.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF004/EDC16_V48_DF004/EDC16_V4C_DF004