injector RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16 Injection User Guide

13B - 24
DIESEL INJECTION
Fault finding - Fault summary table13B
V10 MR-372-J84-13B150$235.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
Tool
faultAssociated
DTCDiagnostic tool titleLevel 1
fault warning
light (Orange
heater plugs
“on” indicator
light)Level 2 fault
warning light
(Red overheating
warning light)No fault
warning
light litOBD
warning
light lit
DF040 201Cylinder 1 injector circuit CO CC.1 / CC / 1.DEF ... CO
DF041 202Cylinder 2 injector circuit CO CC.1 / CC / 1.DEF ... CO
DF042 203Cylinder 3 injector circuit CO CC.1 / CC / 1.DEF ... CO
DF043 204Cylinder 4 injector circuit CO CC.1 / CC / 1.DEF ... CO
DF046 560Battery voltage ... ... 1.DEF/2.DEF ...
DF047 615Computer feed voltage ... ... X ...
DF049 530Refrigerant sensor circuit ... ... CC.1/CO.0 ...
DF050 571Brake switch circuit ... ... 1.DEF/2.DEF ...
DF051 575Cruise control/speed limiter
function... ... 1.DEF /
2.DEF /
3.DEF...
DF053 89Rail pressure regulation function 3.DEF / 8.DEF CC.0 / CC.1 / CO /
1.DEF / 2.DEF /
5.DEF / 6.DEF / 7.DEF4.DEF ...
DF054 33Turbocharging solenoid valve
control circuitCO/CC.0/CC.1/
1.DEF... ... ...
DF055 243Turbocharging pressure
regulation circuit1.DEF/2.DEF ... ... ...
DF056 100Air flow sensor circuit 3.DEF/4.DEF ... CC.0/CC.1/
1.DEF/2.DEF
DF057 2264Water in diesel fuel detector
circuit... ... X ...
DF067 638Damper control circuit ...
CC.0OC / CC.1 /
1.DEF...
DF069 1620Impact detected signal X
DF070 830Clutch switch circuit ... ... 1.DEF/2.DEF ...

13B - 25
DIESEL INJECTION
Fault finding - Fault summary table13B
V10 MR-372-J84-13B150$235.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
FAULT WARNING LIGHT MANAGEMENT (continued)
Tool
fault
Associated
DTCDiagnostic tool titleLevel 1
fault warning
light (Orange
heater plugs
“on” indicator
light)Level 2 fault
warning light
(Red overheating
warning light)No fault
warning
light litOBD
warning
light lit
DF091 500Vehicle speed signal ... ... 1.DEF/
2.DEF/
3.DEF/
4.DEF/5.DEF...
DF097 340Camshaft sensor circuit 1.DEF/2.DEF
DF098 180Fuel temperature sensor circuit ... ... CC.0 / CO.1
DF114 400EGR solenoid valve circuit ... ... 1.DEF/2.DEF
DF118 409EGR solenoid valve servo-
control... ... 1.DEF/2.DEF ...
DF119 365Camshaft sensor signal ... ... 1.DEF/2.DEF ...
DF120 385Engine speed sensor signal ... 1.DEF/2.DEF ...
DF209 486EGR valve position sensor circuit 1.DEF CC.1/CO.0
DF250 C122ESP function ... ... 1.DEF/2.DEF ...
DF272 403EGR valve control circuit CC.0 CC.1 / CO/
1.DEFCC.0
DF276 611Injector code programming 1.DEF/2.DEF
DF530 148AEGR programming adaptives X
DF619 487EGR valve jammed open X ... ... ...
DF620 148BEGR valve fouled X ... ... ...
DF621 2413EGR valve is jammed open
(OBD fault)... ... ... X
DF622 2142EGR valve jammed open ... ... X ...
DF1070 534Cold loop

13B-50
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$282.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF038
PRESENT
OR
STORED
COMPUTER
CO : open circuit
1.DEF : permanent high signal
2.DEF : permanent low signal
3.DEF : configuration absent or incorrect
4.DEF : analogue/digital converter fault
5.DEF : EEPROM fault
6.DEF : activation in Watchdog
7.DEF : signal outside upper limit
8.DEF : signal outside lower limit
9.DEF : disrupted communication
10.DEF : injector control condenser fault
11.DEF : injector control
12.DEF : Initialisation fault
13.DEF : deceleration fault when decelerating
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after several starting attempts, or with the engine running.
Special notes:
The level 1 warning light is lit for a fault that does not require you to stop the vehicle.
The level 2 warning light is lit for a fault which requires the engine to be switched off.
If 5.DEF is still present, the OBD warning light will come on after three consecutive
driving cycles (starting + 5 seconds + switch off the ignition and wait 40 seconds).
Use bornier Elé. 1681 for all operations on the injection computer connectors.
CO
1.DEF
to
9.DEF
11.DEF
to
13.DEFCheck the injection computer connections and the continuity of all the supplies.
Repair if necessary.
Clear the faults.
Switch off the ignition, wait 30 seconds and switch the ignition on again.
If the fault is still present, contact the Techline and fill out the fault finding log included
in this Technical Note.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF038/EDC16_V48_DF038/EDC16_V4C_DF038

13B-55
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4CDIESEL INJECTION
Fault finding - Interpretation of faults
DF040
PRESENT
OR
STOREDCYLINDER 1 INJECTOR CIRCUIT
CC.1 : short circuit to + 12 V
CO : open circuit
CC : short circuit
1.DEF : Injector control
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine has been started.
Special notes:
If CC.1, CC, or 1.DEF is present, the level 2 warning light is lit.
If CO is present the level 1 warning light is lit.
If CO is still present, the OBD warning light will come on after three consecutive driving
cycles (starting + 5 seconds + switch off the ignition and wait 40 seconds.).
If the fault is present, the injection on cylinder 1 is disabled.
Use bornier Ele. 1681 for all operations on the injection computer connectors.
WARNING
This fault may appear if the wiring harness has been damaged.
Follow the procedure described in the Wiring Check in the Introduction.
This test enables the condition and the conformity of the engine wiring harness to be checked.
CC.1
CO
CC
1.DEF
NOTESNone.
Check the connections on injector no 1.
Check the injection computer connections.
Repair if necessary.
Disconnect injector no. 1.
Measure the resistance of injector no. 1 between tracks 1 and 2.
Replace the injector if there is a short circuit (R = 0Ω) or an open circuit (infinite resistance measurement).
Otherwise, reconnect injector no. 1.
Check the continuity and the absence of interference resistance of the following connections:
Injection computer grey 32-track connector C, track G3 Track 2 injector no. 1
Injection computer grey 32-track connector C, track H1 Track 1 injector no. 1
If the fault is still present: run test 1 INJECTOR TEST.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF040/EDC16_V48_DF040/EDC16_V4C_DF040
MR-372-J84-13B150$329.mif

13B-56
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF041
PRESENT
OR
STOREDCYLINDER 2 INJECTOR CIRCUIT
CC.1 : short circuit to + 12 V
CO : open circuit
CC : short circuit
1.DEF : Injector control
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine has been started.
Special notes:
If CC.1, CC, or 1.DEF is present, the level 2 warning light is lit.
If CO is present the level 1 warning light is lit.
If CO is still present, the OBD warning light will come on after three consecutive driving
cycles (starting + 5 seconds + switch off the ignition and wait 40 seconds.).
If the fault is present, the injection on cylinder 1 is disabled.
Use bornier Ele. 1681 for all operations on the injection computer connectors.
WARNING
This fault may appear if the wiring harness has been damaged.
Follow the procedure described in the Wiring Check in the Introduction.
This test enables the condition and the conformity of the engine wiring harness to be checked.
CC.1
CO
CC
1.DEF
NOTESNone.
Check the connections on injector no. 2.
Check the injection computer connections.
Repair if necessary.
Disconnect injector no. 2.
Measure the resistance of injector no. 2 across tracks 1 and 2.
Replace the injector if there is a short circuit (R = 0Ω) or an open circuit (infinite resistance measurement).
Otherwise, reconnect injector no. 2.
Check the continuity and the absence of interference resistance of the following connections:
Injection computer grey 32-track connector C, track G4 Track 2 injector no. 2
Injection computer grey 32-track connector C, track G2 Track 1 injector no. 2
If the fault is still present: run test 1 INJECTOR TEST.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF041/EDC16_V48_DF041/EDC16_V4C_DF041

13B-57
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF042
PRESENT
OR
STOREDCYLINDER 3 INJECTOR CIRCUIT
CC.1 : short circuit to + 12 V
CO : open circuit
CC : short circuit
1.DEF : Injector control
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine has been started.
Special notes:
If CC.1, CC, or 1.DEF is present, the level 2 warning light is lit.
If CO is present the level 1 warning light is lit.
If CO is still present, the OBD warning light will come on after three consecutive driving
cycles (starting + 5 seconds + switch off the ignition and wait 40 seconds.).
If the fault is present, the injection on cylinder 1 is disabled.
Use bornier Ele. 1681 for all operations on the injection computer connectors.
WARNING
This fault may appear if the wiring harness has been damaged.
Follow the procedure described in the Wiring Check in the Introduction.
This test enables the condition and the conformity of the engine wiring harness to be checked.
CC.1
CO
CC
1.DEF
NOTESNone.
Check the connections on injector no. 3.
Check the injection computer connections.
Repair if necessary.
Disconnect injector no. 3.
Measure the resistance of injector no. 3 between tracks 1 and 2.
Replace the injector if there is a short circuit (R = 0Ω) or an open circuit (infinite resistance measurement).
Otherwise, reconnect injector no. 3.
Check the continuity and the absence of interference resistance of the following connections:
Injection computer grey 32-track connector C, track H4 Track 2 injector no. 3
Injection computer grey 32-track connector C, track H2 Track 1 injector no. 3
If the fault is still present: run test 1 INJECTOR TEST.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF042/EDC16_V48_DF042/EDC16_V4C_DF042

13B-58
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF043
PRESENT
OR
STOREDCYLINDER 4 INJECTOR CIRCUIT
CC.1 : short circuit to + 12 V
CO : open circuit
CC : short circuit
1.DEF : Injector control
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine has been started.
Special notes:
If CC.1, CC, or 1.DEF is present, the level 2 warning light is lit.
If CO is present the level 1 warning light is lit.
If CO is still present, the OBD warning light will come on after three consecutive driving
cycles (starting + 5 seconds + switch off the ignition and wait 40 seconds.).
If the fault is present, the injection on cylinder 1 is disabled.
Use bornier Elé. 1681 for all operations on the injection computer connectors.
WARNING
This fault may appear if the wiring harness has been damaged.
Follow the procedure described in the Wiring Check in the Introduction.
This test enables the condition and the conformity of the engine wiring harness to be checked.
CC.1
CO
CC
1.DEF
NOTESNone.
Check the connections on injector no 4.
Check the injection computer connections.
Repair if necessary.
Disconnect injector no. 4.
Measure the resistance of injector no. 4 between tracks 1 and 2.
Replace the injector if there is a short circuit (R = 0Ω) or an open circuit (infinite resistance measurement).
Otherwise, reconnect injector no. 4.
Check the continuity, and the absence of resistance of the following connections:
Injection computer grey 32-track connector C, track H3 Track 2 injector no. 4
Injection computer grey 32-track connector C, track G1 Track 1 injector no. 4
If the fault is still present: run test 1 INJECTOR TEST.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by a check with the diagnostic tool.
EDC16_V44_DF043/EDC16_V48_DF043/EDC16_V4C_DF043

13B-66
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF053
PRESENT
OR
STORED
RAIL PRESSURE REGULATION FUNCTION
CC.1 : Short circuit to + 12 V
CC.0 : Short circuit to earth
CO : Open circuit
1.DEF : Internal electrical fault
2.DEF : Measured pressure too low
3.DEF : Measured pressure too high
4.DEF : Insufficient pressure
5.DEF : Pressure < minimum
6.DEF : Pressure > maximum
7.DEF : Extensive pump command
8.DEF : significant pump control at idle speed
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present following a road test or after attempting to start the engine.
Special notes:
If the fault is present:
– It is not possible to start the engine.
– the level 2 warning light is lit.
Use bornier Ele. 1681 for all operations on the injection computer connectors.
CC.1
NOTESNone.
Check the rail pressure regulator connectors.
Check the injection computer connections.
Check the low pressure circuit.
Check the conformity of the fuel used, apply test 5 Diesel fuel conformity check.
Check the injector return flow, run test 1 Injector test.
Check the operation of the overpressure valve if fitted to the vehicle, run test 6 Incorrect operation of the
overpressure valve.
Repair if necessary.
Measure the resistance of the rail pressure regulator between tracks 1 and 2.
If the resistance is not 3Ω ±1 at 20°C, replace the injection pump.
Check the continuity and insulation from + 12 V on the following connection:
Injection computer brown 48-track connector B, track M4 Track 2 of the fuel flow actuator
If the fault is still present, replace the injection pump.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.
EDC16_V08_DF053/EDC16_V10_DF053/EDC16_V14_DF053

13B-67
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
DF053
CONTINUED 1
CC.0
CO
NOTESNone.
Check the fuel flow regulator connections.
Check the injection computer connections.
Check the low pressure circuit.
Check the conformity of the fuel used, apply test 5 Diesel fuel conformity check.
Check the injector return flow, run test 1 Injector test.
Check the operation of the overpressure valve if fitted to the vehicle, run test 6 Incorrect operation of the
overpressure valve.
Repair if necessary.
Measure the resistance of the flow regulator between tracks 1 and 2.
If the resistance is not 3Ω ±1 at 20°C, replace the injection pump.
Check the continuity and insulation from earth of the following connection:
Injection computer brown 48-track connector B, track M4 Track 2 of the fuel flow regulator
With the ignition on, check for + 12 V after relay feed on track 1 of the fuel flow regulator.
If the fault is still present, replace the injection pump.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.

13B-68
DIESEL INJECTION
Fault finding - Interpretation of faults13B
V10 MR-372-J84-13B150$329.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
*Opening cyclic ratioDF053
CONTINUED 2
1.DEF
NOTESNone.
Check the rail pressure regulator connectors.
Check the injection computer connections.
Check the low pressure circuit.
Check the conformity of the fuel used, apply test 5 Diesel fuel conformity check.
Check the injector return flow, run test 1 Injector test.
Check the operation of the overpressure valve if fitted to the vehicle, run test 6 Incorrect operation of the
overpressure valve.
Repair if necessary.
Measure the resistance of the flow regulator between tracks 1 and 2.
If the resistance is not 3Ω ±1 at 20°C, replace the injection pump.
Check the continuity and absence of interference resistance of the following connections:
Injection computer brown 48-track connector B, track M4 Track 2 of the fuel flow regulator
UPC, connector PPM1, track 1 Track 1 of the rail pressure
regulator
Repair if necessary.
AFTER REPAIRDeal with any faults.
Carry out a road test followed by another check with the diagnostic tool.