Turbo replacement RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Workshop Manual

13B-146V4 MR-372-J84-13B000$110.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
DDCR INJECTION
Vdiag No.: 44, 48
CLEARING
RZ001: fault memory.
This command is used to clear stored faults from the computer's memory.
RZ002: EGR adaptives.
Run this command only when replacing the EGR valve.
RZ004: Pressure regulation parameters.
Run this command when replacing all 4 injectors at once. It enables you to reset the injector adaptive programs.
RZ005: Programming.
This command lets you reinitialise the entire computer configuration according to the vehicle.
COMMANDS
LPG - FUEL CIRCUIT tab
AC010: High-pressure pump.
This command lets you listen for the operation of the high pressure pump.
AC005 to AC008: Injectors of cylinders 1 to 4.
These commands let you listen for the injector on the selected cylinder.
AC028: Static test.
This command activates fault finding for the EGR and high pressure pump circuits.
AC029: High-pressure circuit seal check.
This command lets you check the high pressure circuit sealing after a procedure has been carried out.
AC212: New pump chamber filling.
Use this command only after replacing the high pressure pump (see High pressure pump replacement in
Replacement of components). This command is used to activate the pump repriming sequence.
IGNITION - PREHEATING tab
AC001: Preheating unit.
This command actuates the preheating unit to test the heater plug supply.
EMISSION CONTROL - OBD tab
AC002: EGR solenoid valve.
This command lets you listen to the mechanical operation of the EGR valve.
AC028: Static test.
This command activates fault finding for the EGR and high pressure pump circuits.
TURBO - INLET AIR CIRCUIT tab
AC004: Turbocharging solenoid valve.
This command lets you listen for the operation of the turbocharging solenoid valve.

13B-160V4 MR-372-J84-13B000$120.mif
DIESEL INJECTION
Fault finding – Tests13B
DDCR INJECTION
Vdiag No.: 44, 48
TEST 11 Turbocharger air chain
Check for the air filter
Check the replacement interval of the air filter on the maintenance booklet.
Compare the part numbers of the air filter fitted to the vehicle and that of the air filter recommended by the
manufacturer.
Check the air filter direction of fitting.
Is the air filter fitted to the vehicle correct?
Check the condition of the air filter
Visually inspect the condition of the filtering section of the air
filter.
Is either the air filter or its seal damaged?
Is the air filter fouled (does it contain a lot of impurities)?Replace the air filter (see MR 364
(Mégane II) or 370 (Scénic II),
Mechanical, 12A, Fuel mixture, Air
filter, Removal - Refitting).
Low pressure circuit check
Note:
Depending on the vehicle type, the best visual access will be
either from above or from below.
Visually inspect the condition of the following components:
– fresh air inlet scoop on the front panel of the vehicle,
– air inlet pipe to the air filter,
– air pipe of the filter until the compressor inlet,
– mountings of the air flowmeter.
Is one of these components incorrect (disconnected,
cut, bent, pierced or kinked pipes)?Replace the defective parts (see MR
364 (Mégane II) or 370 (Scénic II),
Mechanical, 12B, Turbocharging).
YESNO
YES
NO
YES
A
NO
DDCR_V44_TEST11/DDCR_V48_TEST11

13B-191
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V4 MR-372-J84-13B000$140.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
InjectionDDCR
Vdiag No.: 44, 48
ALP16 Engine rattling, noisy engine, turbocharger noise
NOTESOnly consult this customer complaint after a full check with the diagnostic tool.
If the noise arises from the turbocharger, apply Technical Note 5164A, Noise fault finding.
Note:
Pay close attention to faulty components that might result in unjustified replacement of the turbocharger. For
example, whistling does not necessarily indicate damage to the turbocharger (this could be coming from the
exhaust, the timing, the gearbox, etc.).
Check that the fuel tank is correctly filled and that the fuel is correct by running TEST 13 Diesel fuel conformity
check.
Check the levels of engine oil and coolant.
Is the compression in order? Carry out the necessary repairs.
Check the electrical conformity of the heater plugs (the resistance value of the heater plug must be less than 2 Ω).
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes
NO
YES
A
DDCR_V44_ALP16/DDCR_V48_ALP16