suspension RENAULT TWINGO 2009 2.G Chasiss Workshop Manual

Contents
Radiator mounting cross
member: Removal - Refitting 31A-51
Front anti-roll bar: Removal -
Refitting 31A-52
33A REAR AXLE COMPONENTS
Rear brake pads: Removal -
Refitting 33A-1
Rear brake hose: Removal -
Refitting 33A-4
Rear brake calliper: Removal
- Refitting 33A-7
Rear brake calliper
mounting: Removal -
Refitting 33A-9
Rear brake disc: Removal -
Refitting 33A-11
Rear brake disc: Description 33A-13
Rear brake lining: Removal -
Refitting 33A-14
Rear brake cylinder:
Removal - Refitting 33A-17
Rear brake drum: Removal -
Refitting 33A-19
Rear brake drum:
Description 33A-21
Rigid brake pipe: Removal -
Refitting 33A-22
Shock absorber: Removal -
Refitting 33A-24
Rear suspension spring:
Removal - Refitting 33A-28
Rear drum bear ing: Removal
- Refitting 33A-30
Rear stub axle carr ier:
Removal - Refitting 33A-32
Complete rear axle system:
Removal - Refitting 33A-37 31A FRONT AXLE COMPONENTS
35A WHEELS AND TYRES
Wheel: Removal - Refitting 35A-1
Wheel: Balancing 35A-4
Tyres: Identification 35A-7
Tyres: Removal - Refi tting 35A-8
Tyre pressure: Identification 35A-10
Wheel r im: Identifi cation 35A-11
36A STEERING ASSEMBLY
Steering box: Removal -
Refitting 36A-1
Track rod: Removal -
Refitting 36A-2
Axial ball joint linkage:
Removal - Refitting 36A-4
Steering column: List and
location of components 36A-6
Steering column: Removal -
Refitting 36A-7
Steering box gaiter: Removal
- Refitting 36A-16
Bulkhead seal: Removal -
Refitting 36A-17
Intermediate shaft: Removal
- Refitting 36A-18
Steering column adjustment
handle: Removal - Refitting 36A-21
Steering wheel: Removal -
Refitting 36A-23
36B POWER ASSISTED STEERING
Power-assisted steering
computer: Removal -
Refitting 36B-1

31A-20
FRONT AXLE COMPONENTS
Front brake disc: Removal - Refitting
31A
aRemove the brake pads (see 31A, Front axle com-
ponents, Front brake pads: Removal - Refitting,
page 31A-1)
aRemove the "brake calliper mounting - brake calli-
per" assembly (2) (see 31A, Front axle compo-
nents, Front brake calliper mounting: Removal -
Refitting, page 31A-14) .
aHang the "brake calliper mounting - brake calliper"
assembly (2) on the suspension spring.II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the brake disc bolt or bolts (3) ,
-the brake disc.
REFITTING
I - REFITTING PREPARATION OPERATION
aClean the brake discs using a parts washer.
aDry the surface of the discs.
aClean the mating faces of the disc on the hub using
a wire brush and BRAKE CLEANER (see Vehicle:
Parts and consumables for the repair) (04B, Con-
sumables - Products).
aparts always to be replaced: Front brake disc
bolt
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the brake disc with new bolts.
aTorque tighten the new disc mounting bolts (see
30A, General information, Brake circuit: Tighten-
ing torque, page 30A-6)
125059
125056

33A-9
REAR AXLE COMPONENTS
Rear brake calliper mounting: Removal - Refitting
EQ UIPMENT LEVEL SPORT
33A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRelease the parking brake.
aRemove:
-the rear wheel (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) ,
-the rear brake pads (see 33A, Rear axle compo-
nents, Rear brake pads: Removal - Refitting,
page 33A-1) .aRemove:
-the brake calliper guide pin bolts (1) ,
-the brake calliper from the mounting.
aAttach the brake calliper to the suspension spring.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove:
-the brake calliper mounting bolts (2) ,
-the brake calliper mounting. Special tooling required
Fre. 1190-01Brake calliper piston return
tool.
Tightening torquesm
bolts of the brake calli-
per mountingXXX
new bolts of the brake
calliper guide pins105 N.m
WARNING
To avoid damaging the parking brake cable protec-
tors and causing premature wear of the system, do
not handle the cables with a tool.
132468
132465

33A-24
REAR AXLE COMPONENTS
Shock absorber: Removal - Refitting
33A
If a shock absorber is replaced, the shock absorber on
the opposite side must also be replaced.
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).aRemove the luggage compartment internal trim (1) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUndo the upper shock absorber nut (2) when the
wheels are on the ground.
aRaise the vehicle. Equipment required
component jack
Tightening torquesm
shock absorber lower
bolt105 Nm
shock absorber upper
nut21 Nm
WARNING
To prevent any damage, do not use the rear axle as
support for the lifting system.
WARNING
To prevent any suspension asymmetry, replace
both of the shock absorbers on the same axle.
WARNING
To avoid damaging the rear axle components
(elastic joints, brake hoses etc.) do not remove
both shock absorbers at the same time. Proceed
one side at a time.
119428
119434

33A-26
REAR AXLE COMPONENTS
Shock absorber: Removal - Refitting
G44
33A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 411, 02A, Lifting equip-
ment).
aRemove the luggage compartment interior trim (see
Rear loading trim: Removal - Refitting) (MR 412,
71A, Body internal trim).II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUndo the upper shock absorber nut (1) when the
wheels are on the ground.
aRaise the vehicle. Equipment required
component jack
Tightening torquesm
lower shock absorber
bolt105 Nm
shock absorber upper
nut21 Nm
WARNING
To prevent any damage, do not use the rear axle as
support for the lifting system.
WARNING
To prevent any suspension asymmetry, replace
both of the shock absorbers on the same axle.
WARNING
To avoid damaging the rear axle components
(elastic joints, brake hoses etc.) do not remove
both shock absorbers at the same time. Proceed
one side at a time.
119434

33A-28
REAR AXLE COMPONENTS
Rear suspension spring: Removal - Refitting
33A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift ( (see Vehicle:
Towing and lifting) ).
aRemove the rear wheels (see 35A, Wheels and ty-
res, Wheel: Removal - Refitting, page 35A-1) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aUsing a block, bring the component jack into con-
tact under the rear axle, near the shock absorber.
aMark the position where the springs are fitted.
aRemove the lower bolt (1) from the shock absorber.
aRemove the component jack.
aRepeat these operations on the opposite side.aRemove the springs by removing the component
jack.
aLeave the rear axle suspended.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aUsing a block, bring the component jack into con-
tact under the rear axle, near the shock absorber. Equipment required
component jack
Tightening torquesm
shock absorber lower
bolts105 Nm
119340
119547
119546

33A-29
REAR AXLE COMPONENTS
Rear suspension spring: Removal - Refitting
33A
aRefit the shock absorber springs into their housings.
aCompress the rear axle.
aRefit the lower shock absorber mounting bolts.
aTorque tighten the shock absorber lower bolts
(105 Nm).
II - FINAL OPERATION.
aRemove the component jack.
aRefit the rear wheels (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) .
119400

33A-34
REAR AXLE COMPONENTS
Rear stub axle carrier: Removal - Refitting
EQ UIPMENT LEVEL SPORT
33A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aRemove the rear wheel (see 35A, Wheels and ty-
res, Wheel: Removal - Refitting, page 35A-1) .aUnclip the parking brake cable from the calliper at
(1) .
aRemove:
-the brake calliper mounting bolts (2) ,
-the "brake calliper mounting - brake calliper" as-
sembly.
aAttach the "brake calliper mounting - brake calliper"
assembly to the suspension spring.
aRemove the rear brake disc (see 33A, Rear axle
components, Rear brake disc: Removal - Refit-
ting, page 33A-11) . Equipment required
component jack
Tightening torquesm
new bolts of the rear
stub axle carrier53 N.m
lower bolt of the rear
shock absorber105 N.m
new bolts of the brake
calliper mounting105 Nm
WARNING
To avoid damaging the parking brake cable protec-
tors and causing premature wear of the system, do
not handle the cables with a tool.
132468

33A-38
REAR AXLE COMPONENTS
Complete rear axle system: Removal - Refitting
33A
aUnclip the parking brake cables (3) on the reservoir.
aOpen the ABS sensor connector protective unit (4) .aDisconnect the ABS sensor connectors (5) .
aRemove:
-the brake hose lower unions (6) ,
-the rear suspension springs (see 33A, Rear axle
components, Rear suspension spring: Remov-
al - Refitting, page 33A-28) .
119652
119438
119437
119339

33A-42
REAR AXLE COMPONENTS
Complete rear axle system: Removal - Refitting
33A
2 - Refitting
aLower the lift.
aPosition the bearing centring devices (12) opposite
the centring holes.
aRefit the rear axle bearing bolts.
aTorque tighten the rear axle bearing bolts (62 Nm).
aRemove the safety strap(s).
aRaise the lift.
aRefit:
-the rear suspension springs (see 33A, Rear axle
components, Rear suspension spring: Remov-
al - Refitting, page 33A-28) ,
-the brake hose lower unions.
aTorque tighten the brake hose lower unions (17
Nm).
aConnect the ABS sensor connectors.
aClose the ABS sensor connector protective unit.
aClip the parking brake cables onto the reservoir.
aPosition the parking brake cables on the parking
brake compensator.
aCheck that the parking brake cable stops are proper-ly inserted in their housings.
III - FINAL OPERATION.
aAdjust the parking brake cables (see 37A, Mechan-
ical component controls, Parking brake lever:
Removal - Refitting, page 37A-46) .
aRefit the rear wheels (see 35A, Wheels and tyres,
Wheel: Removal - Refitting, page 35A-1) .
aRemove the pedal press.
aBleed the braking circuit (see 30A, General infor-
mation, Braking circuit: Bleed, page 30A-4) .
119651