engine RENAULT TWINGO 2009 2.G Electrical Equipment - Multimedia Connection Workshop Manual

86C-18V1 MR-413-X44-86C000$050.mif
86C
CBOX
Vdiag No.: 04
The mobile connectivity computer enables music files to be played (MP3, WMA, etc.) on:
•USB mobile peripherals (USB key, MP3 player, etc.) (Except hard disk with own power supply),
•audio peripherals via the jack socket.
The multimedia system offers the following possibilities:
•Choose FM radio stations using the presets, the list or manual selection.
•Have access to an automatically updated FM radio list.
•Listen to CDs and MP3s.
•Control the radio using the radio control satellite.
•Have access to optimised audio and acoustic telephone configurations for each vehicle according to the vehicle
type.
•Modify various acoustic parameters (base, treble, front/rear balance, etc.).
•Use the hands-free telephone function (sound relayed towards the radio speakers) with a Bluetooth telephone.
•Use voice recognition for the telephone functions (button on the radio control satellite). The voice identifier can be
recorded.
•Benefit from a connection for a CD changer.
•Possibility of connecting a peripheral with a USB port, Jack socket, etc.
•Has anti-theft protection
Computer activation system
The mobile connectivity computer has an activation system.
The mobile connectivity computer is activated under the following conditions:
•by pressing the radio ON/OFF button,
•by starting the engine.
The mobile connectivity computer is switched off under the following conditions:
•The ignition is switched off.
•Door opened (Clio III)
•Door opened for 1 minute (New Twingo)
•By pressing the radio ON/OFF button (Clio III and New Twingo).
The multimedia connection unit (Display or Multimedia connection unit ) is activated by the UCH (central door
unlocking); this then activates the multimedia computers (Navigation, Radio, mobile connectivity computer, etc.) via
the "Activation signal" connections.
MULTIMEDIA CONNECTION
Fault finding – Function

86C-25
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults using command RZ001 Fault memory.
Deal with any other faults.
V1 MR-413-X44-86C000$090.mif
MULTIMEDIA CONNECTION
Fault finding – Interpretation of faults86C
CBOX
Vdiag No.: 04
DF004
PRESENT
OR
STOREDBATTERY VOLTAGE
1.DEF: Undervoltage
NOTESConditions for applying fault finding procedures to stored faults:
The fault is declared present after:
–The + after ignition feed is activated,
–The multimedia system is switched on using the on/off button.
–The battery voltage is out of range (12 V < X < 15 V).
Use the Wiring Diagrams Technical Note for Clio III or New Twingo.
Remove the card from the reader or the key from the ignition, then check the condition of the battery.
Check the battery: leaks, incorrectly fitted, loosened battery terminal, and corrosion.
Check the earth connections of the vehicle: battery/chassis, engine/chassis, starter/engine, alternator/engine,
gearbox/chassis.
If the fault is detected, resolve the abnormal contact fault.
Check the battery and perform an alternator supply test (see 16A, Starting, Charging).
Check the conformity of the fuse of the fuse and relay box (use the Wiring Diagrams Technical Note for Clio III
or New Twingo):
–for New Twingo: F48 (15A),
–for Clio III: unit fuse 710 (15A) and F2 (20A) on component 260.
Replace the fuse if not correct.
Disconnect the connector of the mobile connectivity computer, component code 1959.
Check the continuity of the earth on connection NAM.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
CBOX_V04_DF004

86C-32V1 MR-413-X44-86C000$100.mif
86C
CBOX
Vdiag No.: 04
MAIN SCREEN
NOTESOnly carry out a conformity check after a complete check with the diagnostic tool. The
values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on.
FunctionParameter or Status
Check or ActionDisplay and
NotesFault finding
PeripheralET002:USB peripheralABSENT / PRESENT
Connect a peripheral to the USB
portIn the event of an
inconsistency, consult
the interpretation of
ALP2 My USB
peripheral cannot be
read.
ET003:JACK peripheralABSENT / PRESENT
Connect a musical peripheral to
the jack socket.In the event of an
inconsistency, consult
the interpretation of
ALP3 Auxiliary input
does not work.
Analogue
signal levelPR001:Analogue signal level,
right-hand track0 V < X < 4 VIn the event of an
inconsistency, consult
the interpretation of
ALP3 Auxiliary input
does not work.
PR002 Analogue signal level,
left-hand track0 V < X < 4 VIn the event of an
inconsistency, consult
the interpretation of
ALP3 Auxiliary input
does not work.
CBOX_V04_CCONF
MULTIMEDIA CONNECTION
Fault finding – Conformity check