RENAULT TWINGO 2009 2.G Electrical Equipment - Rev Counter Instrument User Guide

83E-11
MR-413-X44-83E000$504_eng.mif
V2
83E
REV COUNTER INSTRUMENT
Fault finding - Configuration
REV COUNTER CONFIGURATION
After configuring the rev counter, enter the vehicle identification number (VIN) using the command VP001 ENTER
VIN.Summary of available configuration readings
LC003: DIMMER LIGHTING
–YES
–NO
LC002: ELECTRONIC STABILITY CONTROL (ESP)
–WITH
–NONE
LC001: OVERSPEED INDICATOR LIGHT
–ABSENT
–PRESENT
Summary of available configurations
CF003: DIMMER LIGHTING
–YES
–NO
CF002: ELECTRONIC STABILITY CONTROL
–WITH
–NONE
CF001: OVERSPEED INDICATOR LIGHT
–ABSENT
–PRESENT

Vdiag No.: 04
MR-413-X44-83E000$504_eng.mif

83E-12
MR-413-X44-83E000$588_eng.mif
V2
83E
REV COUNTER INSTRUMENT
Fault finding - Conformity check
MAIN SCREEN
DISPLAY SUB-FUNCTION
NOTESOnly check conformity after a full check with the diagnostic tool. The values shown in
this conformity check are given as a guide.
Application conditions: Vehicle under + after ignition feed.
FunctionParameter or state checked
or actionDisplay and notes Fault finding
Rev counter
lightingET002:Side lights controlSide
lights onACTIVE
In the event of a fault, consult the
interpretation of status ET002
SIDE LIGHTS CONTROL. Side
lights offINACTIVE
FunctionParameter or state checked
or actionDisplay and notes Fault finding
DisplayAC001:Rev counter
indicator lightsActivating this lights up
all of the indicator lights
integrated
in the rev counter.Carry out fault finding on the
multiplex network (see 88B,
Multiplexing).
If the fault is still present, contact
the techline.
AC002:Back
lighting + needleActivating this lights up
the back of the
rev counter and needle.Carry out fault finding on the
multiplex network (see 88B,
Multiplexing).
If the fault is still present, contact
the techline.
AC003:Rev counter
needleActivating this moves the
needle: Position 0 then
mid-range position and
maximum value position.Carry out fault finding on the
multiplex network (see 88B,
Multiplexing).
If the fault is still present, contact
the techline.
CPT_V04_CCONF
Vdiag No.: 04
MR-413-X44-83E000$588_eng.mif

83E-13
MR-413-X44-83E000$588_eng.mif
V2
REV COUNTER INSTRUMENT
Fault finding - Conformity check

Vdiag No.: 04
83E
CONFIGURATION CHECK
ESP configuration check depending on equipment:
Check if the vehicle is fitted with the ESP system (ESP button on the console).
If the vehicle is fitted with the ESP system, when the + after ignition feed is switched on, the indicator light should
come on for 3 seconds. In the event of a fault, configure the rev counter using the command CF002 ELECTRONIC
STABILITY (ESP) CONTROL (see Configuration).
Dimmer lighting function check:
With the side lights on, activate the rev counter variation control, the rev counter lighting varies at the same time.
If the rev counter lighting does not change, check the configuration of the rev counter using configuration reading
LC003 DIMMER LIGHTING (see Configuration) and configure the rev counter in accordance with the requirements
using command CF003 DIMMER LIGHTING (see Configuration).

83E-14
MR-413-X44-83E000$672_eng.mif
V2
83E
REV COUNTER INSTRUMENT
Fault finding - Status summary table
Tool status Diagnostic tool title
ET002Side lights control

Vdiag No.: 04
MR-413-X44-83E000$672_eng.mif

83E-15
MR-413-X44-83E000$756_eng.mif
V2
83E
REV COUNTER INSTRUMENT
Fault finding - Interpretation of statuses
ET002
SIDE LIGHTS SWITCH
STATUS
DEFINITION–ACTIVE: This status indicates that the side light control is active.
–INACTIVE: This status indicates that the side light control is inactive.
NOTES–Ignition on.
–Side lights on.
If the status of the side light control remains at status INACTIVE, apply the following fault finding procedure.
Check fuse F43 (10A) of the passenger compartment fuse box, component code 1016.
Check that the connection and condition of the rev counter connector are correct (see Wiring Diagram Technical
Note, Twingo II, Component code 995).
If there is a repair method (see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair)
repair the connector, otherwise replace the wiring.
Check the + 12 V feed on connection LPG of component 995.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair) repair the wiring, otherwise replace it.
Check the continuity and insulation of:
Connection LPG between the passenger compartment fuse box, component code 1016 and the rev
counter, component code 995.
Connection MAM of the rev counter, component code 995.
Connection MAN of the rev counter, component code 995.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair) repair the wiring, otherwise replace it.
If the fault is still present, contact the techline.
CPT_V04_ET002

Vdiag No.: 04
MR-413-X44-83E000$756_eng.mif

83E-16
MR-413-X44-83E000$840_eng.mif
V2
83E
REV COUNTER INSTRUMENT
Fault finding - Customer complaints
NO DIALOGUE WITH THE COMPUTER ALP1
CPT_V04_ET002

Vdiag No.: 04
MR-413-X44-83E000$840_eng.mif

83E-17
MR-413-X44-83E000$924_eng.mif
V2
83E
REV COUNTER INSTRUMENT
Fault finding - Fault Finding Chart
ALP1 No dialogue with the computer
NOTESNone
Test the diagnostic tool on another vehicle which is in perfect working order.
Check that the sensor's green indicator light comes on.
If communication with the second vehicle is impossible, follow the instructions in the CLIP diagnostic tool test
section.
If dialogue with the second vehicle is possible, follow the instructions in the Vehicle check section.
DIAGNOSTIC
TOOL CHECK
Check the cleanliness and condition of the diagnostic socket contacts on the vehicle.
Check the condition of the cable from the diagnostic socket to the sensor, and the
cleanliness and condition of the connections.
Check the sensor connections.
Check the condition of the cable from the sensor to the CLIP tool, and the cleanliness
and condition of the connections.
Check the cleanliness and condition of the CLIP socket.
If the fault is still present, contact Techline.
Check the electrical voltage of the battery.
Check the cleanliness and condition of the battery terminals.
Check the condition of the battery earth cable and ensure that there is a good
electrical connection with the bodywork.
Check the condition and correct connection of the rev counter connector, component
code 995.
If there is a repair method (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair) repair the connector, otherwise replace the wiring.
Check rev counter supply fuse F18 (15 A) on the passenger compartment fuse box
component code 1016, and the status and cleanliness of the contacts.
Check the rev counter after ignition feed supply fuse F2 (15A) on the passenger
compartment fuse box, component code 1016, and the condition and cleanliness
of the contacts.
VEHICLE CHECK
CPT_V04_ALP01

Vdiag No.: 04
MR-413-X44-83E000$924_eng.mif

83E-18
MR-413-X44-83E000$924_eng.mif
V2

Vdiag No.: 04REV COUNTER INSTRUMENT
Fault finding - Fault Finding Chart83E
ALP1
CONTINUED
NOTESVehicle under + after ignition feed.
VEHICLE CHECK
Use the Universal bornier to check the following tracks on the vehicle diagnostic
socket:
Connection BP19 "+ protected battery feed" of the diagnostic socket, component
code 225.
Connection MAN "Right-hand dashboard cross member electronic earth" of the
diagnostic socket, component code 225.
Connection MAM "Left-hand dashboard cross member earth" of the diagnostic
socket, component code 225.
Check the earth of connections MAM and MAN of the rev counter, component
code 995.
If the earth of connections MAM and MAN is poor, check the insulation to + 12 V and
the continuity of the following connections:
MAM and MAN of the rev counter, component code 995.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the wiring, otherwise replace it.
Check for + 12 V on connection AP71 and connection BP6 of the rev counter,
component code 995.
If there is no + 12 V, check the insulation to earth and the continuity of the following
connections:
AP71 and BP6 of the rev counter, component code 995.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair) repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.