heating RENAULT TWINGO 2009 2.G Engine And Peripherals Passenger Compartment Connection Unit OBD User Guide

87B-92
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET028
CONTINUED
Check the insulation, continuity and absence of interference resistance of the following connections:
●Connection code 15A between components 319 and 645.
●Connection code 15M between components 319 and 645.
●Connection codes LPD and SP2 between components 319 and 1016.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the rear screen de-icing button (component code 319) (see MR 411
mechanical systems 61A heating control panel or 62B Climate control panel).
If the fault is still present, contact the Techline.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.

87B-93
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET029
AIR CONDITIONING BUTTON
NOTESNo faults should be present or stored.
Apply this status for vehicles with manual climate control or heating.
SPECIFICATIONSPRESSED
RELEASED
Check the configuration of the heating and air conditioning type of the vehicle:
–Check that LC013 "Air conditioning type" is "Heating" or "Manual" or "Automatic" according to the
equipment level. Otherwise carry out CF019 Air conditioning type.
Check the operation of the air conditioning button indicator light AC015 “Air conditioning button indicator
light”.
Check that fuses F29 (15A) and F42 (10 A) are sound and correctly fitted in the passenger compartment fuse and
relay box (component code 1016).
Replace the fuse(s) if necessary.
Check the air conditioning control panel black 9-track connector, (component code 319) (bent, oxidised or
broken tabs).
Check that the earth on connection NAM of the manual air conditioning control panel black 9-track connector is
in perfect condition.
Check for + 12 V accessories feed on connections LPD and SP2 of the manual air conditioning control panel
black 9-track connector.
Check the PE2 40-track connector of the UCH, component code 645 (tabs bent, oxidised, broken).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET029

87B -152
MR-413-X44-87B000$816.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
AC004
AC005
CENTRAL LOCKING
CENTRAL DOOR UNLOCKING
NOTESSpecial notes:
If the opening element motors are supplied too quickly and it is too difficult to test
using a multimeter, the measurements must be made using an oscilloscope.
No faults should be present or stored.
IMPORTANT
The door motors can perform 15 successive activations; beyond this there is a risk of the motors overheating and
being damaged.
NOTESNo faults should be present or stored.
Status ET463 “Door(s) or tailgate” must be “Open” when at least one of the
doors or tailgate is open and must be “Closed” when all of the doors and
tailgate are closed.
Note:
The tailgate lock (electric central door locking) must only be used to open the
luggage compartment and not to close it.
Check that fuses F14 (20 A) are sound and correctly fitted in the passenger compartment fuse and relay box
(for vehicles equipped with deadlocking function) (component code 1016).
Replace the fuse if necessary.
Check the condition and connection of the PE1, PE2 and PE3 connectors of the UCH (component code 645)
(tabs pushed back, oxidised, broken).
Check the condition and connection of the connectors of the electric locks of the driver's door (component
code 140), passenger door (component code 141) and the tailgate (component code 1322) (tabs pushed
back, oxidised, broken).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
AFTER REPAIRCarry out another fault finding check on the system.
UCH_V44_AC004 / UCH_V44_AC005
MR-413-X44-87B000$816.mif
UCH
Vdiag No.: 44