engine RENAULT TWINGO RS 2009 2.G Electrical Equipment - Instrument Panel Workshop Manual

83A-16
MR-413-X44-83A000$224.mif
V5
INSTRUMENT PANEL
Fault finding - Function

Vdiag No.: 04, 08
83A
–Illumination of the “battery charge” warning light:
Illumination of the “battery charge” warning light indicates the following statuses:
●Fixed illumination for three seconds when the + after ignition feed is switched on: Warning light test
phase by the instrument panel.
●Flashing: Low voltage.
If the “Stop” warning light and “Battery charge” warning light come on simultaneously, refer to the “Stop warning light
illumination” insert.
–Illumination of the “Oil pressure warning” warning light:
The “Oil pressure warning” warning light always comes on with the “Stop” warning light and the “Stop” buzzer
sounds. This warning light indicates a pressure fault in the engine lubrication circuit and indicates potential engine
damage.
This warning light comes on for 3 seconds when the + after ignition feed is activated (Test phase).
–Illumination of the “Coolant temperature warning” warning light:
The “coolant temperature warning” warning light always comes on with the “Stop” warning light and the “Stop”
buzzer sounds. This warning light indicates that the cooling circuit temperature is too high, and there is a risk of the
engine overheating and engine damage.
This warning light comes on for 3 seconds when the + after ignition feed is activated (Test phase).
–Illumination of the “ABS” warning light:
Illumination of the “ABS” warning light indicates the following statuses to the driver:
–Rapid flashing: ABS not configured.
–Slow flashing: ABS in configuration phase.
This warning light comes on for 3 seconds when the + after ignition feed is activated (Test phase).
If the “Service” warning light and “ABS” warning light come on simultaneously, refer to the “Service warning light
illumination” insert.

83A-17
MR-413-X44-83A000$224.mif
V5
INSTRUMENT PANEL
Fault finding - Function

Vdiag No.: 04, 08
83A
–Illumination of the “Particle filter” warning light:
Illumination of the “Particle filter” warning light indicates a minor particle filter fault to the driver.
If the “Service” warning light and “Particle filter” warning light come on simultaneously, refer to the “Service warning
light illumination” insert.
The New Twingo does not currently have a particle filter.
–Illumination of the “Major Electric Power-Assisted Steering fault warning” warning light:
Illumination of the “major electric power-assisted steering fault warning” warning light is requested by the electric
power-assisted steering up to 1 second after the engine is started.
If the “Stop” warning light and “Stop buzzer” are activated simultaneously, refer to the “Stop warning light
illumination” insert.
–Illumination of the “OBD” warning light
If the “OBD” warning light and “Service” warning lights come on simultaneously, refer to the “Service warning light
illumination” insert.
–Illumination of the “airbag fault” warning light:
Illumination of the “Airbag fault” warning light indicates an airbag warning light test phase by the instrument panel.
If the “Service” warning light and “Airbag fault” warning light come on simultaneously, refer to the “Service warning
light illumination” insert.
–Illumination of the “Passenger airbag disconnection” warning light:
Illumination of the “Passenger airbag disconnection” warning light indicates deactivation of the front passenger
airbag.

83A-26
MR-413-X44-83A000$448.mif
V5
INSTRUMENT PANEL
Fault finding - Interpretation of faults

Vdiag No.: 04, 08
83A
DF009
PRESENT
OIL PRESSURE SENSOR
1.DEF: Signal incoherent
NOTESSpecial note:
This check must be carried out with the engine stopped.
1.DEF
NOTESThe fault is declared present if the oil pressure sensor is not
detected as closed when the engine is stopped.
Top up the oil level before starting the check.
Look for any damage to the wiring harness and check the condition and connection of the oil pressure switch
and its connections.
Look for possible damage to the wiring harness, check the connection and condition of the instrument panel
connector.
If there is a repair method (see Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair)
repair the connector, otherwise replace the wiring.
Check the insulation and continuity of the following connection:
Connection 28A between component 205 and component 247.
If there is a repair method (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for
repair) repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
TDB_V04_DF009P / TDB_V08_DF009P

83A-29
MR-413-X44-83A000$504.mif
V5
83A
INSTRUMENT PANEL
Fault finding - Conformity check
MAIN SCREEN
SUB-FUNCTION: DISPLAY
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Vehicle with + after ignition feed activated, engine
stopped.
FunctionParameter or status checked
or actionDisplay and notes Fault finding
Instrument
panel lighting.ET004Side lights controlSide lights
onACTIVE
In the event of a fault, consult the
interpretation of status ET004
Side lights switch Side lights
offINACTIVE
FunctionParameter or status checked
or actionDisplay and notes Fault finding
Instrument
panel lightingET004:Side lights controlSide lights
onACTIVE
In the event of a fault, consult the
interpretation of status ET004
Side lights switch. Side lights
offINACTIVE
Direction
indicator signalET245:Direction indicatorsActivated ACTIVE
In the event of a fault, refer to the
interpretation of status ET245
Indicators. In rest
positionINACTIVE
Fault signalET248:Stop warning light
activated by the
system1- Injection
2-Coolant
temperature
3-Oil pressure
4-Brake fluid level
5- Electronic Braking
Distribution
6-Electric power-
assisted steering
7-Battery chargeSee the interpretation of ET248
STOP warning light activated
by the system.
TDB_V04_CCONF / TDB_V08_CCONF

Vdiag No.: 04, 08
MR-413-X44-83A000$504.mif

83A-30
MR-413-X44-83A000$504.mif
V5
INSTRUMENT PANEL
Fault finding - Conformity check

Vdiag No.: 04, 08
83A
SUB-FUNCTION: DISPLAY (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Vehicle with + after ignition feed activated, engine
stopped.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Fault signalET249:Service warning
light activated by
the system1-Multiplex line
communication
2- Injection
3-Water present in diesel
fuel
4-Sequential gearbox
5-Vehicle speed circuit
6-Cruise control/speed
limiter
7-ESP
8-ABS
9-Oil change interval
10- Particle filter
11- Airbag
12- OBDSee the interpretation of
ET249 SERVICE warning
light activated by the
system
Parking brake
signalET097:Parking brakeAutomatic
parking brake
onAPPLIED
In the event of a fault, consult
the interpretation of status
ET097 Parking brake Parking
brake
releasedRELEASED
Minimum brake
fluid level signalET019:Minimum brake
fluid levelMinimum
brake fluid
reservoir
levelYES
In the event of a fault, consult
the interpretation of status
ET019 Minimum brake fluid
level. Normal brake
fluid
reservoir
levelNO
Oil pressure
present signalET096:Oil pressure
contactEngine
runningOPENIn the event of a fault,
consult the interpretation of
fault DF009 “oil pressure
sensor” Engine
stoppedCLOSED

83A-31
MR-413-X44-83A000$504.mif
V5
INSTRUMENT PANEL
Fault finding - Conformity check

Vdiag No.: 04, 08
83A
SUB-FUNCTION: DISPLAY (CONTINUED)
SUB-FUNCTION: TRIP COMPUTER
*ADAC: Trip Computer
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Vehicle with + after ignition feed activated, engine
stopped.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Instrument panel
warning light
operation checkAC009:Instrument
panel warning
lightsIllumination of all of the
warning lights
simultaneously on the
displayImportant: This command
causes the Airbag system
stored fault to occur again
(see 88C Airbag and
pretensioners).
–Before running the
command:
Deal with all of the Airbag
faults.
(see 88C, Airbag and
pretensioners).
–After running the
command:
Clear the Airbag system
stored faults.
If one or more warning lights
do not come on, contact
Techline.
Backlighting
operation checkAC010:LightingGradual illumination of
the instrument panel
backlightingWITHOUT
Instrument panel
buzzer checkAC006:BuzzerInstrument panel buzzer
operation–If the buzzer is faulty,
contact Techline.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
ADAC* button
status signalET030:ADAC* scroll
button
Button
depressedDEPRESSED
In the event of a fault, consult the
interpretation of status ET030
ADAC* scroll button.
Button
releasedRELEASED
Clock setting
button status
signalET095:Clock setting
button
Button
depressedDEPRESSED
Contact the Techline.Button
releasedRELEASED

83A-32
MR-413-X44-83A000$504.mif
V5
INSTRUMENT PANEL
Fault finding - Conformity check

Vdiag No.: 04, 08
83A
SUB-FUNCTION : GAUGING
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Vehicle with + after ignition feed activated, engine
stopped.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Fuel sender
operation checkPR040:Current fuel levelThe current fuel level
depends on the vehicle
body movements.In the event of a fault, consult the
interpretation of fault DF007
Fuel sender circuit.
Filtered fuel
level checkPR041:Filtered fuel levelThe filtered fuel level is
independent of the
variations created by the
vehicle body movements.In the event of a fault, consult the
interpretation of parameter
PR041 Filtered fuel level.
Fuel sender
resistance
checkPR002:Fuel sender unit
resistanceThe fuel sender resistance
depends on the fuel level.
In reserve: 260 ΩΩ Ω Ω
Full: 38 ΩΩ Ω ΩIf R < 5 ΩΩ Ω Ω
or R> 350 ΩΩ Ω Ω
: Faulty
fuel sender.
In the event of a fault, consult the
interpretation of fault DF007
Fuel sender circuit.

83A-33
MR-413-X44-83A000$504.mif
V5
INSTRUMENT PANEL
Fault finding - Conformity check

Vdiag No.: 04, 08
83A
SUB FUNCTION: ODOMETRY IN KM
SUB FUNCTION: ODOMETRY IN MILES
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Vehicle with + after ignition feed activated, engine
stopped.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Check the
general distance
travelled by the
vehicle in kmPR025:Odometry in kmDisplays the vehicle
distance in km.WITHOUT
Check the
distance before
oil service in kmPR005:Distance to next oil
service: current
value in kmDisplays the distance
remaining in kms before
the recommended oil
service.WITHOUT
Check the
interval between
each oil service
in kmPR007:Oil change
frequency in km.Initial oil service interval
in km.WITHOUT
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Check the
general distance
travelled by the
vehicle in milesPR026:Odometer in milesDisplays the vehicle
distance in miles.WITHOUT
Check the
distance before
oil service
in milesPR023:Oil service
interval: current
value in milesDisplays the distance
remaining in miles before
the recommended oil
service.WITHOUT
Check the
interval between
each oil service
in milesPR024:Oil change
frequency in miles.Initial oil service interval in miles.