battery RENAULT TWINGO RS 2009 2.G Electrical Equipment Owner's Manual

85A-11
WIPING - WASHING
Windscreen wiper mechanism: Removal - Refitting
RIGHT-HAND DRIVE
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove:
-the windscreen wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) ,
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior equi-
pment).
II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove:
-the front windscreen wiper mechanism bolts (1) ,
-the windscreen wiper mechanism.aDisconnect the windscreen wiper motor connector
(2) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aConnect the windscreen wiper motor connector.
aRefit:
-the windscreen wiper mechanism,
-the windscreen wiper mechanism bolts.
II - FINAL OPERATION.
aRefit the scuttle panel grille (see Scuttle panel
grille: Removal - Refitting) (MR 412, 56A, Exterior
equipment).
aConnect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-2) .
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aRefit the windscreen wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) . WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
125232
125231
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.

85A-12
WIPING - WASHING
Windscreen wiper motor: Removal - Refitting
LEFT-HAND DRIVE
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove:
-the windscreen wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) ,
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior equi-
pment),
-the front windscreen wiper mechanism (see 85A,
Wiping - Washing, Windscreen wiper mecha-
nism: Removal - Refitting, page 85A-10) .
II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the windscreen wiper motor shaft nut (1) .
aExtract the mechanism drive linkage from the winds-
creen wiper motor shaft.aRemove:
-the bolts (2) from the windscreen wiper motor,
-the windscreen wiper motor (3) .
REFITTING
I - REFITTING PREPARATIONS OPERATION
aConnect:
-the windscreen wiper motor connector,
-the battery (see 80A, Battery, Battery: Removal -
Refitting, page 80A-2) .
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aDisconnect:
-the battery (see 80A, Battery, Battery: Removal -
Refitting, page 80A-2) ,
-the windscreen wiper motor connector.
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the windscreen wiper motor,
-the windscreen wiper motor bolts. WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
119390
119391
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.

85A-13
WIPING - WASHING
Windscreen wiper motor: Removal - Refitting
LEFT-HAND DRIVE
85A
aRefit:
-the mechanism drive linkage (4) , ensuring that it is
parallel to the axis connecting the two windscreen
wiper motor lower bolts (5) ,
-the windscreen wiper motor shaft nut.
III - FINAL OPERATION.
aRefit:
-the windscreen wiper mechanism (see 85A, Wi-
ping - Washing, Windscreen wiper mechanism:
Removal - Refitting, page 85A-10) ,
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior equi-
pment).
aConnect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-2) .
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aRefit the front wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) .
104932
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.

85A-14
WIPING - WASHING
Windscreen wiper motor: Removal - Refitting
RIGHT-HAND DRIVE
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove:
-the windscreen wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) ,
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior equi-
pment),
-the front windscreen wiper mechanism (see 85A,
Wiping - Washing, Windscreen wiper mecha-
nism: Removal - Refitting, page 85A-10) .II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the windscreen wiper motor shaft nut (1) .
aExtract the mechanism drive linkage from the winds-
creen wiper motor shaft.
aRemove:
-the bolts (2) from the windscreen wiper motor,
-the windscreen wiper motor (3) .
REFITTING
I - REFITTING PREPARATIONS OPERATION
aConnect:
-the windscreen wiper motor connector,
-the battery (see 80A, Battery, Battery: Removal -
Refitting, page 80A-2) .
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aDisconnect:
-the battery (see 80A, Battery, Battery: Removal -
Refitting, page 80A-2) ,
-the windscreen wiper motor connector. WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
125227
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.

85A-15
WIPING - WASHING
Windscreen wiper motor: Removal - Refitting
RIGHT-HAND DRIVE
85A
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the windscreen wiper motor,
-the windscreen wiper motor bolts.
aRefit:
-the mechanism drive linkage (4) , ensuring that it is
parallel to the axis connecting the two windscreen
wiper motor lower bolts (5) ,
-the windscreen wiper motor shaft nut.
III - FINAL OPERATION.
aRefit:
-the windscreen wiper mechanism (see 85A, Wi-
ping - Washing, Windscreen wiper mechanism:
Removal - Refitting, page 85A-10) ,
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior equi-
pment).
aConnect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-2) .
aMove the wiper stalk from (0) to (1), then from (1) to
(0).aRefit the windscreen wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) .
125227
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.

86A-5
RADIO
Radio aerial: Removal - Refitting
WITH 2 SPEAKERS, WITHOUT RADIO or WITH 4 SPEAKERS, WITHOUT RADIO or RADIO NO. 01 or RADIO
NO. 03
86A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove:
-the front seat belt upper bolt (see Front seat belt:
Removal - Refitting) (MR 412, 59A, Safety equip-
ment),
-the rear seat belt upper bolt (see Rear seat belt:
Removal - Refitting) (MR 412, 59A, Safety equip-
ment),
-the sun visor (see Sun visor: Removal - Refitting)
(MR 412, 57A, Interior equipment),
-the interior equipment covers (see Interior rear-
view mirror: Removal - Refitting) (MR 412, 57A,
Interior equipment),
-the A-pillar trims (see Windscreen pillar trim: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim),
-the rear parcel shelf side trims (see Rear parcel
shelf side trim: Removal - Refitting) (MR 412,
71A, Body internal trim),
-the rear panel trims (see Rear panel lining: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim),
-the rear quarter panel trims (see Quarter panel
trim: Removal - Refitting) (MR 412, 71A, Body in-
ternal trim),
-the B-pillar upper trims (see B-pillar upper trim:
Removal - Refitting) (MR 412, 71A, Body internal
trim),
-the headlining (see Headlining: Removal - Refit-
ting) (MR 412, 71A, Body internal trim).
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove the sunroof “motor - computer” assembly
(see 87D, Electric windows - Sunroof, Sunroof
opening motor: Removal - Refitting, page 87D-7)
.II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the radio aerial connector (1) .
aDisconnect the radio aerial connector (2) .
aRemove:
-the radio aerial nut (3) ,
-the radio aerial.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the radio aerial, OPENING ROOF
121086
121087

86A-6
RADIO
Radio aerial: Removal - Refitting
WITH 2 SPEAKERS, WITHOUT RADIO or WITH 4 SPEAKERS, WITHOUT RADIO or RADIO NO. 01 or RADIO
NO. 03
86A
-the radio aerial nut.
aConnect the radio aerial connectors.
II - FINAL OPERATION.
aRefit the sunroof “motor - computer” assembly (see
87D, Electric windows - Sunroof, Sunroof ope-
ning motor: Removal - Refitting, page 87D-7) .
aRefit:
-the headlining (see Headlining: Removal - Refit-
ting) (MR 412, 71A, Body internal trim),
-the B-pillar left-hand upper trims (see B-pillar up-
per trim: Removal - Refitting) (MR 412, 71A,
Body internal trim),
-the rear quarter panel trims (see Quarter panel
trim: Removal - Refitting) (MR 412, 71A, Body in-
ternal trim),
-the rear panel trims (see Rear panel lining: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim),
-the rear parcel shelf side trims (see Rear parcel
shelf side trim: Removal - Refitting) (MR 412,
71A, Body internal trim),
-the A-pillar trims (see Windscreen pillar trim: Re-
moval - Refitting) (MR 412, 71A, Body internal
trim),
-the interior equipment covers (see Interior rear-
view mirror: Removal - Refitting) (MR 412, 57A,
Interior equipment),
-the sun visor (see Sun visor: Removal - Refitting)
(MR 412, 57A, Interior equipment),
-the rear seat belt upper bolt (see Rear seat belt:
Removal - Refitting) (MR 412, 59A, Safety equip-
ment),
-the front seat belt upper bolt (see Front seat belt:
Removal - Refitting) (MR 412, 59A, Safety equip-
ment).aConnect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-2) .
aCarry out the necessary operations without the dia-
gnostic tool (see Battery: Initialisation) (MR 413,
80A, Battery).
OPENING ROOF
OPENING ROOF

86B-2
CAR PHONE
"Hands-free" microphone: Removal - Refitting
HANDS-FREE TELEPHONE KIT
86B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove the computer (see 86B, Car phone, Com-
puter: Removal - Refitting, page 86B-4) .
aUnclip the dashboard side panel (1) on the passen-
ger side.
aRemove the A-pillar trim on the passenger side (see
Windscreen pillar trim: Removal - Refitting) (71A,
Body internal trim).II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the “hands-free” microphone wire from the
A-pillar clips (2) .
aRemove the “hands-free” microphone wire from the
dashboard side panel.
121136
132407
132405

86B-3
CAR PHONE
"Hands-free" microphone: Removal - Refitting
HANDS-FREE TELEPHONE KIT
86B
aRemove the “hands-free” microphone from the hea-
dlining.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit the “hands-free” microphone with its wire as
shown in the diagram above.
aConnect the “hands-free” microphone connector to
the computer.II - FINAL OPERATION.
aRefit:
-the windscreen pillar trim (see Windscreen pillar
trim: Removal - Refitting) (71A, Body internal
trim),
-the dashboard side panel,
-the computer (see 86B, Car phone, Computer:
Removal - Refitting, page 86B-4) .
aConnect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-2) .
132406
132410

86B-4
CAR PHONE
Computer: Removal - Refitting
HANDS-FREE TELEPHONE KIT
86B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the computer.
aDisconnect the computer connectors (1) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aConnect the computer connectors.
aRefit the computer in its original position.II - FINAL OPERATION.
aConnect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-2) .
aIf replacing the computer, carry out the necessary
operations using the Diagnostic tool (see Fault fin-
ding - Replacement of components) (86B, Car
phone). Equipment required
Diagnostic tool
Note:
The computer is secured under the glovebox by a
self-fastening strip.
132408