RENAULT TWINGO RS 2009 2.G Engine And Peripherals Passenger Compartment Connection Unit OBD Manual PDF

87B-71
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: ACCESS
* SR: Sunroof.
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
TailgateET061:Open tailgate
requestPRESENT
ABSENTIn the event of a fault, apply the
interpretation of status
ET061.
ET463:Door(s) or tailgateOPEN
CLOSEDIn the event of a fault, apply the
interpretation of status
ET463.
Locking/unlocking
buttonET186:Short press on door
closing buttonSignal can be
interpreted if the
ignition is switched off
(key removed from the
ignition switch).
ACTIVE = Remote
control door closing
button pressed for
longer than 2 seconds.
INACTIVE = Button not
pressed or pressed for
less than 2 seconds.In the event of a fault, refer to
the interpretation of status
ET186.
ET189:Long press on door
opening buttonACTIVE
INACTIVEIn the event of a fault, refer to
the interpretation of status
ET189.
Electric central locking
buttonET044:Central Locking
buttonDEPRESSED
RELEASEDIn the event of a fault, refer to
the interpretation of status
ET044.
One touch window /
SR*.ET087:One-touch window /
SR* authorisation.PRESENT
ABSENTIn the event of a fault, apply the
interpretation of status
ET087.
Locking commandAC004:Central door lockingThis command is used
to test whether central
door locking is workingIn the event of a fault, consult
the procedure for dealing
with command AC004.

87B-72
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: ACCESS (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and
NotesFault finding
Deadlocking
commandAC035:DeadlockingThis command is used to test
the operation of the
deadlocking, if the vehicle is
configured WITH deadlocking.In the event of a fault, refer
to the interpretation of fault
DF133.
Door unlocking
switchAC005:Central door
unlockingThis command is used to test
whether the 4 doors, tailgate
and fuel filler flap unlocking
function is operating correctly.In the event of a fault,
consult the procedure for
dealing with command
AC005.
Tailgate opening
controlAC061:Tailgate openingThis command is used to test
whether the tailgate opening
motor is working.In the event of a fault,
consult the procedure for
dealing with command
AC061.

87B-73
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: STARTING
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
EngineET239:Ignition switch
positionINACTIVE
+ ACCESSORIES
+ after ignition feed.
+ START FEEDIn the event of a fault, refer to the
interpretation of status ET239.
(See 17B, Petrol Injection,
Conformity check, Protection) or
(see 13B, Diesel Injection,
Conformity check, Protection).
ET142:Engine operating
phaseSTOPPED
STARTING
RUNNING
STALLEDIn the event of a fault, refer to the
interpretation of status ET142.
(See 17B, Petrol Injection,
Conformity check, Protection) or
(see 13B, Diesel Injection,
Conformity check, Protection).
PR025:Engine speed0 rpmIn the event of a fault, carry out a fault
finding on the multiplex network
(see 88B).
(See 17B, Petrol Injection,
Conformity check, Protection) or
(see 13B, Diesel Injection,
Conformity check, Protection).

87B-74
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
FUNCTION: AIR CONDITIONING
SUB-FUNCTION: USER SELECTION
* CPE: Electric central door locking.
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and
NotesFault finding
User selectionET028:Heated rear screen
buttonDEPRESSED
RELEASEDIn the event of a fault, refer to
the interpretation of status
ET028.
ET029:Air conditioning
buttonDEPRESSED
RELEASEDIn the event of a fault, refer to
the interpretation of status
ET029.
ET015:Passenger
compartment blowerRUNNING
STOPPEDIn the event of a fault, refer to
the interpretation of status
ET015.
AC015:Air conditioning
button indicator lightThis command is used to test
the operation of the air
conditioning button indicator
light.In the event of a fault, refer to
the interpretation of DF042.
AC019:Heated rear screen
indicator lightThis command is for testing
operation of the heated rear
screen indicator light.In the event of a fault, refer to
the interpretation of DF041.
AC020:CPE* button
indicator lightThis command is used to
operate the electric central
locking button.In the event of a fault, refer to
the interpretation of DF082.
AC052:Hazard warning
lights indicator lightThis command is used to
activate the hazard warning
lights.In the event of a fault, refer to
the interpretation of DF134.

87B-75
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
FUNCTION: AIR CONDITIONING
SUB-FUNCTION: HEATING
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
HeatingET015:Passenger
compartment
blowerRUNNING
STOPPEDIn the event of a fault, consult the
interpretation of status ET015.
ET239:Ignition switch
position+ after ignition feed.
STARTING
ACCESSORIES FEEDIn the event of a fault, refer to the
interpretation of status ET239.
PR025:Engine speed0 rpmIn the event of a fault, carry out a fault
finding on the multiplex network
(see 88B).
And (see 17B, Petrol Injection,
Conformity check, Protection) or
(see 13B, Diesel Injection,
Conformity check, Protection).
PR001:Battery voltage9 V < X < 16 VIn the event of a fault, run fault finding
on the charging circuit (see 80A,
Battery).
PR002:External
temperature˚CIn the event of a fault, refer to the
interpretation of parameter PR002.
PR024:Engine coolant
temperature˚CIn the event of a fault (see 17B,
Petrol Injection, Conformity check,
Protection) (see 13B, Diesel
Injection, Conformity check,
Protection).
AC060:Rear screen de-
icerThis command is used to
test the operation of the
rear screen de-icer.In the event of a fault, refer to the
interpretation of command AC060.
AC110:Temperature
displayImportant: this command
lasts approximately
30 seconds.
This command is for testing
the display.In the event of a fault, refer to the
interpretation of command AC110.

87B-76
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
FUNCTION: AIR CONDITIONING
SUB-FUNCTION: COLD LOOP
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
Cold loopPR002:External
temperature˚CIn the event of a fault, refer to the
interpretation of parameter
PR002.
ET142:Engine operating
phaseSTOPPED
STARTING
RUNNING
STALLEDIn the event of a fault, refer to the
interpretation of status ET142.
ET015:Passenger
compartment
blowerRUNNING
STOPPEDIn the event of a fault, refer to the
interpretation of status ET015.
ET030:Air conditioning
requestThis request is sent by the
UCH to the engine
management computer.
There are two possible
scenarios:
1
st scenario: vehicle equipped
with manual air conditioning.
The request is made by
pressing the air conditioning
button.
2
nd scenario: vehicle
equipped with climate control.
The request is made following
a user request or climate
control computer request.In the event of a fault, refer to the
interpretation of status ET030.
PR025:Engine speed0 rpmIn the event of a fault, run fault
finding on the multiplex network
(see 88B, Multiplex) then run
fault finding on the injection
system (see 13B, Diesel
injection or 17B, Petrol
injection).

87B-77
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
LIGHTING FUNCTION
SUB-FUNCTION: LIGHTING CONTROL
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
Lighting controlET081:Lighting switch
positionSIDE
DIPPED
MAIN BEAM
HEADLIGHTS
HAZARD LIGHTSIn the event of a fault, refer to the
interpretation for status ET081.
ET085:Hazard warning
lights buttonDEPRESSED
RELEASEDIn the event of a fault, refer to the
interpretation for status ET085.
Lighting requestET115:Request to switch on
lights by light sensorPRESENT
ABSENTIn the event of a fault, refer to the
interpretation for status ET115.
ET111:Front fog lights
requestPRESENT
ABSENTIn the event of a fault, refer to the
interpretation for status ET111.
ET082:Rear fog lights
requestPRESENT
ABSENTIn the event of a fault, refer to the
interpretation for status ET082.
ET083:Left-hand indicator
requestPRESENT
ABSENTIn the event of a fault, refer to the
interpretation of statuses
ET083 and ET084.
ET084:Right-hand indicator
requestPRESENT
ABSENT
TailgateET463:Door(s) or tailgateOPEN
CLOSEDIn the event of a fault, consult the
interpretation of status ET463.
Vehicle speedPR008:Vehicle speed0 mphIn the event of a fault, run fault
finding on the ABS system (see
38C, Anti-lock braking system).

87B-78
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: LIGHTING OUTPUT
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
Front fog lightsAC008:Front fog lightsThis command is used to
activate the front fog
light.In the event of a fault, apply the
interpretation of DF108.
Rear fog lightsAC009:Rear fog lightsThis command is used to
activate the rear fog light.In the event of a fault, apply the
interpretation of DF109.
Direction indicatorsAC022:Left-hand
direction
indicatorsThis command is used to
activate the left-hand
direction indicators.In the event of a fault, refer to the
interpretation for fault DF013
Left-hand direction indicator
circuit.
AC023:Right-hand
direction
indicatorsThis command is used to
activate the right-hand
direction indicators.In the event of a fault, refer to the
interpretation for fault DF012
Right-hand direction indicator
circuit.
LightsAC055:Side lightsThis command enables the
side lights to be activated.In the event of a fault, apply the
interpretation of DF087.
AC054:Dipped
headlightsThis command enables the
dipped beam headlights to
be activated.In the event of a fault, apply the
interpretation of DF088.

87B-79
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: LIGHTING OUTPUT (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and
NotesFault finding
Lights (continued)AC062:Main beam
headlightsThis command enables the
headlights to be activated.In the event of a fault, apply the
interpretation of DF098.
AC063:Progressive
switching on and off
of the courtesy lightThis command is used to
check that the gradual
courtesy light activation and
deactivation function is
operating correctly.In the event of a fault, apply the
interpretation of DF139.
Temperature
displayAC110:Temperature display Controls the display.In the event of a fault, apply the
interpretation of command
AC110.

87B-80
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: WIPING CONTROL
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
Wiper controlET077:Wiper stalk positionINACTIVE
INTERMITTENT
LOW-SPEED
HIGH SPEEDIn the event of a fault, apply the
interpretation of status ET077.
ET096:Wiper stalk
intermittent speed
ring position1
2
3
4
5In the event of a fault, apply the
interpretation of status ET096.
ET114:Windscreen wiper
request by rain
sensorABSENT
LOW-SPEED
HIGH SPEEDIn the event of a fault, apply the
interpretation of status ET114.
Windscreen wiper
park positionET078:Windscreen washer
requestACTIVE
INACTIVEIn the event of a fault, apply the
interpretation of status ET078.
ET027:Windscreen wiper
park positionACTIVE
INACTIVEIn the event of a fault, apply the
interpretation of status ET027.
Rear screen wiper
park positionET079:Rear screen washer
requestACTIVE
INACTIVEIn the event of a fault, apply the
interpretation of status ET079.
ET097:Rear screen wiper
park positionACTIVE
INACTIVEIn the event of a fault, apply the
interpretation of fault ET097.
ET080:Windscreen
rear screen wiperACTIVE
INACTIVEIn the event of a fault, apply the
interpretation of status ET080.
Reverse gearET109:Reverse gear
engagedYES
NOIn the event of a fault, apply the
interpretation of status ET109.