tailgate RENAULT TWINGO RS 2009 2.G Engine And Peripherals Passenger Compartment Connection Unit OBD Workshop Manual

87B-7
MR-413-X44-87B000$096.mif
V5
87B
ENGINE HARNESS
FRONT ENGINE WIRING & ADDITIONAL HEADLIGHTS
DOOR WIRING
CEILING WIRING
PASSENGER COMPARTMENT WIRING
REAR BUMPER WIRING
TAILGATE WIRING
1UCH
2Passenger Compartment Relay/Fuse Box
3Electric power-assisted steering.
4Transponder ring.
5Air conditioning panel.
6One touch window/anti-pinch module.
7Exterior temperature sensor.
8Rain/light sensor & interior temperature sensor.
9Anti-pinch/sunroof.
2ABS computer.
2Injection computer.
3Preheating unit.
4Sequential gearbox computer.
5Engine fuse and relay box.
6Alternator.
7
2
61
2
3
5
4
8
5
7
43
1
6
9
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding
- List and location of components
MR-413-X44-87B000$096.mif
UCH
Vdiag No.: 44

87B-11
MR-413-X44-87B000$192.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Role of components87B
Functions managed by the different UCH ranges on the New Twingo:
* CPE: Electric central door locking
* CAR: Automatic locking when drivingL1
Entry levelL2
Mid-rangeL3
Top of the
range
UCH reprogrammingXX X
Multiplex connectionXX X
Fault findingXX X
Access - Protection X X X
Transponder keyX
Transponder and radiofrequency keyXX
Engine immobiliserXX X
+ Accessories feed controlXX X
Alarm management (predisposition)XX
Locking and unlocking using electric central door locking buttonXX
DeadlockingX
Locking when driving (CAR*)XX
Automatic unlocking (in the event of impact)XX
Engine thermal protectionXX X
Automatic re-lockingXX
One-touch electric windowsX
Tailgate electric lockXX X
Tailgate opening switchXX X
Tailgate locking switch (with key)X
Air conditioning
Electric heated rear screen managementXX X
Air conditioning request managementXX
Automatic climate control management (via CAN network)XX
External temperature managementXX

87B-57
MR-413-X44-87B000$432.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF133
PRESENT
OR
STOREDDEADLOCKING MOTOR(S) CIRCUIT
CC.1: Short circuit to + 12 volts
CO.0: Open circuit or short circuit to earth
NOTESConditions for applying the fault finding procedure to stored faults:
If the fault reappears as present after:
The ignition is switched on and the deadlocking button has been pressed.
OR
Activation of AC035 Deadlocking.
Check that LC003 Deadlocking is definitely With. Otherwise, perform CF009
Deadlocking.
Check that LC040 Locking when driving is definitely With. Otherwise, perform
CF008 Locking when driving.
Ensure that the central door locking is correctly fixed; there must be no objects
preventing the central door locking from operating correctly.
Check that the doors and tailgate are closed correctly during the electrical
checks.
Check the presence and condition of fuse F14 (20 A) in the passenger compartment fuse and relay box
(component code 1016).
Replace the fuse if necessary.
Check the condition and connection of connectors PE1, PE2 and PE3 of the UCH (component code 645) (tabs
bent, oxidised, broken).
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition and connection of the electric central door locking connectors for the driver's and passenger's
doors (tabs bent, oxidised, bent etc.).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
When deadlocking, check the signal status on components 140 and 141 of the following connections using an
oscilloscope (refer to test1 Central door locking).
Right or left-hand door locks:
Oscilloscope red test pin on connection 20AP of component 140 or 141.
Oscilloscope black test pin on connection 20C of component 140 or 141.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF133

87B-65
MR-413-X44-87B000$432.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults
UCH
Vdiag No.: 44
87B
DF139
PRESENT
OR
STOREDCOURTESY LIGHT
CC.1: Short circuit to + 12 volts
NOTESThe fault is declared present after:
Opening at least one door.
OR
Running AC063 Switching the interior lights on and off.
Check the correct operation of status ET463 Door(s) or tailgate.
Check the condition and connection of the 6-track connector of the front interior lighting (component code 213)
and connector PE1 of component 645 (tabs bent, oxidised, broken).
Check for + 12 V on connection BPT of component 213.
Check the continuity and insulation of the following connections:
●Connection code BTP, between components 213 and 645.
●Connection code 13E between components 213 and 645.
●Connection code MAM between component 213 and earth MAM.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the operation of the rabbet switches using ET463 Door(s) and tailgate.
If the supply, earths and connections are correct, replace the courtesy light (component code 213).
(See MR 411, Mechanical 81B, Interior lighting, courtesy light: Removal - Refitting).
If the problem is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_DF139

87B-71
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: ACCESS
* SR: Sunroof.
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
TailgateET061:Open tailgate
requestPRESENT
ABSENTIn the event of a fault, apply the
interpretation of status
ET061.
ET463:Door(s) or tailgateOPEN
CLOSEDIn the event of a fault, apply the
interpretation of status
ET463.
Locking/unlocking
buttonET186:Short press on door
closing buttonSignal can be
interpreted if the
ignition is switched off
(key removed from the
ignition switch).
ACTIVE = Remote
control door closing
button pressed for
longer than 2 seconds.
INACTIVE = Button not
pressed or pressed for
less than 2 seconds.In the event of a fault, refer to
the interpretation of status
ET186.
ET189:Long press on door
opening buttonACTIVE
INACTIVEIn the event of a fault, refer to
the interpretation of status
ET189.
Electric central locking
buttonET044:Central Locking
buttonDEPRESSED
RELEASEDIn the event of a fault, refer to
the interpretation of status
ET044.
One touch window /
SR*.ET087:One-touch window /
SR* authorisation.PRESENT
ABSENTIn the event of a fault, apply the
interpretation of status
ET087.
Locking commandAC004:Central door lockingThis command is used
to test whether central
door locking is workingIn the event of a fault, consult
the procedure for dealing
with command AC004.

87B-72
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
SUB-FUNCTION: ACCESS (CONTINUED)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and
NotesFault finding
Deadlocking
commandAC035:DeadlockingThis command is used to test
the operation of the
deadlocking, if the vehicle is
configured WITH deadlocking.In the event of a fault, refer
to the interpretation of fault
DF133.
Door unlocking
switchAC005:Central door
unlockingThis command is used to test
whether the 4 doors, tailgate
and fuel filler flap unlocking
function is operating correctly.In the event of a fault,
consult the procedure for
dealing with command
AC005.
Tailgate opening
controlAC061:Tailgate openingThis command is used to test
whether the tailgate opening
motor is working.In the event of a fault,
consult the procedure for
dealing with command
AC061.

87B-77
MR-413-X44-87B000$480.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87B
LIGHTING FUNCTION
SUB-FUNCTION: LIGHTING CONTROL
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
Lighting controlET081:Lighting switch
positionSIDE
DIPPED
MAIN BEAM
HEADLIGHTS
HAZARD LIGHTSIn the event of a fault, refer to the
interpretation for status ET081.
ET085:Hazard warning
lights buttonDEPRESSED
RELEASEDIn the event of a fault, refer to the
interpretation for status ET085.
Lighting requestET115:Request to switch on
lights by light sensorPRESENT
ABSENTIn the event of a fault, refer to the
interpretation for status ET115.
ET111:Front fog lights
requestPRESENT
ABSENTIn the event of a fault, refer to the
interpretation for status ET111.
ET082:Rear fog lights
requestPRESENT
ABSENTIn the event of a fault, refer to the
interpretation for status ET082.
ET083:Left-hand indicator
requestPRESENT
ABSENTIn the event of a fault, refer to the
interpretation of statuses
ET083 and ET084.
ET084:Right-hand indicator
requestPRESENT
ABSENT
TailgateET463:Door(s) or tailgateOPEN
CLOSEDIn the event of a fault, consult the
interpretation of status ET463.
Vehicle speedPR008:Vehicle speed0 mphIn the event of a fault, run fault
finding on the ABS system (see
38C, Anti-lock braking system).

87B-84
MR-413-X44-87B000$528.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
*CPE: Electric central door locking
*RF: radio frequencyTool status Diagnostic tool title
ET008Blank UCH
ET015Passenger compartment blower
ET027Windscreen wiper park position
ET028Heated rear screen button
ET029Air conditioning button
ET030Air conditioning request 2
ET044CPE* button
ET045RF* signal. received
ET046Engine immobiliser
ET047Brake pedal position
ET061Open tailgate request
ET077Wiper stalk position
ET078Windscreen washer request
ET079Rear screen washer request
ET080Rear screen wiper request
ET081Lighting switch position
ET082Rear fog lights request
ET083Left-hand indicator request
MR-413-X44-87B000$528.mif
UCH
Vdiag No.: 44

87B-85
MR-413-X44-87B000$528.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table87B
*SR: Sunroof.
*RF: radio frequencyTool status Diagnostic tool title
ET084Right-hand indicator request
ET085Hazard warning lights button
ET087One-touch window/SR* authorisation
ET096Wiper intermittent speed ring position
ET097Rear screen wiper park position
ET109Reverse gear engaged
ET111Front fog lights request
ET114Wiping request via rain sensor
ET115Request to switch on lights by light sensor
ET142Engine operating phase
ET181Key allocated to the vehicle
ET185Key code received
ET186Short press on door closing button
ET189Long press on door opening button
ET193RF* signal from a key allocated to the vehicle
ET229Injection immobiliser code
ET239Ignition switch position
ET240Key frequency (in Hz)
ET250Injection
ET463Door(s) or tailgate

87B -102
MR-413-X44-87B000$576.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET061
TAILGATE OPENING REQUEST
NOTESNo faults should be present or stored.
IMPORTANT
On entry level vehicles (without central door locking), it is necessary to open the
tailgate mechanically using the key.
SPECIFICATIONSPRESENT
ABSENT
Check the following configuration:
–Check that LC093 Central door locking is With. Otherwise perform CF192 Central door locking.
Check the condition and connection of the tailgate lock connector (bent, broken tabs, etc.).
Check the condition and connection of the PE1 connector of the UCH, (component code 645) (tabs bent,
broken, etc.).
Check that the earth on connection MYH of the tailgate switch and tailgate lock are in perfect condition.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
When unlocking, check the signal status on component 1391 of the following connections using an oscilloscope
(refer to test1 “Central door locking”).
Tailgate lock:
Oscilloscope red test pin on connection 20S of
component 1322Oscilloscope black test pin on connection MYH
of component 1322
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET061