fuel RENAULT TWINGO RS 2009 2.G Engine And Peripherals Workshop Manual

17B-5
PETROL INJECTION
Petrol injection: List and location of components
D4F, and 780 or 782
17B
122387
(1) Fuel vapour recirculation sole-
noid valve
(2) Upstream oxygen sensor
(3) Petrol injection computer
(4) Motorised throttle valve
(5) Ignition coil
(6) Engine compar tment connec-
tion unit
(7) Intake distributor pressure sen-
sor
(8) Turbocharger
108254
(9) Fuel injection computer

17B-6
PETROL INJECTION
Petrol injection: List and location of components
D4F, and 780 or 782
17B
121764
(10) Throttle valve
108802
(11) Fuel vapour recirculation sole-
noid valve
120958
(12) Ignition coil
120957
(13) Upstream oxygen sensor

17B-9
PETROL INJECTION
Petrol injection: List and location of components
K4M
17B
131776
(1) Fuel vapour absorber bleed
solenoid valve
(2) Camshaft dephaser solenoid
valve
(3) Air inlet pressure sensor
(4) Coil
(5) Throttle valve
(6) Petrol injection computer
(7) Switching protection unit
(8) Coolant temper ature sensor
(9) Camshaft position sensor
(10) Pinking sensor
(11) Oil pressure sensor
(12) Air temperature sensor
(13) Injector rail
131766
(1) Fuel vapour absorber bleed
solenoid valve

17B-15
PETROL INJECTION
Oxygen sensors: Removal - Refitting
D4F, and 780 or 782
17B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
1 - Removing the upstream oxygen sensor
aRemove the air filter unit (see 12A, Fuel mixture,
Air filter unit: Removal - Refitting, page 12A-13) .aDisconnect the upstream oxygen sensor connector
(1) .
aUnclip the upstream oxygen sensor connector from
the rocker cover.
aUnclip the upstream oxygen sensor wiring (2) .
aRemove:
-the bolts (3) from the exhaust manifold heat shield,
-the turbocharger heat shield,
-the upstream oxygen sensor (4) from the catalytic
converter using the tool (Mot. 1495-01). Special tooling required
Mot. 1495-0122 mm socket for removal -
refitting of oxygen sensors.
Tightening torquesm
upstream oxygen sen-
sor45 N.m
turbocharger heat shield
bolts8 N.m
downstream oxygen
sensor45 N.m
WARNING
Do not use any product designed to improve the
electr ical contact in the injection computer and oxy-
gen sensor connectors or on the bodies of the oxy-
gen sensors.
Failure to respect this advice causes the oxygen
sensor to malfunction and results in failure to com-
ply with the emission control standard.
WARNING
If the connections are corroded, repair the wiring
(see Wiring: Precautions for repair) (Technical
Note 6015A, 88A, Wiring).
120957
120957

17B-16
PETROL INJECTION
Oxygen sensors: Removal - Refitting
D4F, and 780 or 782
17B
2 - Removal of the downstream oxygen sensor
aDisconnect the catalytic converter downstream oxy-
gen sensor connector (5) .
aUnclip the downstream oxygen sensor connector
from the catalytic converter.
aUnclip the wiring of the catalytic converter down-
stream oxygen sensor at (6) .
aRemove the downstream oxygen sensor (7) from
the catalytic converter using the tool (Mot. 1495-01).
REFITTING
REFITTING OPERATION FOR PART CONCERNED
1 - Refitting the upstream oxygen sensor
aRefit the upstream oxygen sensor.
aTorque tighten the upstream oxygen sensor (45
N.m) using the (Mot. 1495-01).
aRefit:
-the turbocharger heat shield,
-the turbocharger heat shield bolts.
aTorque tighten the turbocharger heat shield bolts
(8 N.m).
aClip:
-the upstream oxygen sensor wiring,
-the upstream oxygen sensor connector onto the
rocker cover.aConnect the upstream oxygen sensor connector.
aRefit the air filter unit (see 12A, Fuel mixture, Air fil-
ter unit: Removal - Refitting, page 12A-13) .
2 - Refitting the downstream oxygen sensor
aRefit the downstream oxygen sensor.
aTorque tighten the downstream oxygen sensor
(45 N.m) using the tool (Mot. 1495-01).
aClip the downstream oxygen sensor wiring onto the
catalytic converter.
aClip the downstream oxygen sensor connector onto
the catalytic converter.
aConnect the downstream oxygen sensor connector.
121774

17B-25
PETROL INJECTION
Crankshaft position sensor: Removal - Refitting
D4F or D7F
17B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the air filter box (see 12A, Fuel mixture,
Air filter unit: Removal - Refitting, page 12A-13) .
aRemove the engine wiring bolt from the gearbox.
aMove the engine wiring harness to one side.
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aDisconnect the engine speed and position sensor
connector.
aRemove the bolts (1) from the engine speed and po-
sition sensor.
aRemove the engine speed and position sensor.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the engine speed and position sensor,
-the engine speed and position sensor bolts.aConnect the engine speed and position sensor con-
nector.
II - FINAL OPERATION.
aConnect the engine wiring to the gearbox.
aRefit the engine wiring bolt to the gearbox.
aRefit the air filter box (see 12A, Fuel mixture, Air fil-
ter unit: Removal - Refitting, page 12A-13) . D4F
121409
D4F

17B-27
PETROL INJECTION
Injector rail - Injectors: Removal - Refitting
D4F, and 772
17B
PARTS AND CONSUMABLES FOR THE
REPAIR WORK
aPièces à remplacer systématiquement :
-injector O-ring's,
-injector retaining clips.
REMOVAL
I - REMOVAL PREPARATION OPERATION
aDisconnect the battery (see Battery: Removal - Re-
fitting) ).
aRemove:
-the air filter box (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) ,
-the intake distributor (see 12A, Fuel mixture, Inlet
distributor: Removal - Refitting, page 12A-29) .II - OPERATION FOR REMOVAL OF PART
CONCERNED
On the workbench
aDisconnect the injector wiring harness.
aRemove:
-the injector rail bolts (1) ,
-the injector rail,
-the injector wiring harness.
aRemove:
-the clips (2) from the injectors, IMPORTANT
During this operation, be sure to:
-refrain from smoking or bringing red hot objects
close to the working area,
-be careful of fuel splashes when disconnecting
the union.
IMPORTANT
Wear latex gloves during the operation.
107885
101492

17B-28
PETROL INJECTION
Injector rail - Injectors: Removal - Refitting
D4F, and 772
17B
-the injectors (3) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aRefit:
-the injectors,
-the injector clips,
-the injector wiring harness,
-the injector rail,
-the injector rail bolts.
aConnect the injector wiring harness.
II - FINAL OPERATION.
aRefit:
-the intake distributor (see 12A, Fuel mixture, Inlet
distributor: Removal - Refitting, page 12A-29) ,
-the air filter box (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) .
aConnect the battery (see Battery: Removal - Refit-
ting) ).

17B-29
PETROL INJECTION
Injector rail - Injectors: Removal - Refitting
D4F, and 780 or 782
17B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aDisconnect the battery (see ) (80A, Battery).
a
aDisconnect the air filter unit air inlet pipe (3) on the
air filter unit cover.
aMove aside the air inlet pipe from the air filter unit.
aRemove the bolt (4) of the intercooler air inlet pipe
from the throttle valve. Tightening torquesm
injector rail - injector
bolts4.5 N.m
IMPORTANT
During this oper ation, be sure to:
-refrain from smoking or bringing red hot objects
close to the working area,
-be careful of fuel splashes when disconnecting the
union.
IMPORTANT
Wear goggles with side protectors for this opera-
tion.
IMPORTANT
Wear leaktight gloves (Nitrile type) for this opera-
tion.
122833
122673
Note:
If the tightening clip (1) of the intercooler air inlet
pipe is removed, the flexible rubber pipe (2) and
the tightening clip (1) must be replaced.

17B-31
PETROL INJECTION
Injector rail - Injectors: Removal - Refitting
D4F, and 780 or 782
17B
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the dipstick.
aDisconnect:
-the oil vapour rebreathing pipe from the inlet dis-
tributor (9) ,
-the injector rail electrical wiring connector (10) ,
-the injector rail fuel supply pipe (11) .aRemove:
-the injector rail bolts (12) ,
-the « injector rail - injector » assembly by pulling it
gently.
aDisconnect the injector electrical wiring connectors.
aRemove the electrical wiring from the « injector rail -
injector » assembly.
aRemove:
-the clips (13) from the injectors,
-the injectors (14) .
122389
122388
WARNING
To avoid any corrosion or damage, protect the
areas on which fuel is likely to r un.
120955
101492