coolant level SAAB 9-2X 2006 Owners Manual

7-6
Starting and operating

A vehicle fails
the OBD inspection if the
“CHECK ENGINE” warning light/MIL is
not properly operating or there is one or
more diagnostic trouble codes stored in
vehicle’s computer with the “CHECK EN-
GINE” warning light/MIL illuminated.

A state emission inspection may reject
(not pass or fail) a vehicle if the number of
OBD system readiness monitors “Not
Ready” is greater than one. Under this
condition, the vehicle operator should be
instructed to drive his/her vehicle for a few
days to set the monitors and return for an
emission re-inspection.

Owners of rejected or failing vehicles
should contact their Saab Dealer for ser-
vice.
Preparing to driveYou should perform the following checks
and adjustments every day before you
start driving.
1. Check that all windows, mirrors, and
lights are clean and unobstructed.
2. Check the appearance and condition of
the tires. Also check tires for proper infla-
tion.
3. Look under the vehicle for any sign of
leaks.
4. Check that the hood, trunk and rear lift-
gate are fully closed.
5. Check the adjustment of the seat.
6. Check the adjustment of the inside and
outside mirrors.
7. Fasten your seatbelt. Check that your
passengers have fastened their seatbelts.
8. Check the operation of the warning and
indicator lights when the ignition switch is
turned to the “ON” position.
9. Check the gauges, indicator and warn-
ing lights after starting the engine.NOTEEngine oil, engine coolant, brake fluid,
washer fluid and other fluid levels
should be checked daily, weekly or at
fuel stops.
Starting the engine
Manual transmission vehicle1. Apply the parking brake.
2. Turn off unnecessary lights and acces-
sories.
3. Press the clutch pedal to the floor and
shift the shift lever into neutral. Hold the
clutch pedal to the floor while starting the
engine.
The starter motor will only operate when
the clutch pedal is pressed fully to the
floor.
4. Turn the ignition switch to the “ON” po-
sition and check the operation of the warn-
ing and indicator lights. Refer to the
“Warning and indicator lights” section
(chapter 3).
5. Turn the ignition switch to the “START”
position without depressing the accelera-
tor pedal. Release the key immediately af-
ter the engine has started.Do not operate the starter motor
continuously for more than ten sec-
onds. If the engine fails to start after
operating the starter for five to ten
seconds, wait for ten seconds or
more before trying again.
A1910BE-A-GSAAB.book Page 6 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

9-10
In case of emergency
Engine overheatingIf the engine overheats, safely pull off the
road and stop the vehicle in a safe place.
If steam is coming from the
engine compartmentTurn the engine off and get everyone
away from the vehicle until it cools down.
If no steam is coming from
the engine compartment1. Keep the engine running at idling
speed.
2. Open the hood to ventilate the engine
compartment.
Confirm that the cooling fan is turning. If
the fan is not turning, immediately turn offthe engine and contact your authorized
dealer for repair.
3. After the engine coolant temperature
has dropped, turn off the engine.
If the temperature gauge stays at the
overheated zone, turn off the engine.
4. After the engine has fully cooled down,
check the coolant level in the reserve
tank.
If the coolant level is below the “LOW”
mark, add coolant up to the “FULL” mark.
5. If there is no coolant in the reserve
tank, add coolant to the reserve tank.
Then remove the radiator cap and fill the
radiator with coolant.
If you remove the radiator cap from a hot
radiator, first wrap a thick cloth around the
radiator cap, then turn the cap counter-
clockwise slowly without pressing down
until it stops. Release the pressure from
the radiator. After the pressure has been
fully released, remove the cap by pressing
down and turning it.
TowingIf towing is necessary, it is best done by
your Saab dealer or a commercial towing
service. Observe the following procedures
for safety.
Never attempt to remove the radia-
tor cap until the engine has been
shut off and has fully cooled down.
When the engine is hot, the coolant
is under pressure. Removing the
cap while the engine is still hot
could release a spray of boiling hot
coolant, which could burn you very
seriously.
Never tow AWD vehicles (both AT
and MT) with the front wheels raised
off the ground while the rear wheels
are on the ground, or with the rear
wheels raised off the ground while
the front wheels are on the ground.
This will cause the vehicle to spin
away due to the operation or deteri-
oration of the center differential.
900282
A1910BE-A-GSAAB.book Page 10 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

111
Maintenance and service
Maintenance schedule ....................................... 11-3
Maintenance precautions .................................. 11-3
Before checking or servicing in the engine
compartment ........................................................ 11-4
When you do checking or servicing in the engine
compartment while the engine is running ......... 11-4
Engine hood ....................................................... 11-4
Engine compartment overview ......................... 11-6
Non-turbo models ................................................... 11-6
Turbo models .......................................................... 11-7
Engine oil ............................................................ 11-8
Checking the oil level ............................................. 11-8
Changing the oil and oil filter ................................ 11-8
Recommended grade and viscosity ..................... 11-11
Recommended grade and viscosity under severe
driving conditions ................................................ 11-11
Synthetic oil ............................................................ 11-12
Cooling system .................................................. 11-12
Cooling fan, hose and connections ...................... 11-12
Engine coolant ........................................................ 11-13
Air cleaner element ............................................ 11-15
Replacing the air cleaner element ......................... 11-16
Spark plugs ......................................................... 11-18
Recommended spark plugs ................................... 11-18
Drive belts ........................................................... 11-18
Manual transmission oil .................................... 11-19
Checking the oil level ............................................. 11-19
Recommended grade and viscosity ..................... 11-20
Automatic transmission fluid ............................ 11-20
Checking the fluid level .......................................... 11-20
Recommended fluid ............................................... 11-21
Front differential gear oil (AT vehicles) ............ 11-22
Checking the oil level ............................................. 11-22
Recommended grade and viscosity ..................... 11-22
Rear differential gear oil .................................... 11-23
Checking the gear oil level .................................... 11-23
Recommended grade and viscosity ..................... 11-23
Power steering fluid ........................................... 11-24
Checking the fluid level .......................................... 11-24
Recommended fluid ............................................... 11-25
Brake fluid ........................................................... 11-25
Checking the fluid level .......................................... 11-25
Recommended brake fluid ..................................... 11-26
Clutch fluid (MT vehicles) .................................. 11-26
Checking the fluid level .......................................... 11-26
Recommended clutch fluid .................................... 11-27
Brake booster ..................................................... 11-27
Brake pedal ......................................................... 11-27
Checking the brake pedal free play ...................... 11-27
Checking the brake pedal reserve distance ......... 11-28
Clutch pedal (MT vehicles) ................................ 11-28
Checking the clutch function ................................ 11-28
Checking the clutch pedal free play ..................... 11-28
Replacement of brake pad and lining ............... 11-29
Breaking-in of new brake pads and linings .......... 11-29
Parking brake stroke .......................................... 11-30
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

11 - 6
Maintenance and service
Engine compartment overview
Non-turbo models
12 3456
7 8 9 10 11
1312
B00464
1) Air cleaner element (page 11-15)
2) Manual transmission oil level gauge
(MT) (page 11-19) or Differential gear
oil level gauge (AT) (page 11-22)
3) Clutch fluid reservoir (page 11-26)
4) Automatic transmission fluid level
gauge (page 11-20)
5) Brake fluid reservoir (page 11-25)
6) Fuse box (page 11-40)
7) Battery (page 11-39)
8) Windshield washer tank (page 11-35)
9) Engine coolant reservoir
(page 11-13)
10) Engine coolant reservoir
oil level gauge (page 11-8)
11) Engine oil level gauge filler cap
(page 11-8)
12) Radiator cap (page 11-13)
13) Power steering fluid reservoir
(page 11-24)
A1910BE-A-GSAAB.book Page 6 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Maintenance and service
11 - 7
– CONTINUED –
11
Turbo models
12 3456
7 8 9 10 11 12 13
B00466
1) Air cleaner element (page 11-15)
2) Manual transmission oil level gauge
(MT) (page 11-19) or Differential gear
oil level gauge (AT) (page 11-22)
3) Automatic transmission fluid level
gauge (page 11-20)
4) Clutch fluid reservoir (page 11-26)
5) Brake fluid reservoir (page 11-25)
6) Fuse box (page 11-40)
7) Battery (page 11-39)
8) Windshield washer tank (page 11-35)
9) Engine oil filler cap (page 11-8)
10) Engine coolant reservoir
(page 11-13)
11) Engine oil level gauge (page 11-8)
12) Radiator cap (page 11-13)
13) Power steering fluid reservoir
(page 11-24)
A1910BE-A-GSAAB.book Page 7 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Maintenance and service
11 - 1 3
11
– CONTINUED –

Engine coolant
Checking the coolant level1) “FULL” level mark
2) “LOW” level markCheck the coolant level at each fuel stop.
1. Check the coolant level on the outside
of the reservoir while the engine is cool.
2. If the level is close to or lower than the
“LOW” level mark, add coolant up to the
“FULL” level mark. If the reserve tank is
empty, remove the radiator cap and refill
as required.3. After refilling the reserve tank and the
radiator, reinstall the caps and check that
the rubber gaskets inside the radiator cap
are in the proper position.

Changing the coolant
Always add genuine cooling system con-
ditioner whenever the coolant is replaced.
Change the engine coolant and add gen-
uine cooling system conditioner using the
following procedures according to the
maintenance schedule.
1. Remove the under cover.
2. Place a proper container under the
drain plug and loosen the drain plug.
3. Loosen the radiator cap to drain the
coolant from the radiator. Then drain the
coolant from the reserve tank. Tighten the
drain plug securely.NOTE (Turbo model only)The cap (without tabs) on top of the ra-
diator does not need to be removed. To
add coolant, remove the cap (with tabs)
FULL
LOW
1
2
B00468

Be careful not to spill engine cool-
ant when adding it. If coolant
touches the exhaust pipe, it may
cause a bad smell, smoke, and/or
a fire.
If engine coolant gets on the
exhaust pipe, be sure to wipe it
off.

Do not splash the engine coolant
over painted parts. The alcohol
contained in the engine coolant
may damage the paint surface.
B00018
B00019
A1910BE-A-GSAAB.book Page 13 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

11 - 1 4
Maintenance and service
on the coolant tank on top of the en-
gine.4. Install the under cover.Non-turbo models
1) Filler neck
2) Fill up to this levelTurbo models
1) Filler neck
2) Fill up to this level
5. Slowly pour the coolant and fill up to
just below the filler neck, allowing enough
room to add genuine cooling system con-
ditioner in the radiator. Add genuine cool-
ing system conditioner until the coolant
level reaches the filler neck. Do not pour
the coolant too quickly, as this may lead to
insufficient air bleeding and trapped air in
the system.
Guideline of coolant quantity (including cool-
ant in reservoir tank):
Non-turbo models:
MT. 7.4 US qt (7.0 liters, 6.2 Imp qt)
AT. 7.3 US qt (6.9 liters, 6.1 Imp qt)
Turbo models:
MT. 8.1 US qt (7.7 liters, 6.8 Imp qt)
AT. 8.0 US qt (7.6 liters, 6.7 Imp qt)
1) “FULL” level mark
2) “LOW” level mark
Never attempt to remove the radia-
tor cap until the engine has been
shut off and has cooled down com-
pletely. Since the coolant is under
pressure, you may suffer serious
burns from a spray of boiling hot
coolant when the cap is removed.
1
2
B00453
1
2
B00454
FULL
LOW
1
2
B00468
A1910BE-A-GSAAB.book Page 14 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

Maintenance and service
11 - 1 5
11
– CONTINUED –
6. Pour the coolant and fill to the reservoir
tank’s “FULL” level mark.
7. Put the radiator cap back on and tight-
en firmly. At this time, make sure that therubber gasket in the radiator cap is cor-
rectly in place.
8. Start and run the engine for more than
five minutes at 2,000 to 3,000 rpm.
9. Stop the engine and wait until the cool-
ant cools down (122 to 140
F [50 to
60
C]). If there is any loss of coolant, add
coolant to the radiator’s filler neck and to
the reserve tank’s “FULL” level.
10.Put the radiator cap and reservoir cap
back on and tighten firmly.
Air cleaner elementThe air cleaner element functions as a fil-
ter screen. When the element is perforat-
ed or removed, engine wear will be exces-
sive and engine life shortened.
The air cleaner element is a viscous type.
It is unnecessary to clean or wash the ele-
ment.

Be careful not to spill engine cool-
ant when adding it. If coolant
touches the exhaust pipe, it may
cause a bad smell, smoke, and/or
a fire. If engine coolant gets on the
exhaust pipe, be sure to wipe it
off.

Do not splash the engine coolant
over painted parts. The alcohol
contained in the engine coolant
may damage the paint surface.
B00018
Do not operate the engine with the
air cleaner element removed. The air
cleaner element not only filters in-
take air but also stops flames if the
engine backfires. If the air cleaner
element is not installed when the en-
gine backfires, you could be burned.
A1910BE-A-GSAAB.book Page 15 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

11 - 3 6
Maintenance and service
Washer fluid level gaugeRemove the washer tank filler cap, then
check the fluid level indicated by the level
gauge (attached to the inside of the cap).
If the level is near the “Low” mark, add flu-id until it reaches the “Hi” level on the level
gauge or the “Full” mark on the tank.
Use windshield washer fluid. If windshield
washer fluid is unavailable use clean wa-
ter.
In areas where water freezes in winter,
use an anti-freeze type windshield washer
fluid.
If you fill the reservoir tank with a fluid with
a different concentration from the one
used previously, purge the old fluid from
the piping between the reservoir tank and
washer nozzles by operating the washer
for a certain period of time. Otherwise, if
the concentration of the fluid remaining in
the piping is too low for the outside tem-
perature, it may freeze and block the noz-
zles.
Replacement of wiper bladesGrease, wax, insects, or other material on
the windshield or the wiper blade results in
jerky wiper operation and streaking on the
glass. If you cannot remove the streaks af-
ter operating the windshield washer or if
the wiper operation is jerky, clean the out-
er surface of the windshield (or rear win-
dow) and the wiper blades using a sponge
or soft cloth with a neutral detergent or
mild-abrasive cleaner. After cleaning,
rinse the windshield and wiper blades with
clean water. The windshield is clean if
beads do not form when you rinse the
windshield with water.If you cannot eliminate the streaking even
after following this method, replace the
wiper blades using the following proce-
dures:
Windshield wiper blades as-
sembly1. Raise the wiper arm off the windshield.
Hi
Low
300172
FULL
300524

Adjust the washer fluid concen-
tration appropriately for the out-
side temperature. If the concen-
tration is inappropriate, sprayed
washer fluid may freeze on the
windshield and obstruct your
view, and the fluid may freeze in
the reservoir tank.

Never use engine coolant as
washer fluid because it could
cause paint damage.
Do not clean the wiper blades with
gasoline or a solvent, such as paint
thinner or benzene. This will cause
deterioration of the wiper blades.
A1910BE-A-GSAAB.book Page 36 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com

14-4
Index
Electronic Brake Force Distribution (EBD) system ........... 7-18
Emergency Locking Retractor (ELR) ................................ 1-10
Engine
Compartment overview ................................................. 11-6
Coolant ....................................................................... 11-13
Exhaust gas (Carbon monoxide) ............................... 6, 8-2
Hood ............................................................................. 11-4
Oil ................................................................................. 11-8
Overheating ................................................................. 9-10
Starting .......................................................................... 7-6
Stopping ........................................................................ 7-8
Exterior care ..................................................................... 10-2
F
Flat tires ............................................................................. 9-4
Floor mat ............................................................................ 6-8
Fluid level
Automatic transmission .............................................. 11-20
Brake .......................................................................... 11-25
Clutch ......................................................................... 11-26
Power steering ............................................................ 11-24
Folding down the rear seat ................................................. 1-7
Front
Differential gear oil ...................................................... 11-22
Fog light button ............................................................ 3-19
Seatbelt pretensioners ................................................. 1-19
Seats ............................................................................. 1-2
Turn signal light .......................................................... 11-49
Fuel .................................................................................... 7-2
Economy hints ............................................................... 8-2
Filler lid and cap ............................................................ 7-3
Gauge ............................................................................ 3-7
Requirements ................................................................ 7-2Fuses .............................................................................. 11-41
Fuses and circuits ............................................................. 12-6
G
GAWR (Gross Axle Weight Rating) .................................. 8-11
Glove box ........................................................................... 6-4
GVWR (Gross Vehicle Weight Rating) ............................. 8-11
H
Hazard warning flasher ....................................................... 3-6
Head restraint adjustment ........................................... 1-4, 1-6
Headlight beam leveler ..................................................... 3-18
Headlight flasher ............................................................... 3-16
Headlights .............................................................. 3-16, 11-46
Heater operation ................................................................. 4-5
High beam indicator light .................................................. 3-14
Horn .................................................................................. 3-26
Hose and connections .................................................... 11-12
I
Ignition switch ..................................................................... 3-3
Illuminated entry ................................................................. 2-8
Illumination brightness control .......................................... 3-18
Immobilizer ......................................................................... 2-3
Indicator light
High beam ................................................................... 3-14
Selector lever position ................................................. 3-14
Turn signal ................................................................... 3-14
Inside mirror ...................................................................... 3-24
Interior light ......................................................................... 6-2A1910BE-A-GSAAB.book Page 4 Tuesday, September 6, 2005 8:37 AM
ProCarManuals.com