SATURN ASTRA 2008 Owners Manual

Windshield Wiper Blade
Replacement
Front Windshield Wiper
Windshield wiper blades should be
inspected for wear or cracking.
See “Maintenance Replacement
Parts” in the Limited Warranty,
Maintenance and owner Assistance
Information manual for the proper
type and length.
Raise the wiper arm, tilt the wiper
blade at a 90° angle to the
wiper arm, and remove to the side.
1. Turn the ignition off.
2. With the key in the ignition and
key in the LOCK position, press
the wiper lever down. Release
the wiper lever when the wipers
are in the vertical position.3. Raise the wiper arm away from
the windshield.
4. Turn the wiper blade at a 90°
angle to the wiper arm and
remove the blade to the side.
5. Install the new wiper blade.
6. Lower the wiper arm on to the
windshield.
Rear Windshield Wiper
1. Lift the wiper arm straight up.
2. Push the wiper blade straight out
of the wiper arm to remove.
3. Install the new wiper blade.
Vehicle Service and Care 9-21
ProCarManuals.com

Brakes
Brake Fluid
The brake master cylinder and, on
manual transmission vehicles,
the clutch hydraulic system use the
same reservoir. The reservoir is
lled with DOT-4 brake uid.
SeeEngine Compartment Overview
on page 9-6for the location of
the reservoir.
There are only two reasons why the
brake uid level in the reservoir
might go down. The rst is that the
brake uid goes down to an
acceptable level during normal
brake lining wear. When new linings
are put in, the uid level goes
back up. The other reason is that
uid is leaking out of the brake
or clutch hydraulic system. If it is,have the brake or clutch hydraulic
system xed, since a leak means
that sooner or later the brakes
or clutch will not work well.
It is not a good idea to top off the
brake uid. Adding brake uid
will not correct a leak. If uid is
added when the linings are worn,
there will be too much uid
when new brake linings are
installed. Add or remove brake uid,
as necessary, only when work is
done on the brake or clutch
hydraulic system.
{CAUTION
If your vehicle has too much
brake uid, it can spill on the
engine. The uid will burn if the
engine is hot enough. You or
others could be burned, and
your vehicle could be damaged.
Add brake uid only when work
is done on the brake and/or
clutch hydraulic system.Refer to “Scheduled Maintenance”
in the Limited Warranty,
Maintenance and Owner Assistance
Information manual to determine
when to check the brake uid.
Checking Brake Fluid
The brake uid can be checked
without taking off the cap by looking
at the brake uid reservoir.
The uid level should be above
MIN. If it is not, have your brake
hydraulic system checked to see
if there is a leak. After work is done
on the brake hydraulic system,
make sure the level is above the
MIN but not over the MAX mark.
What to Add
When you do need brake uid,
use only DOT-4 brake uid.
It is recommended that you ush
the brake hydraulic system and
rell it with new DOT-4 uid
at a regular maintenance service
every two years. See “Additional
9-22 Vehicle Service and Care
ProCarManuals.com

Required Services” in the Limited
Warranty, Maintenance and
Owner Assistance Information
manual. Use new brake uid
from a sealed container only.
See “Recommended Fluids and
Lubricants” in the Limited Warranty,
Maintenance and Owner Assistance
Information manual.
Always clean the brake uid
reservoir cap and the area
around the cap before removing it.
This helps keep dirt from entering
the reservoir.
{CAUTION
With the wrong kind of uid in
the brake hydraulic system,
the brakes might not work well.
This could cause a crash.
Always use the proper brake
uid.Notice:
Using the wrong uid can
badly damage brake
hydraulic system parts.
For example, just a few drops
of mineral-based oil, such
as engine oil, in the brake
hydraulic system can
damage brake hydraulic
system parts so badly that
they will have to be replaced.
Do not let someone put in
the wrong kind of uid.
If you spill brake uid on your
vehicle’s painted surfaces, the
paint nish can be damaged.
Be careful not to spill brake
uid on your vehicle. If you
do, wash it off immediately.
SeeExterior Cleaning on
page 9-75.
Brake Wear
Your vehicle has disc brakes.
Notice:Continuing to drive
with worn-out brake pads could
result in costly brake repair.
Front disc brake pads have built-in
brake pad wear indicators that
make a high-pitched warning sound
when the brake pads are worn
and new pads are needed.
The sound can come and go or be
heard all the time your vehicle is
moving, except when you are
pushing on the brake pedal rmly.
{CAUTION
The brake wear warning sound
means that soon the brakes will
not work well. That could lead
to an accident. When you hear
the brake wear warning sound,
have your vehicle serviced.
Vehicle Service and Care 9-23
ProCarManuals.com

Rear disc brake pads do not have
built-in brake pad wear indicators.
Periodic visual inspection of the rear
brake pads is required to determine
when to replace the pads. Visually
inspect the rear brake pads
whenever the rear wheels are
removed such as during tire rotation.
1. Set the parking brake and make
sure that the brakes have been
given enough time to cool.
2. Remove the rear wheels.
3. Visually inspect the rear brake
inner pads (C) at each rear
wheel through the inspection
window in the brake caliper (A).Brake pads should be replaced
when the inner pad (C) is
worn to 5/64 in (2 mm) of pad
thickness (B). New brake
pads, with no wear, are 25/64 of
an inch (10 mm) thick.
4. After brake pad inspection or
replacement, install the rear
wheels.Some driving conditions or climates
can cause a brake squeal when
the brakes are rst applied or lightly
applied. This does not mean
something is wrong with the brakes.
Properly torqued wheel bolts are
necessary to help prevent brake
pulsation. When tires are rotated,
inspect brake pads for wear and
evenly tighten wheel bolts in
the proper sequence to torque
specications inCapacities
and Specifications on page 10-2.
Brake linings should always
be replaced as complete axle sets.
Brake Pedal Travel
See your dealer/retailer if the brake
pedal does not return to normal
height, or if there is a rapid increase
in pedal travel. This could be a sign
that brake service might be required.
Brake Adjustment
Every time you make a brake stop,
the disc brakes adjust for wear.
9-24 Vehicle Service and Care
ProCarManuals.com

Replacing Brake System Parts
The braking system on a vehicle
is complex. Its many parts have to
be of top quality and work well
together if the vehicle is to have
really good braking. Your vehicle
was designed and tested with
top-quality brake parts. When you
replace parts of the braking
system — for example, when the
brake linings wear down and
you need new ones put in — be
sure you get new approved
replacement parts. If you do not,
the brakes might not work properly.
For example, if someone puts in
brake linings that are wrong for
your vehicle, the balance between
the front and rear brakes can
change — for the worse. The
braking performance you have
come to expect can change in many
other ways if someone puts in the
wrong replacement brake parts.
Battery
Your vehicle has a maintenance
free battery. When it is time
for a new battery, see your
dealer/retailer for one that has the
replacement number shown on
the original battery’s label.
SeeEngine Compartment Overview
on page 9-6for battery location.
Warning:Battery posts, terminals,
and related accessories contain
lead and lead compounds,
chemicals known to the State of
California to cause cancer and
reproductive harm. Wash hands
after handling.
Vehicle Storage
{CAUTION
Batteries have acid that can
burn you and gas that can
explode. You can be badly hurt
if you are not careful. SeeJump
Starting on page 9-68for tips
on working around a battery
without getting hurt.
Infrequent Usage: If you drive your
vehicle infrequently, remove the
black, negative (−) cable from
the battery. This will help keep the
battery from running down.
Extended Storage: For extended
storage of your vehicle, remove the
black, negative (−) cable from
the battery or use a battery trickle
charger. This will help maintain
the charge of the battery over an
extended period of time.
Vehicle Service and Care 9-25
ProCarManuals.com

Headlamp Aiming
The optical headlamp aiming system
has been preset at the factory
and should need no further
adjustment.
However, If the vehicle is damaged
in a crash, the headlamp aim
may be affected and adjustment
may be necessary.
If oncoming vehicles ash their high
beams at you, this may also mean
the vertical aim needs to be adjusted.
It is recommended that the vehicle
is taken to your dealer/retailer for
service if the headlamps need to be
re-aimed. It is possible however, to
re-aim the headlamps as described.The vehicle should:Be placed so the headlamps
are 25 ft. (7.6 m) from a light
colored wall.
Have all four tires on a perfectly
level surface which is level all
the way to the wall.
Be placed so it is perpendicular
to the wall.
Not have any snow, ice, or
mudonit.
Be fully assembled and all other
work stopped while headlamp
aiming is being done.
Have a full tank of fuel and
one person or 160 lbs (75 kg)
on the driver seat.
Have all tires properly inated.Headlamp aiming is done with the
vehicle’s low-beam headlamps.
The high-beam headlamps will be
correctly aimed if the low-beam
headlamps are aimed properly.
To adjust the vertical aim on
the headlamps:
1. Open the hood. SeeHood
Release on page 9-5for more
information.
2. Locate the aim dot on the lens of
the low-beam headlamp.
9-26 Vehicle Service and Care
ProCarManuals.com

3. Record the distance from the
ground to the aim dot on the
low-beam headlamp.
4. At a wall, measure from the
ground upward (A) to the
recorded distance from Step 3
and mark it.
5. Draw or tape a horizontal line (B)
on the wall the width of the
vehicle at the height of the
mark in Step 4.Notice:Do not cover a headlamp
to improve beam cut-off when
aiming. Covering a headlamp may
cause excessive heat build-up
which may cause damage to the
headlamp.
6. Turn on the low-beam headlamps
and place a piece of cardboard
or equivalent in front of the
headlamp not being adjusted.
Do not place it directly on
the headlamp. This allows only
the beam of light from the
headlamp being adjusted to
be seen on the at surface.7. Locate the vertical headlamp
aiming screws, which are under
the hood near each headlamp
assembly.
The adjustment screw can be
turned with a 6 mm socket
wrench.
8. Turn the vertical aiming screw
until the headlamp beam is aimed
to the horizontal tape line. Turn it
clockwise or counterclockwise
to raise or lower the angle of
the beam.
Vehicle Service and Care 9-27
ProCarManuals.com

9. Make sure that the light from the
headlamp is positioned at the
bottom edge of the horizontal
tape line. The lamp on the left (A)
shows the correct headlamp aim.
The lamp on the right (B) shows
the incorrect headlamp aim.
10. Repeat Steps 7 through 9 for
the opposite headlamp.
Bulb Replacement
For the proper type of replacement
bulbs, seeReplacement Bulbs
on page 9-33.
For any bulb changing procedure
not listed in this section, contact
your dealer/retailer.
Halogen Bulbs
{CAUTION
Halogen bulbs have
pressurized gas inside and can
burst if you drop or scratch the
bulb. You or others could be
injured. Be sure to read and
follow the instructions on the
bulb package.
Front Turn Signal Lamps
1. The bulbs of the turn signal lamp
are replaced through openings in
the front wheel wells. Turn the
wheel to gain access to the push
tabs and remove the cover.
9-28 Vehicle Service and Care
ProCarManuals.com

2. Turn the bulb socket
counterclockwise and pull
straight out.
3. Turn bulb counterclockwise
and remove.
4. Install new bulb.
5. Reverse Steps 2 through 4 to
reinstall.
Taillamps
(Five-Door Hatchback)
A. Backup Lamp
B. Taillamp
C. Taillamp/Stoplamp/Turn
Signal LampTo replace one of these bulbs:
1. Open the liftgate.
2. To replace the bulbs on the
driver side, turn both locks
and remove the cover.
To replace the bulbs on the
passenger side, turn the lock
clockwise and remove the cover.
3. Detach the plug connector
from the bulb assembly.
Vehicle Service and Care 9-29
ProCarManuals.com

4. Turn the nuts counterclockwise
and hold the outside of taillamp
assembly.
5. Pull the taillamp assembly
straight out.
6. Remove the three nuts.
7. Press on the tabs on the outside
of bulb assembly and remove the
bulb assembly.
8. Remove the bulb from the bulb
assembly.9. Install a new bulb without
touching the glass.
10. Reinstall the bulb assembly in
taillamp assembly.
11. Make sure the seals are applied
to the taillamp assembly and
screws.
12. Insert the taillamp assembly
into the body.
13. Reinstall the three nuts.
14. Attach the plug connector to the
bulb assembly.
Taillamps
(Three-Door Hatchback)
A. Backup Lamp
B. Taillamp
C. Taillamp/Stoplamp/Turn
Signal Lamp
9-30 Vehicle Service and Care
ProCarManuals.com