check oil SATURN ASTRA 2009 User Guide

Page 197 of 314

{CAUTION
An electric engine cooling fan
under the hood can start up even
when the engine is not running and
can cause injury. Keep hands,
clothing, and tools away from any
underhood electric fan.
If the coolant inside the coolant
reservoir is boiling, do not do
anything else until it cools down.
The vehicle should be parked on a
level surface.
The coolant level should be at or
above the KALT/COLD mark on the
coolant reservoir. If it is not, you
may have a leak at the coolant
reservoir pressure cap or in the
radiator hoses, heater hoses,
radiator, water pump, or somewhere
else in the cooling system.
{CAUTION
Heater and radiator hoses, and
other engine parts, can be very
hot. Do not touch them. If you do,
you can be burned.
Do not run the engine if there is a
leak. If you run the engine, it
could lose all coolant. That could
cause an engine re, and you
could be burned. Get any leak
xed before you drive the vehicle.
If there seems to be no leak,
with the engine on, check to see
if the electric engine cooling fans are
running. If the engine is overheating,
both fans should be running.
If they are not, your vehicle needs
service.Notice:Engine damage from
running the engine without
coolant is not covered by the
warranty.
Notice:Using coolant other
than DEX-COOL
®can cause
premature engine, heater core, or
radiator corrosion. In addition,
the engine coolant could require
changing sooner, at 30,000 miles
(50 000 km) or 24 months,
whichever occurs rst.
Any repairs would not be
covered by the vehicle warranty.
Always use DEX-COOL
®
(silicate-free) coolant in the
vehicle.
Vehicle Service and Care 9-13
ProCarManuals.com

Page 198 of 314

How to Add Coolant to the
Coolant Reservoir
Notice:This vehicle has a
specic coolant ll procedure.
Failure to follow this procedure
could cause the engine to
overheat and be severely
damaged.
If you have not found a problem yet,
check to see if coolant is visible
in the coolant reservoir. If coolant is
visible but the coolant level is not
at or above the KALT/COLD mark,
add a 50/50 mixture of clean,
drinkable water and DEX-COOL
®
coolant at the coolant reservoir,
but be sure the cooling system,
including the coolant reservoir
pressure cap, is cool before you
do it. SeeEngine Coolant on
page 9-16for more information.If no coolant is visible in the coolant
reservoir, add coolant as follows:
{CAUTION
Steam and scalding liquids from a
hot cooling system can blow out
and burn you badly. They are
under pressure, and if you turn
the coolant reservoir pressure
cap — even a little — they can
come out at high speed. Never
turn the cap when the cooling
system, including the coolant
reservoir pressure cap, is hot.
Wait for the cooling system and
coolant reservoir pressure cap to
cool if you ever have to turn the
pressure cap.
{CAUTION
Adding only plain water to the
cooling system can be dangerous.
Plain water, or some other liquid
such as alcohol, can boil before
the proper coolant mixture will.
The vehicle’s coolant warning
system is set for the proper
coolant mixture. With plain water
or the wrong mixture, the engine
could get too hot but you would
not get the overheat warning.
The engine could catch re and
you or others could be burned.
Use a 50/50 mixture of clean,
drinkable water and DEX-COOL
®
coolant.
Notice:In cold weather, water
can freeze and crack the engine,
radiator, heater core and other
parts. Use the recommended
coolant and the proper coolant
mixture.
9-14 Vehicle Service and Care
ProCarManuals.com

Page 261 of 314

If your vehicle has a basecoat/
clearcoat paint nish, the clearcoat
gives more depth and gloss to
the colored basecoat. Always use
waxes and polishes that are
non-abrasive and made for a
basecoat/clearcoat paint nish.
Notice:Machine compounding
or aggressive polishing on a
basecoat/clearcoat paint nish
may damage it. Use only
non-abrasive waxes and
polishes that are made for a
basecoat/clearcoat paint nish
on the vehicle.
Foreign materials such as calcium
chloride and other salts, ice
melting agents, road oil and tar,
tree sap, bird droppings, chemicals
from industrial chimneys, etc.,
can damage your vehicle’s nish if
they remain on painted surfaces.
Wash the vehicle as soon as
possible. If necessary, use
non-abrasive cleaners that are
marked safe for painted surfaces to
remove foreign matter.Exterior painted surfaces are
subject to aging, weather and
chemical fallout that can take
their toll over a period of years.
You can help to keep the paint nish
looking new by keeping your
vehicle garaged or covered
whenever possible.
Protecting Exterior Bright
Metal Parts
Bright metal parts should be
cleaned regularly to keep their
luster. Wash with water or
use chrome polish on chrome or
stainless steel trim, if necessary.
Use special care with aluminum trim.
To avoid damaging protective trim,
never use auto or chrome polish,
steam or caustic soap to clean
aluminum. A coating of wax, rubbed
to high polish, is recommended for
all bright metal parts.Washing Your Vehicle
The best way to preserve your
vehicle’s nish is to keep it clean by
washing it often.
Do not wash the vehicle in direct
sunlight. Use a car washing soap.
Notice:Certain cleaners contain
chemicals that can damage the
emblems or nameplates on the
vehicle. Check the cleaning
product label. If it states that it
should not be used on plastic
parts, do not use it on the vehicle
or damage may occur and it would
not be covered by the warranty.
Do not use cleaning agents that are
petroleum based or that contain
acid or abrasives, as they can
damage the paint, metal or plastic
on your vehicle. Approved cleaning
products can be obtained from
your dealer/retailer. Follow all
manufacturers’ directions regarding
correct product usage, necessary
safety precautions and appropriate
disposal of any vehicle care product.
Vehicle Service and Care 9-77
ProCarManuals.com

Page 269 of 314

Service and
Maintenance
Service and Maintenance
Introduction.......................11-1
Maintenance
Requirements..................11-1
Your Vehicle and the
Environment....................11-2
Using the Maintenance
Schedule.........................11-2
Scheduled Maintenance. . . .11-3
Additional Required
Services..........................11-6
Maintenance Footnotes.....11-8
Owner Checks and
Services..........................11-9
At Each Fuel Fill...............11-9
At Least Once a Month. . .11-10
At Least Once a Year.....11-10
Recommended Fluids
and Lubricants...............11-12
Maintenance
Replacement Parts........11-14
Engine Drive Belt
Routing..........................11-15
Maintenance Record........11-16
Service and
Maintenance
Introduction
Important: Keep engine oil at
the proper level and change as
recommended.
Maintenance
Requirements
Notice:Maintenance intervals,
checks, inspections, replacement
parts, and recommended uids
and lubricants as prescribed
in this manual are necessary to
keep this vehicle in good working
condition. Any damage caused
by failure to follow scheduled
maintenance might not be
covered by the vehicle warranty.
Service and Maintenance 11-1
ProCarManuals.com

Page 271 of 314

{CAUTION
Performing maintenance work on
a vehicle can be dangerous.
In trying to do some jobs, you can
be seriously injured. Do your own
maintenance work only if you
have the required know-how and
the proper tools and equipment
for the job. If you have any doubt,
see your dealer/retailer to have a
qualied technician do the work.
SeeDoing Your Own Service
Work on page 9-4.
Some maintenance services can be
complex. So, unless you are
technically qualied and have the
necessary equipment, have
your dealer/retailer do these jobs.
When you go to your dealer/retailer
for service, trained and supported
service technicians will perform
the work using genuine parts.To purchase service information,
seeService Publications Ordering
Information on page 12-15.
Owner Checks and Services on
page 11-9tells what should
be checked, when to check it, and
what can easily be done to help
keep the vehicle in good condition.
The proper replacement parts,
uids, and lubricants to use
are listed inRecommended Fluids
and Lubricants on page 11-12
andMaintenance Replacement
Parts on page 11-14. When
the vehicle is serviced, make sure
these are used. All parts should
be replaced and all necessary
repairs done before you or anyone
else drives the vehicle. We
recommend the use of genuine
parts from your dealer/retailer.
Scheduled Maintenance
When the letters InSP appear in
the odometer display, service
is required for the vehicle. Have the
vehicle serviced as soon as
possible within the mileage indicated
on the display. The engine oil and
lter must be changed at least once
a year and at this time the system
must be reset. Your dealer/retailer
has trained service technicians
who will perform this work using
genuine parts and reset the system.
If the engine oil life system is
ever reset accidentally, service
the vehicle within 3,000 miles
(5 000 km) since the last service.
Remember to reset the oil life
system whenever the oil is changed.
SeeEngine Oil Life System on
page 9-9for information on the oil
life system and resetting the system.
Service and Maintenance 11-3
ProCarManuals.com

Page 272 of 314

When InSP appears, certain
services, checks, and inspections
are required. Required services
are described in the following
for “MaintenanceI” and
“Maintenance II.” Generally, it is
recommended that the rst service
be Maintenance I, the second
service be Maintenance II, and then
alternate Maintenance Iand Maintenance
IIthereafter. However,
in some cases, Maintenance II
might be required more often.
Maintenance I—Use
Maintenance Iif InSP displays
within 10 months since the vehicle
was purchased or Maintenance II
was performed. Maintenance
II—Use
Maintenance IIif the previous
service performed was
Maintenance I. Always use
Maintenance IIwhenever the letters
InSP display 10 months or more
since the last service or if InSP has
not come on at all for one year.
Scheduled Maintenance
Service MaintenanceIMaintenance II
Change engine oil and lter. See Engine Oil on page 9-7. Reset oil life system.
See Engine Oil Life System on page 9-9 .An Emission Control Service. ••
Visually check for any leaks or damage. See footnote (a). ••
Inspect engine air cleaner lter. If necessary, replace lter. See Engine Air
Cleaner/Filter on page 9-11 .See footnote (b). •
Rotate tires and check ination pressures and wear. See Tire Inspection and
Rotation on page 9-52 and “Tire Wear Inspection” in At Least Once a Month
on page 11-10. ••
11-4 Service and Maintenance
ProCarManuals.com

Page 276 of 314

Maintenance Footnotes
(a)A fluid loss in any vehicle system
could indicate a problem. Have the
system inspected and repaired
and the fluid level checked. Add fluid
if needed.
(b)If driving regularly under dusty
conditions or in high-polluted
regions, replace the filter at each
engine oil change.
(c)Inspect brake lines and hoses for
proper hook-up, binding, leaks,
cracks, chafing, etc. Inspect disc
brake pads for wear and rotors for
surface condition. Inspect other
brake parts, including calipers,
parking brake, etc.
(d)Inspect front and rear suspension
and steering system for damaged,
loose, or missing parts or signs of
wear. Inspect power steering cables
for proper hook-up, binding, cracks,
chafing, etc. Inspect power steering
hydraulic lines and hoses for proper
hook-up, binding, leaks, cracks,
chafing, etc.(e)Inspect hoses and have them
replaced if they are cracked,
swollen, or deteriorated. Inspect all
pipes, fittings and clamps; replace
with genuine parts as needed.
To help ensure proper operation,
a pressure test of the cooling system
and pressure cap and cleaning
the outside of the radiator and
air conditioning condenser is
recommended at least once a year.
(f)Inspect wiper blades for wear,
cracking, or contamination.
Clean the windshield and wiper
blades, if contaminated. Replace
wiper blades that are worn or
damaged. See Windshield Wiper
Blade Replacement on page 9-21
and “Windshield and Wiper Blades”
in Exterior Cleaning on page 9-76.
(g)Make sure the safety belt
reminder light and safety belt
assemblies are working properly.
Look for any other loose or
damaged safety belt system parts.
If you see anything that might keep
a safety belt system from doingits job, have it repaired. Have any
torn or frayed safety belts replaced.
Also see Airbag System Check
on page 1-37.
(h)Lubricate all key lock cylinders,
door hinges and latches, hood
hinges and latches, and trunk lid
hinges and latches. More frequent
lubrication may be required
when exposed to a corrosive
environment. Applying silicone
grease on weatherstrips with a clean
cloth will make them last longer,
seal better, and not stick or squeak.
(i)Change automatic transmission
fluid if the vehicle is mainly driven
under one or more of these
conditions:
In heavy city traffic where the
outside temperature regularly
reaches 90°F (32°C) or higher.
In hilly or mountainous terrain.
When doing frequent trailer
towing.
Uses such as found in taxi, police,
or delivery service.
11-8 Service and Maintenance
ProCarManuals.com

Page 277 of 314

(j)Drain, flush, and refill cooling
system. This service can be
complex; you should have your
dealer/retailer perform this service.
See Engine Coolant on page 9-16
for what to use. Inspect hoses.
Clean radiator, condenser, pressure
cap, and filler neck. Pressure test the
cooling system and pressure cap.
(k)Inspect belt for fraying, excessive
cracks, or obvious damage. Replace
belt if necessary.
(l)Drain, flush, and refill brake/clutch
hydraulic system at a regular service
interval (IorII) every two years.
This service can be complex; you
should have your dealer/retailer
perform this service. See Brakes
on page 9-22.
(m)This service can be complex;
you should have your dealer/retailer
perform this service.Owner Checks and
Services
These owner checks and services
should be performed at the intervals
specied to help ensure vehicle
safety, dependability, and
emission control performance.
Your dealer/retailer can assist with
these checks and services.
Be sure any necessary repairs are
completed at once. Whenever any
uids or lubricants are added to
the vehicle, make sure they are
the proper ones, as shown in
Recommended Fluids and
Lubricants on page 11-12.
At Each Fuel Fill
It is important to perform these
underhood checks at each fuel fill.
Engine Oil Level Check
Notice:It is important to check
the engine oil regularly and
keep it at the proper level.
Failure to keep the engine oil
at the proper level can cause
damage to the engine not covered
by the vehicle warranty.
Check the engine oil level and
add the proper oil if necessary.
SeeEngine Oil on page 9-7.
Engine Coolant Level Check
Check the engine coolant level
and add DEX-COOL®coolant
mixture if necessary. SeeEngine
Coolant on page 9-16.
Windshield Washer Fluid
Level Check
Check the windshield washer uid
level in the windshield washer
uid reservoir and add the proper
uid if necessary.
Service and Maintenance 11-9
ProCarManuals.com

Page 278 of 314

At Least Once a Month
Tire Ination Check
Inspect the vehicle’s tires and make
sure they are inated to the correct
pressures. Do not forget to check
the spare tire. SeeInflation - Tire
Pressure on page 9-47. Check to
make sure the spare tire is stored
securely. SeeChanging a Flat Tire
on page 9-61.
Tire Wear Inspection
Tire rotation may be required for
high mileage highway drivers prior to
the Engine Oil Life System service
notication. Check the tires for
wear and, if necessary, rotate the
tires. SeeTire Inspection and
Rotation on page 9-52.
At Least Once a Year
Starter Switch Check
{CAUTION
When you are doing this
inspection, the vehicle could move
suddenly. If the vehicle moves,
you or others could be injured.
1. Before starting this check, be
sure there is enough room
around the vehicle.
2. Firmly apply both the parking
brake and the regular brake.
SeeParking Brake on page 8-10.
Do not use the accelerator
pedal, and be ready to turn off
the engine immediately if it starts.
3. Try to start the engine in
each gear. The vehicle should
start only in P (Park) or
N (Neutral). If the vehicle starts
in any other position, contact
your dealer/retailer for service.
Automatic Transmission Shift
Lock Control System Check
{CAUTION
When you are doing this
inspection, the vehicle could move
suddenly. If the vehicle moves,
you or others could be injured.
1. Before starting this check, be
sure there is enough room
around the vehicle. It should be
parked on a level surface.
2. Firmly apply the parking brake.
SeeParking Brake on page 8-10.
Be ready to apply the regular
brake immediately if the vehicle
begins to move.
3. With the engine off, turn the
ignition to ON/RUN, but do not
start the engine. Without applying
the regular brake, try to move the
shift lever out of P (Park) with
normal effort. If the shift lever
moves out of P (Park), contact
your dealer/retailer for service.
11-10 Service and Maintenance
ProCarManuals.com

Page 307 of 314

Customer Information (cont.)
Reporting Safety Defects
to the United States
Government................12-14
Roadside Assistance
Program.......................12-6
Service Publications
Ordering Information.....12-15
D
Defensive Driving.................8-16
Delayed Headlamps............... 5-2
Doing Your Own
Service Work..................... 9-4
Dome Lamps ........................ 5-3
Door
Ajar Light........................4-23
Locks............................... 2-5
Power Door Locks.............. 2-6
Rear Door Security Locks.... 2-6
Driver Information
Center (DIC)....................4-25
DIC Operation and
Displays...............4-26, 4-32
DIC Warnings and
Messages....................4-36Driving
At Night..........................8-23
Before a Long Trip............8-25
Defensive........................8-16
Drunken..........................8-16
Highway Hypnosis............8-25
Hill and Mountain Roads....8-26
In Rain and on Wet
Roads.........................8-24
Rocking Your Vehicle to
Get it Out ....................8-29
Winter.............................8-27
Winter Mode Light............4-22
Driving for Better Fuel
Economy.........................8-15
E
EDR .................................12-16
Electrical System
Add-On Equipment............9-34
Engine Compartment
Fuse Block...................9-35
Fuses.............................9-35
Headlamp Wiring..............9-34
Rear Compartment Fuse
Block...........................9-37Engine
Air Cleaner/Filter...............9-11
Check and Service Engine
Soon Lamp..................4-18
Coolant...........................9-16
Coolant Temperature
Warning Light...............4-18
Drive Belt Routing...........11-15
Engine Compartment
Overview....................... 9-6
Exhaust...........................8-14
Oil ................................... 9-7
Oil Life System.................. 9-9
Overheating.....................9-18
Starting............................. 8-3
Engine Heater....................... 8-5
Entry Lighting........................ 5-3
Event Data Recorders.........12-16
Extender, Safety Belt............1-22
Exterior Lamps...................... 5-1
Exterior Lamps Off
Reminder........................4-23
INDEX i-3
ProCarManuals.com

Page:   < prev 1-10 11-20 21-30 next >