light SATURN VUE 2008 Owner's Guide

Setting Cruise Control
{CAUTION:
If you leave your cruise control on when you
are not using cruise, you might hit a button
and go into cruise when you do not want to.
You could be startled and even lose control.
Keep the cruise control switch off until you
want to use cruise control.
The cruise control buttons
are located on the left side
of the steering wheel.
E(On/Off):Press this button to turn the cruise control
system on and off. An indicator light comes on.
RES+ (Resume/Accel):Press the thumbwheel up to
resume a set speed or to accelerate to a higher speed.
−SET (Set/Coast):Press the thumbwheel down to
set a speed or to decrease the speed.
To set a speed do the following:
1. Press the on/off symbol to turn cruise control on.
The indicator light on the button comes on.
2. Get to the speed desired.
3. Press the thumbwheel toward−SET and release it.
4. Take your foot off the accelerator pedal.
When the brakes are applied, the cruise control
shuts off.
Resuming a Set Speed
If the cruise control is set at a desired speed and then
the brakes are applied, the cruise control is disengaged.
The indicator light on the instrument panel cluster goes
out when the cruise is no longer engaged. To return to
the previously set speed, press the thumbwheel up
toward RES+ briey when the vehicle has reached a
speed of about 25 mph (40 km/h) or more.
This accelerates your vehicle to the previously selected
speed.
3-12
ProCarManuals.com

Increasing Speed While Using Cruise
Control
There are two ways to go to a higher speed.
Disengage the cruise control, but do not turn it off.
If the cruise control system is already engaged,
press the thumbwheel up toward RES+ and hold it
until your vehicle accelerates to the desired speed,
and then release the switch. To increase the speed
in very small amounts, press the thumbwheel up
toward RES+ briey and then release it. Each
time this is done, the vehicle will go about 1 mph
(1.6 km/h) faster.
Reducing Speed While Using Cruise
Control
If the cruise control system is already engaged,
Push the thumbwheel toward−SET and hold until
the desired lower speed is reached, then release it.
To slow down in very small amounts, push the
thumbwheel toward−SET briey. Each time this is
done, the vehicle goes about 1 mph (1.6 km/h)
slower.
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase the vehicle’s
speed. When you take your foot off the pedal, the
vehicle will slow down to the previously set cruise
control speed.
Using Cruise Control on Hills
How well the cruise control works on hills depends upon
the vehicle’s speed, load, and the steepness of the
hills. When going up steep hills, you might have to
step on the accelerator pedal to maintain the vehicle’s
speed. When going downhill, you might have to brake
or shift to a lower gear to maintain the vehicle’s
speed. Of course, applying the brakes ends cruise
control. Many drivers nd this to be too much trouble
and do not use cruise control on steep hills.
Ending Cruise Control
There are three ways to disengage the cruise control:
Step lightly on the brake pedal or clutch; when
cruise control disengages, the indicator light on
the instrument panel cluster goes out.
Press the on/off button, this will turn off the cruise
control system.
3-13
ProCarManuals.com

Erasing Speed Memory
The cruise control set speed memory is erased when
the cruise control or the ignition is turned off.
Exterior Lamps
The exterior lamp control is
located on the instrument
panel to the left of the
steering wheel.
The exterior lamp control can be turned to the following
positions:
9(Off):This position turns off the exterior lamps.
The knob returns to the AUTO position after it is
released.
AUTO (Automatic):This position is the automatic
mode for headlamps. The exterior lamps turn on and
off, depending on outside lighting.
;(Parking Lamps):This position turns on the
parking lamps together with the following:
Sidemarker Lamps
Taillamps
License Plate Lamps
Instrument Panel Lights
2(Headlamps):This position turns on the
headlamps, together with the previously listed lamps
and lights.
Lamps On Reminder
A warning chime sounds, if the driver’s door is opened
while the ignition is off and the lamps are on.
Wiper Activated Headlamps
This feature automatically turns on the headlamps and
parking lamps if the exterior lamp control is set in the
AUTO position and the windshield wipers are turned on
and have completed eight wipe cycles. SeeExterior
Lamps on page 3-14for additional information.
When the ignition is turned off, the wiper-activated
headlamps immediately turn off. They also turn off if
the windshield wiper control is turned off.
3-14
ProCarManuals.com

Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier
for others to see the front of your vehicle during the day.
DRL can be helpful in many different driving conditions,
but they can be especially helpful in the short periods
after dawn and before sunset. Fully functional daytime
running lamps are required on all vehicles rst sold
in Canada.
The DRL system makes the low-beam headlamps come
on in daylight when the following conditions are met:
The engine is running,
The exterior lamp band is in AUTO, and
The light sensor determines it is daytime.
When the DRL are on, the low-beam headlamps will be
on. The taillamps, sidemarker, and other lamps will
not be on. The instrument panel will not be lit up either.
When the exterior lamp band is turned to the headlamp
position, the regular headlamps will come on. The other
lamps that come on with the headlamps will also
come on.
When the headlamps are turned off, the regular lamps
also turn off, and the low-beam headlamps turn on.
The regular headlamp system should be used when
needed.
Automatic Headlamp System
When it is dark enough outside, the headlamps come
on automatically.
There is a light sensor located on top of the instrument
panel. Make sure it is not covered, or the headlamps
will come on when they are not needed.
The system may also turn on the headlamps when
driving through a parking garage or tunnel.
3-15
ProCarManuals.com

Fog Lamps
If your vehicle has this feature, use the fog lamps for
better visibility in foggy or misty conditions.
Push the button with this
symbol to turn the fog
lamps on or off.
The fog lamp button is located on the instrument panel
next to the exterior lamps switch.
The fog lamp indicator in the instrument panel comes
on when the fog lamps are in use.
The parking lamps or low-beam headlamps must be on,
before the fog lamps can be turned on.
If the exterior lamp control is set to AUTO mode, the
parking lamps and low-beam headlamps come on
simultaneously when the fog lamps are turned on.When the high-beam headlamps are turned on, the fog
lamps turn off automatically. When the high-beam
headlamps are turned off, the fog lamps come on again.
Some localities have laws that require the headlamps
to be on along with the fog lamps.
Instrument Panel Brightness
This feature controls the brightness of the instrument
panel lights.
The thumbwheel for this
feature is located on the
left side of the steering
wheel next to the exterior
lamps control.
Turn the thumbwheel to the right to brighten the lights
or to the left to dim them.
3-16
ProCarManuals.com

Dome Lamp
*(Dome Lamp Override):Press this button to keep
the dome lamps and other interior lamps turned off while
any door is open. Press this button again to return it to the
out position and the lamps automatically come on when
any door is opened.
+(On/Off):Press this button to turn the dome
lamps on and off while the doors are closed.
Entry Lighting
If the dome lamp override button is in the out position,
the lamps inside the vehicle automatically come on
when any door is opened or when the Remote Keyless
Entry (RKE) unlock button is pressed. After the door is
opened the lights remain on and stay on for 20 seconds
after the doors are closed, or until the key is put into the
ignition and turned to the ACC/ACCESSORY position.
The lights will then gradually dim until it is no longer lit.
Reading Lamps
The reading lamps are located on the overhead console.
To turn the reading lamps on or off, press the button
located next to each lamp.
Battery Run-Down Protection
The battery saver feature is designed to protect your
vehicle’s battery.
If any interior or exterior lamp is left on and the ignition
is turned off, the battery rundown protection system
automatically turns the lamp off after 10 minutes.
3-17
ProCarManuals.com

6(Floor):This mode directs most of the air to the
oor outlets with some air directed to the windshield.
When this mode is selected, the system turns the
recirculation mode off. Recirculation mode cannot be
selected while in oor mode. This is to help prevent
window fogging.
The right knob can also be used to select defog or
defrost mode. See “Defogging and Defrosting” later in
this section.
#(Air Conditioning):Press this button to turn the
air conditioning system on or off. When this button
is pressed, an indicator light comes on to show that the
air conditioning is activated. The air conditioning can
be selected in any mode as long as the fan is on and
the outside temperature is above freezing. A ashing
indicator light indicates that the air conditioning
compressor is currently not available.
On hot days, open the windows to let hot inside air
escape; then close them. This helps to reduce the time
it takes for the vehicle to cool down. It also helps the
system to operate more efficiently.For quick cool down on hot days, select the following
settings together:
1. Select vent mode.
2. Select outside air.
3. Turn the air conditioning on.
4. Select the coolest temperature and highest fan
speed.
5. Once the vehicle’s interior temperature is below the
outside temperature, select recirculation mode for
enhanced cooling.
Using these settings together for long periods of time
may cause the air inside of the vehicle to become
too dry. To prevent this from happening, after the air
inside of the vehicle has cooled, turn the recirculation
mode off.
The air conditioning system removes moisture from the
air, so a small amount of water might drip underneath
the vehicle while idling or after turning off the engine.
This is normal.
;(Outside Air):Press this button to turn the outside
air mode on. An indicator light in the button comes on to
show that it is activated. Air from outside the vehicle will
circulate throughout the vehicle. The outside air mode
can be used with all modes, but it cannot be used with the
recirculation mode. Pressing this button will cancel the
recirculation mode.
3-20
ProCarManuals.com

@(Recirculation):Press this button to turn on the
recirculation mode. An indicator light in the button comes
on to show that it is activated. The air inside the vehicle
will be recirculated through the climate control system
and the vehicle, not from outside the vehicle. This mode
can be used to prevent outside air and odors from
entering the vehicle or to help heat or cool the air inside
the vehicle more quickly. Avoid using the recirculation
mode during high periods of humidity and cool outside
temperatures since this may result in increased window
fogging. If window fogging is experienced, select the
defrost mode.
Recirculation mode is not available in oor, defog or
defrost modes and will shut off automatically and change
to outside air. If the button is selected in these modes, the
indicator will ash. This helps prevent window fogging
and moisture building up within the cabin.
Defogging and Defrosting
Fog on the inside of windows is a result of high humidity
(moisture) condensing on the cool window glass. This
can be minimized if the climate control system is used
properly. There are two modes to clear fog or frost from
the windshield and side windows. Use the defog mode
to clear the windows of fog or moisture and warm thepassengers. Use the defrost mode to remove fog or frost
from the windshield more quickly. For best results, clear
all snow and ice from the windshield before defrosting.
Turn the right knob to select the defog or defrost mode.
-(Defog):This mode directs air to the windshield,
side window outlets and oor outlets. When this mode is
selected, the system will turn recirculation mode off and
run the air conditioning compressor unless the outside air
is at or below freezing. Recirculation mode cannot be
selected while in defog mode. This helps prevent window
fogging and moisture building up within the cabin.
To defog the windows faster, turn the temperature
knob clockwise to the warmest setting.
0(Defrost):This mode directs most of the air to the
windshield, with some air directed to the side window
outlets and the oor outlets. When this mode is selected,
the system will turn recirculation mode off automatically
and will run the air conditioning compressor unless
the outside air is at or below freezing. Recirculation
mode cannot be selected while in defrost mode.
This helps prevent window fogging and moisture
building up within the cabin. To defrost the windows
faster, turn the temperature knob clockwise to the
warmest setting.
3-21
ProCarManuals.com

Rear Window Defogger
The rear window defogger uses a warming grid to
remove fog from the rear window.
The rear window defogger only works when the ignition
is in ON/RUN.
<(Rear Window Defogger):Press the button to turn
the rear window defogger on or off. An indicator light
on the button comes on to show that the rear window
is activated.
The rear window defogger will stay on for approximately
10 minutes after the button is pressed, unless the ignition
is turned to ACC/ACCESSORY or LOCK/OFF. If turned
on again, the defogger only runs for approximately
ve minutes before turning off again. At higher vehicle
speeds, the defogger may stay on continuously.
The defogger can always be turned off by pressing
the button again or by turning off the engine.If your vehicle has the remote start feature, the rear
defogger will automatically turn on.
Notice:Do not use anything sharp on the inside
of the rear window. If you do, you could cut or
damage the warming grid, and the repairs would not
be covered by the vehicle warranty. Do not attach
a temporary vehicle license, tape, a decal or
anything similar to the defogger grid.
Remote Start Climate Control Operation
If your vehicle has the remote start feature and it
is activated, the climate control system heats and cools
the inside of the vehicle using the modes that were
set before the vehicle was turned off and the rear
defogger automatically turns on.
3-22
ProCarManuals.com

AUTO (Automatic Air Delivery Mode):Turn the
air delivery mode knob to AUTO for the system to
automatically control the direction of the airow to help
reach the desired inside temperature.
The system automatically controls the air inlet to supply
the outside air or recirculated inside air needed to heat
or cool the vehicle faster. The indicator light on the
recirculation button will be lit whenever the system
switches to recirculation.
You can switch to outside air by pressing the outside
air button. However, the recirculation mode may
turn back on automatically.
In cold weather, if the fan and air delivery modes are in
automatic, the system starts at lower fan speeds to avoid
directing cold air into the vehicle until warmer air is
available. The climate control system directs air to the
oor, but may automatically change modes as the vehicle
warms up to maintain the chosen temperature setting.
The length of time needed to warm the interior depends
on the outside temperature and inside temperature of
the vehicle.Manual Operation
To change the current fan speed, turn the left knob.
A(Fan):Turn the left knob clockwise or
counterclockwise to increase or decrease the fan speed.
To turn the fan off, turn the left knob to the
9position.
In any setting other than off, the fan runs continuously
with the ignition on. The fan must be turned on to run the
air conditioning compressor. There will be some airow
noticeable from the various outlets when driving, even
with the fan in the off position. This is to ensure some
fresh air is always available in the vehicle. To turn off
the air completely, turn the fan to
9and select the
recirculation button.
Temperature Control:Select the desired cabin air
temperature between 60-90°F (16-32°C). Typically,
the best setting is near 75°F (23°C). Choosing the
coldest or warmest temperature setting does not
cause the system to heat or cool any faster.
3-24
ProCarManuals.com