light SATURN VUE 2008 Service Manual

To change the current air delivery mode, use the right
knob to select one of the following:
H(Vent):This mode directs air to the instrument
panel outlets.
)(Bi-Level):This mode splits the air between the
instrument panel outlets and the oor outlets.
6(Floor):This mode directs most of the air to the
oor outlets with some air directed to the windshield.
When this mode is selected, the system turns the
recirculation mode off. Recirculation mode cannot be
selected while in oor mode. This is to help prevent
window fogging.
The right knob can also be used to select defog or
defrost mode. See “Defogging and Defrosting” later in
this section.
#(Air Conditioning):Press this button to turn the
air conditioning system on or off. When this button
is pressed, an indicator light comes on to show that
the air conditioning is activated. The air conditioning can
be selected in any mode as long as the fan is on and
the outside temperature is above freezing. A ashing
indicator light indicates that the air conditioning
compressor is currently not available.On hot days, use the automatic fan and air delivery
mode settings and the vehicle will reach the desired
temperature more quickly. The desired fan and air
delivery mode settings can still be adjusted manually.
Open the windows to let the hot inside air escape, then
close them. This helps reduce the time it takes for
the vehicle to cool down and helps the system to
operate more efficiently.
For quick cool down on hot days, select the following
settings together:
1. Select vent mode.
2. Select outside air.
3. Turn the air conditioning on.
4. Select the coolest temperature and highest fan
speed.
5. Once the vehicle’s interior temperature is below the
outside temperature, select recirculation mode for
enhanced cooling.
Using these settings together for long periods of time
may cause the air inside of the vehicle to become
too dry. To prevent this from happening, after the air
inside of the vehicle has cooled, turn the recirculation
mode off.
The air conditioning system removes moisture from the
air, so a small amount of water might drip underneath
the vehicle while idling or after turning off the engine.
This is normal.
3-25
ProCarManuals.com

;(Outside Air):Press this button to turn the
outside air mode on. An indicator light in the button
comes on to show that it is activated. Air from outside
the vehicle will circulate throughout the vehicle.
The outside air mode can be used with all modes,
but it cannot be used with the recirculation mode.
Pressing this button will cancel the recirculation mode.
@(Recirculation):Press this button to turn on
the recirculation mode. An indicator light in the button
comes on to show that it is activated. The air inside the
vehicle will be recirculated through the climate control
system and the vehicle, not from outside the vehicle.
This mode can be used to prevent outside air and odors
from entering the vehicle or to help heat or cool the
air inside the vehicle more quickly. Avoid using
the recirculation mode during high periods of humidity
and cool outside temperatures since this may result
in increased window fogging. If window fogging is
experienced, select the defrost mode.
Recirculation mode is not available in oor, defog or
defrost modes and will shut off automatically and change
to outside air. If the button is selected in these modes,
the indicator will ash. This helps prevent window
fogging and moisture building up within the cabin.
Defogging and Defrosting
Fog on the inside of windows is a result of high humidity
(moisture) condensing on the cool window glass. This
can be minimized if the climate control system is used
properly. There are two modes to clear fog or frost from
the windshield and side windows. Use the defog mode
to clear the windows of fog or moisture and warm the
passengers. Use the defrost mode to remove fog or frost
from the windshield more quickly. For best results, clear
all snow and ice from the windshield before defrosting.
When using the automatic mode setting, the system will
automatically use the defog or defrost modes as needed.
Manually turn the right knob to select the defog or
defrost mode.
-(Defog):This mode directs air to the windshield,
side window outlets and oor outlets. When this mode is
selected, the system will turn recirculation mode off and
run the air conditioning compressor unless the outside air
is at or below freezing. Recirculation mode cannot be
selected while in defog mode. This helps prevent window
fogging and moisture building up within the cabin.
3-26
ProCarManuals.com

0(Defrost):This mode directs most of the air to the
windshield, with some air directed to the side window
outlets and the oor outlets. When this mode is selected,
the system will turn recirculation mode off automatically
and will run the air conditioning compressor unless
the outside air is at or below freezing. Recirculation
mode cannot be selected while in defrost mode.
This helps prevent window fogging and moisture
building up within the cabin.
Rear Window Defogger
The rear window defogger uses a warming grid to
remove fog from the rear window.
The rear window defogger only works when the ignition
is in ON/RUN.
<(Rear Window Defogger):Press the button to turn
the rear window defogger on or off. An indicator light
on the button comes on to show that the rear window
defogger is activated.The rear window defogger will stay on for approximately
10 minutes after the button is pressed, unless the ignition
is turned to ACC/ACCESSORY or LOCK/OFF. If turned
on again, the defogger only runs for approximately
ve minutes before turning off. At higher vehicle speeds,
the defogger may stay on continuously. The defogger can
always be turned off by pressing the button again or by
turning off the engine.
If your vehicle has the remote start feature, the rear
defogger will automatically turn on.
Notice:Do not use anything sharp on the inside
of the rear window. If you do, you could cut or
damage the warming grid, and the repairs would
not be covered by the vehicle warranty. Do not
attach a temporary vehicle license, tape, a decal
or anything similar to the defogger grid.Remote Start Climate Control Operation
If your vehicle has the remote start feature and it
is activated, the climate control system heats and cools
the inside of the vehicle using the modes that were
set before the vehicle was turned off and the rear
defogger automatically turns on.
3-27
ProCarManuals.com

5. Remove the lter cover and pull out the old air lter.
6. Install the new air lter.
7. Reinstall the air lter cover. Reconnect the wire
cabling and re-install the glove box.
See your dealer/retailer if additional assistance is
needed.
Warning Lights, Gages, and
Indicators
This section describes the warning lights and gages on
the vehicle.
Warning lights and gages can signal that something is
wrong before it becomes serious enough to cause
an expensive repair or replacement. Paying attention to
the warning lights and gages could prevent injury.
Warning lights come on when there may be or is a
problem with one of the vehicle’s functions. Some
warning lights come on briey when the engine is started
to indicate they are working.
Gages can indicate when there may be or is a problem
with one of the vehicle’s functions. Often gages and
warning lights work together to indicate a problem with
the vehicle.
When one of the warning lights comes on and stays on
while driving, or when one of the gages shows there
may be a problem, check the section that explains what
to do. Follow this manual’s advice. Waiting to do
repairs can be costly and even dangerous.
3-30
ProCarManuals.com

Speedometer and Odometer
The speedometer lets you see your speed in both miles
per hour (mph) and kilometers per hour (km/h).
The odometer shows how far your vehicle has been
driven, in either miles or kilometers.
If your vehicle needs a new odometer installed, the new
one will be set to the mileage total of the old odometer.
If it cannot, it will be set at zero and a label must be
put on the driver’s door to show the old mileage reading
when the new odometer was installed. If the mileage
is unknown, the label should then indicate “previous
mileage unknown.”
Trip Odometer
The trip odometer can record the number of miles, used
in the United States, or kilometers, used in Canada,
traveled for up to two trips.
You can cycle between the odometer and trip
odometers A and B by pressing the reset button
located in the lower right area of the speedometer.
By pressing the reset button, you can tell how many miles
or kilometers have been recorded on either Trip A or
Trip B since you last set the trip odometer back to zero.
To reset each trip odometer to zero, press and hold
the reset button. The reset button resets only the
trip odometer that is being displayed. Each trip
odometer must be reset individually.
Tachometer
The tachometer displays the engine speed in revolutions
per minute (rpm).
Safety Belt Reminders
Safety Belt Reminder Light
When the engine is started, a chime will come on for
several seconds to remind people to fasten their safety
belts, unless the driver’s safety belt is already buckled.
The safety belt light will
also come on and stay
on for several seconds,
then it will ash for
several more.
This chime and light is repeated if the driver remains
unbuckled and the vehicle is in motion. If the driver’s belt
is already buckled, neither the chime nor the light will
come on.
3-32
ProCarManuals.com

Passenger Safety Belt Reminder Light
Several seconds after the engine is started, a chime will
sound for several seconds to remind the front passenger
to buckle their safety belt. This would only occur if the
passenger airbag is enabled. SeePassenger Sensing
System on page 1-65for more information. The
passenger safety belt light will also come on and stay on
for several seconds, then it will ash for several more.
This chime and light are
repeated if the passenger
remains unbuckled and
the vehicle is in motion.
If the passenger’s safety belt is buckled, neither the
chime nor the light will come on.
Airbag Readiness Light
There is an airbag readiness light on the instrument
panel cluster, which shows the airbag symbol.
The system checks the airbag’s electrical system for
malfunctions. The light tells you if there is an electrical
problem. The system check includes the airbag sensor,
the airbag modules, the wiring and the crash sensing and
diagnostic module. For more information on the airbag
system, seeAirbag System on page 1-55.
This light will come on
when you start your
vehicle, and it will ash for
a few seconds. The light
should go out and the
system is ready.
3-33
ProCarManuals.com

If the airbag readiness light stays on after you start
the vehicle or comes on when you are driving,
your airbag system may not work properly. Have
your vehicle serviced right away.
{CAUTION:
If the airbag readiness light stays on after you
start your vehicle, it means the airbag system
may not be working properly. The airbags in
your vehicle may not inate in a crash, or they
could even inate without a crash. To help
avoid injury to yourself or others, have your
vehicle serviced right away.
The airbag readiness light should ash for a few
seconds when the engine is started. If the light does not
come on then, have it xed so it will be ready to warn
you if there is a problem.
Passenger Airbag Status Indicator
Your vehicle has the passenger sensing system.
Your instrument panel has a passenger airbag status
indicator.
When you start the vehicle, the passenger airbag status
indicator will light ON and OFF, or the symbol for on
and off, for several seconds as a system check. Then,
after several more seconds, the status indicator will
light either ON or OFF, or either the on or off symbol to
let you know the status of the right front passenger’s
frontal airbag.
If the word ON or the on symbol is lit on the passenger
airbag status indicator, it means that the right front
passenger’s frontal airbag is enabled (may inate).United States
Canada
3-34
ProCarManuals.com

If, after several seconds, both status indicator lights
remain on, or if there are no lights at all, there may
be a problem with the lights or the passenger sensing
system. See your dealer/retailer for service.
{CAUTION:
If the airbag readiness light in the instrument
panel cluster ever comes on and stays on,
it means that something may be wrong with
the airbag system. If this ever happens, have
the vehicle serviced promptly, because an
adult-size person sitting in the right front
passenger’s seat may not have the protection
of the airbag(s). SeeAirbag Readiness Light
on page 3-33for more on this, including
important safety information.
Charging System Light
This light will come on
briey when the ignition is
turned on, and the engine
is not running, as a check
to show you it is working.
It should go out when the engine is started. If it stays
on, or comes on while you are driving, you may have a
problem with the electrical charging system. Have it
checked by your dealer/retailer. Driving while this light is
on could drain your battery. If you must drive a short
distance with the light on, be certain to turn off all your
accessories, such as the radio and air conditioner to
help reduce the drain on the battery.
3-36
ProCarManuals.com

Brake System Warning Light
This light should come on briey when the engine is
started.
If it does not come on, have it xed so it will be ready to
warn you if there is a problem.
When the ignition is on, the brake system warning light
will come on when the parking brake is set. The light will
stay on if the parking brake does not release fully. If it
stays on after the parking brake is fully released, there is
a brake problem. Have your brake system inspected
immediately.
If the light comes on while driving, a chime will sound.
Pull off the road and stop. The pedal might be harder to
push or go closer to the oor. It might also take longer
to stop. If the light is still on, have the vehicle towed
for service. SeeTowing Your Vehicle on page 4-41.
{CAUTION:
Your brake system may not be working
properly if the brake system warning light is
on. Driving with the brake system warning light
on can lead to an accident. If the light is still
on after you have pulled off the road and
stopped carefully, have the vehicle towed
for service.
Anti-lock Brake System (ABS)
Warning Light
For vehicles with
the Antilock Brake
System (ABS), this light
will come on briey, as a
check, when you start your
vehicle.
If it does not, have your vehicle serviced so that the
light works properly when it needs to. United States
Canada
3-37
ProCarManuals.com

If the light stays on longer than a few seconds after you
start your engine, or comes on and stays on while
you are driving, try resetting the system. To reset the
system:
1. If you are driving, pull over when it is safe to do so.
2. Place the vehicle in PARK (P).
3. Turn off the ignition.
4. Then restart the engine.
If the light remains on after resetting the system or
comes on again while driving, your vehicle needs
service. If the ABS light is on, but the regular brake
system warning light is not on, the antilock brakes are
not working properly, but the regular brakes are still
functioning. Have your vehicle serviced right away.
If both brake lights are on, you do not have antilock
brakes, and there’s a problem with your regular
brakes as well. Have your vehicle towed for service.
SeeTowing Your Vehicle on page 4-41.Speed Sensitive Power
Steering (SSPS) Warning Light
This warning light will come
on briey when you turn the
ignition to ON as a check to
show you it is working.
Then it should go out after a few seconds.
If the warning light does not come on, have it xed so it
will be able to warn you if there is a problem.
If the warning light stays on, or comes on while you are
driving, the SSPS system may not be working. If this
happens, see your dealer/retailer for service.
3-38
ProCarManuals.com