warning light SATURN VUE 2009 User Guide

Passenger Safety Belt
Reminder Light
Several seconds after the engine
is started, a chime sounds for
several seconds to remind the front
passenger to buckle their safety belt.
This only occurs if the passenger
airbag is enabled. SeePassenger
Sensing System on page 1-51for
more information. The passenger
safety belt light, located on the
instrument panel, comes on and
stays on for several seconds and
then ashes for several more.
This chime and light are repeated if
the passenger remains unbuckled
and the vehicle is in motion.
If the passenger safety belt is
buckled before the engine is started,
neither the chime nor the light
comes on.The front passenger safety belt
warning light and chime may turn on
if an object is put on the seat such as
a briefcase, handbag, grocery bag,
laptop or other electronic device.
To turn off the warning light and or
chime, remove the object from the
seat or buckle the safety belt.
Airbag Readiness Light
There is an airbag readiness light
on the instrument panel cluster,
which shows the airbag symbol.
The system checks the airbag’s
electrical system for malfunctions.
The light indicates if there is an
electrical problem. The system
check includes the airbag sensor,
the pretensioners, the airbag
modules, the wiring and the crash
sensing and diagnostic module.
For more information on the airbag
system, seeAirbag System on
page 1-42.
{CAUTION
If the airbag readiness light stays
on after the vehicle is started or
comes on while driving, it means
the airbag system might not be
working properly. The airbags in
the vehicle might not inate in a
crash, or they could even inate
without a crash. To help avoid
injury, have the vehicle serviced
right away.
The airbag readiness light comes
on when the vehicle is started, and
ashes for a few seconds. The light
goes out when the system is ready.
Instrument Panel 3-29
ProCarManuals.com

If the airbag readiness light stays on
after the vehicle is started or comes
on while driving, the airbag system
may not work properly. Have the
vehicle serviced right away.
The airbag readiness light should
ash for a few seconds when the
engine is started. If the light does
not come on then, have it xed
immediately. If there is a problem
with the airbag system, an airbag
Driver Information Center (DIC)
message may also come on. See
DIC Warnings and Messages on
page 3-49for more information.Passenger Airbag Status
Indicator
The vehicle has the passenger
sensing system. SeePassenger
Sensing System on page 1-51
for important safety information.
The instrument panel has a
passenger airbag status indicator.When the vehicle is started, the
passenger airbag status indicator will
light ON and OFF, or the symbol for
on and off, for several seconds as a
system check. Then, after several
more seconds, the status indicator
will light either ON or OFF, or either
the on or off symbol to let you know
the status of the right front passenger
frontal and seat-mounted side impact
airbags.
If the word ON or the on symbol is
lit on the passenger airbag status
indicator, it means that the right
front passenger frontal airbag and
seat-mounted side impact airbag
are enabled (may inate).
If the word OFF or the off symbol
is lit on the airbag status indicator,
it means that the passenger sensing
system has turned off the right front
passenger frontal airbag and
seat-mounted side impact airbag. United States
Canada
3-30 Instrument Panel
ProCarManuals.com

If, after several seconds, both
status indicator lights remain on,
or if there are no lights at all, there
may be a problem with the lights
or the passenger sensing system.
See your dealer/retailer for service.
{CAUTION
If the airbag readiness light ever
comes on and stays on, it means
that something may be wrong with
the airbag system. To help avoid
injury to yourself or others, have
the vehicle serviced right away.
SeeAirbag Readiness Light on
page 3-29for more information,
including important safety
information.
Charging System Light
The charging system light comes on
briey when the ignition is turned on,
but the engine is not running, as a
check to show the light is working.
It should go out when the engine is
started.
If the light stays on, or comes
on while driving, there could be a
problem with the electrical charging
system. Have it checked by your
dealer/retailer. Driving while this light
is on could drain the battery.
If a short distance must be driven
with the light on, be sure to turn
off all accessories, such as the
radio and air conditioner.
Brake System Warning
Light
The brake indicator light should
come on briey as the engine
is started. If it does not come
on have the vehicle serviced
by your dealer/retailer.
When the ignition is on, the
brake system warning light comes
on when the parking brake is set.
The light stays on if the parking
brake does not fully release.
United StatesCanada
Instrument Panel 3-31
ProCarManuals.com

If it stays on after the parking brake
is fully released, there is a brake
problem. Have the brake system
inspected immediately.
{CAUTION
The brake system might not be
working properly if the brake
system warning light is on. Driving
with the brake system warning
light on can lead to a crash. If the
light is still on after the vehicle
has been pulled off the road and
carefully stopped, have the
vehicle towed for service.
If the light comes on while driving,
a chime sounds. Pull off the road and
stop. The pedal might be harder to
push or go closer to the oor. It might
also take longer to stop. If the light is
still on, have the vehicle towed for
service. SeeTowing Your Vehicle
on page 4-32.
Antilock Brake System
(ABS) Warning Light
For vehicles with the Antilock Brake
System (ABS), this light should come
on briey as the engine is started. If it
does not come on have the vehicle
serviced by your dealer/retailer.
If the ABS light stays on longer than
a few seconds after engine is started,
or comes on and stays on while
driving, try resetting the system.
To reset the system:
1. While driving, pull over when it is
safe to do so.
2. Place the vehicle in P (PARK).
3. Turn off the ignition.
4. Then restart the engine.If the ABS light remains on after
resetting the system or comes on
again while driving, the vehicle
needs service. If the ABS light is on,
but the regular brake system warning
light is not on, the antilock brakes are
not working properly, but the regular
brakes are still functioning. Have the
vehicle serviced right away. If both
brake lights are on, the vehicle does
not have antilock brakes, and there
is a problem with the regular brakes
as well. Have the vehicle towed for
service. SeeTowing Your Vehicle
on page 4-32.
3-32 Instrument Panel
ProCarManuals.com

Power Steering Warning
Lights
For 4-cylinder vehicles with Electric
Power Steering (EPS), this light
comes on briey when the ignition
is turned to ON/RUN as a check
to show it is working.
If it does not come on have the
vehicle serviced by your dealer/
retailer.
If the EPS light stays on, or comes
on while driving, the EPS system
may not be working. If this happens,
see your dealer/retailer for service.
Traction Control System
(TCS) Warning Light
The Traction Control System (TCS)
Warning Light shows one of these
two symbols.
This light comes on briey as the
engine is started. If it does not come
on have the vehicle serviced by
your dealer/retailer.
It also comes on when the Traction
Control System (TCS) has been
turned off or when the Electronic
Stability Program (ESP) is not ready.
If there is a problem with the TCS
or the ESP, this light and the TCS
warning light comes on at the
same time. SeeTraction Control
System (TCS) on page 4-8and
StabiliTrak
®System on page 4-7
for more information.
StabiliTrak®Indicator
Light
The StabiliTrak®light comes on
briey as the engine is started.
If it does not come on have
the vehicle serviced by your
dealer/retailer.
This light ashes while the
StabiliTrack or the Traction Control
System (TCS) is working. The light
comes on when the ESP has been
turned off and if there is a problem
with the StabiliTrak or the TCS.
SeeTraction Control System (TCS)
on page 4-8andStabiliTrak
®System
on page 4-7for more information.
Instrument Panel 3-33
ProCarManuals.com

Engine Coolant
Temperature Warning
Light
The engine coolant temperature
light should come on briey as
the engine is started. If it does not
come on have the vehicle serviced
by your dealer/retailer.
Notice:Driving with the engine
coolant temperature warning light
on could cause the vehicle to
overheat. SeeEngine Overheating
on page 5-25. The vehicle’s engine
could be damaged, and it might
not be covered by the vehicle
warranty. Never drive with the
engine coolant temperature
warning light on.If this light comes on and stays on,
the engine has overheated. Pull over
and seeEngine Overheating on
page 5-25for more information.Tire Pressure Light
If the vehicle has a tire pressure
monitoring system, the tire pressure
light provides information about tire
pressures and the Tire Pressure
Monitoring System. The light should
come on briey as the engine is
started. If it does not, have the
vehicle serviced by your dealer/
retailer.When the Light is On Steady
This indicates that one or
more of the tires are signicantly
underinated.
A tire pressure message in the
Driver Information Center (DIC),
can accompany the light. SeeDIC
Warnings and Messages on
page 3-49for more information.
Stop and check the tires as soon
as it is safe to do so. If underinated,
inate to the proper pressure.
SeeTires on page 5-43for more
information.
When the Light Flashes First and
Then is On Steady
This indicates that there could be
a problem with the Tire Pressure
Monitor System. The light ashes
for about a minute and stays on
steady for the remainder of the
ignition cycle. This sequence
repeats with every ignition cycle.
SeeTire Pressure Monitor System
on page 5-51for more information.
3-34 Instrument Panel
ProCarManuals.com

Low Washer Fluid
Warning Light
The low washer uid warning light
comes on when the windshield
washer uid is low. SeeWindshield
Washer Fluid on page 5-27for
more information.
All-Wheel Drive Disabled
Light
This light comes on when there
is a malfunction in the All-Wheel
Drive (AWD) system.This light ashes when the AWD
system is temporarily disabled.
For more information seeAll-Wheel
Drive (AWD) System on page 4-9.
Gate Ajar Light
If the gate ajar light comes on,
the liftgate is not completely closed.
Driving with the liftgate open can
cause carbon monoxide (CO) to
enter the vehicle.
SeeEngine Exhaust on page 2-28
for more information.
Door Ajar Light
The door ajar light comes on when a
door is open. Before driving, check
that all doors are properly closed.
Service Vehicle Soon
Light
The service vehicle soon light
comes on if a condition exists
that may require the vehicle to
be taken in for service.
If the light comes on, take the
vehicle to your dealer/retailer for
service as soon as possible.
3-40 Instrument Panel
ProCarManuals.com

Fuel Gage
When the ignition is on, the fuel
gage indicates how much fuel is
left in the tank.
When the indicator nears empty,
the low fuel light comes on. There is
still a little fuel left, but the fuel tank
should be relled soon. SeeLow
Fuel Warning Light on page 3-41
for more information.
An arrow on the fuel gage indicates
the side of the vehicle the fuel
door is on.Here are four things that some
owners ask about. None of these
means the fuel gage is not working
properly:
At the service station, the fuel
pump shuts off before the
gage reads full.
It takes a little more or less fuel
to ll up than the gage indicated.
For example, the gage may have
indicated the tank was half full,
but it actually took a little more or
less than half the tank’s capacity
to ll the tank.
The gage moves a little while
turning a corner or speeding up.
The gage takes a few seconds to
stabilize after the ignition is turned
on, but it goes back to empty
when the ignition is turned off.
For fuel tank capacity, see
Capacities and Specifications
on page 5-86.
Low Fuel Warning Light
The low fuel warning light, below
the fuel gage, comes on briey when
the engine is started.
This light also comes on when the
fuel tank is low on fuel. When fuel is
added, the light should go off. If it
does not, have the vehicle serviced. United StatesCanada
Instrument Panel 3-41
ProCarManuals.com

If the DIC display does not show a
heading, for example, N for North,
or the heading does not change after
making turns, there may be a strong
magnetic eld interfering with the
compass. Such interference may
be caused by a magnetic CB or cell
phone antenna mount, a magnetic
emergency light, magnetic note pad
holder, or any other magnetic item.
Turn off the vehicle, move the
magnetic item, then turn on the
vehicle and calibrate the compass.
To calibrate the compass, use the
following procedure:
Compass Calibration Procedure
1. Before calibrating the compass,
make sure the compass is set to
the variance zone in which the
vehicle is located. See “Compass
Variance (Zone) Procedure”
earlier in this section.Do not operate any switches
such as window, sunroof, climate
controls, seats, etc. during the
calibration procedure.
2. Press the vehicle information
button until PRESS
VTO
CALIBRATE COMPASS
displays.
3. Press the set/reset button to start
the compass calibration.
4. The DIC will display
CALIBRATING COMPASS:
TURN IN CIRCLES. Drive the
vehicle in tight circles at less than
5 mph (8 km/h) to complete the
calibration. The DIC will display
COMPASS CALIBRATION
COMPLETE for a few seconds
when the calibration is complete.
The DIC display will then return to
the previous menu.
DIC Warnings and
Messages
Messages are displayed on the DIC
to notify the driver that the status
of the vehicle has changed and that
some action may be needed by
the driver to correct the condition.
Multiple messages may appear
one after another.
Some messages may not require
immediate action, but you can
press any of the DIC buttons,
or the trip odometer reset stem
on the instrument panel cluster to
acknowledge that you received the
messages and to clear them from
the display.
Some messages cannot be cleared
from the DIC display because they
are more urgent. These messages
require action before they can be
cleared. Take any messages that
appear on the display seriously
and remember that clearing the
messages will only make the
messages disappear, not correct
the problem.
Instrument Panel 3-49
ProCarManuals.com

CHECK TIRE PRESSURE
On vehicles with the Tire Pressure
Monitor System (TPMS), this
message displays when the pressure
in one or more of the vehicle’s tires
needs to be checked. This message
also displays LEFT FRONT, RIGHT
FRONT, LEFT REAR, or RIGHT
REAR to indicate which tire needs to
be checked. You can receive more
than one tire pressure message at a
time. To read the other messages
that may have been sent at the same
time, press the set/reset button. If a
tire pressure message appears on
the DIC, stop as soon as you can.
Have the tire pressures checked
and set to those shown on the Tire
Loading Information label. SeeTires
on page 5-43,Loading the Vehicle
on page 4-28, andInflation - Tire
Pressure on page 5-49. The DIC
also shows the tire pressure values.
SeeDIC Operation and Displays on
page 3-42. If the tire pressure is low,
the low tire pressure warning light
comes on. SeeTire Pressure Light
on page 3-34.
COMPASS CALIBRATION
COMPLETE
This message displays when the
compass calibration is complete.
SeeDIC Compass on page 3-47.
CRUISE CONTROL SET
TO XXX
This message displays whenever
the cruise control is set. SeeCruise
Control on page 3-9for more
information.
DRIVER DOOR OPEN
This message displays when the
driver door is not closed properly.
Close the door completely.
ENGINE HOT A/C
(Air Conditioning) OFF
This message displays when the
engine coolant becomes hotter than
the normal operating temperature.
To avoid added strain on a hotengine, the air conditioning
compressor is automatically turned
off. When the coolant temperature
returns to normal, the A/C operation
automatically resumes. You can
continue to drive your vehicle.
ENGINE OVERHEATED IDLE
ENGINE
Notice:If you drive your vehicle
while the engine is overheating,
severe engine damage may occur.
If an overheat warning appears
on the instrument panel cluster
and/or DIC, stop the vehicle as
soon as possible. Do not increase
the engine speed above normal
idling speed. SeeEngine
Overheating on page 5-25for
more information.
This message displays when the
engine coolant temperature is
too hot. Stop and allow the vehicle
to idle until it cools down.
Instrument Panel 3-51
ProCarManuals.com