instrument panel SATURN VUE 2009 Workshop Manual

Malfunction
Indicator Lamp
Check Engine Light
A computer system called OBD II
(On-Board Diagnostics-Second
Generation) monitors operation of
the fuel, ignition, and emission
control systems. It ensures
that emissions are at acceptable
levels for the life of the vehicle,
helping to produce a cleaner
environment.
This light comes on when the
ignition is on, but the engine is not
running, as a check to show it is
working. If it does not, have the
vehicle serviced by your dealer/
retailer.If the check engine light comes
on and stays on, while the engine
is running, this indicates that there
is an OBD II problem and service
is required.
Malfunctions often are indicated by
the system before any problem is
apparent. Being aware of the light
can prevent more serious damage
to the vehicle. This system assists
the service technician in correctly
diagnosing any malfunction.
Notice:If the vehicle is
continually driven with this light
on, after a while, the emission
controls might not work as well,
the vehicle’s fuel economy might
not be as good, and the engine
might not run as smoothly.
This could lead to costly repairs
that might not be covered by
the vehicle warranty.Notice:Modications made
to the engine, transmission,
exhaust, intake, or fuel system
of the vehicle or the replacement
of the original tires with other
than those of the same Tire
Performance Criteria (TPC) can
affect the vehicle’s emission
controls and can cause this light
to come on. Modications to these
systems could lead to costly
repairs not covered by the vehicle
warranty. This could also result
in a failure to pass a required
Emission Inspection/Maintenance
test. SeeAccessories and
Modifications on page 5-3.
This light comes on during a
malfunction in one of two ways:
Light Flashing:A misre condition
has been detected. A misre
increases vehicle emissions and
could damage the emission control
system on the vehicle. Diagnosis
and service might be required.
Instrument Panel 3-35
ProCarManuals.com

The following can prevent more
serious damage to the vehicle:
Reduce vehicle speed.
Avoid hard accelerations.
Avoid steep uphill grades.
If towing a trailer, reduce the
amount of cargo being hauled
as soon as it is possible.
If the light continues to ash,
when it is safe to do so, stop
the vehicle. Find a safe place to
park the vehicle. Turn the key
off, wait at least 10 seconds, and
restart the engine. If the light is
still ashing, follow the previous
steps and see your dealer/retailer
for service as soon as possible.
Light On Steady:An emission
control system malfunction has been
detected on the vehicle. Diagnosis
and service might be required.An emission system malfunction
might be corrected by checking the
following items:
Make sure the fuel cap is fully
installed. SeeFilling the Tank
on page 5-8. The diagnostic
system can determine if the fuel
cap has been left off or improperly
installed. A loose or missing fuel
cap allows fuel to evaporate into
the atmosphere. A few driving
trips with the cap properly
installed should turn the light off.
If the vehicle has been driven
through a deep puddle of water,
the vehicle’s electrical system
might be wet. The condition is
usually corrected when the
electrical system dries out.
A few driving trips should turn
the light off.
Make sure to fuel the vehicle
with quality fuel. Poor fuel quality
causes the engine not to run as
efficiently as designed and may
cause: stalling after start-up,
stalling when the vehicle is
changed into gear, misring,
hesitation on acceleration,
or stumbling on acceleration.
These conditions might go away
once the engine is warmed up.
If one or more of these conditions
occurs, change the fuel brand
used. It will require at least one
full tank of the proper fuel to turn
the light off.
SeeGasoline Octane on
page 5-5.
If none of the above have made the
light turn off, your dealer/retailer can
check the vehicle. The dealer/retailer
has the proper test equipment and
diagnostic tools to x any mechanical
or electrical problems that might
have developed.
3-36 Instrument Panel
ProCarManuals.com

Emissions Inspection and
Maintenance Programs
Some state/provincial and local
governments have or might begin
programs to inspect the emission
control equipment on the vehicle.
Failure to pass this inspection
could prevent getting a vehicle
registration.
Here are some things to know to
help the vehicle pass an inspection:
The vehicle will not pass this
inspection if the check engine
light is on with the engine
running, or if the key is in
ON/RUN and the light is not on.
The vehicle will not pass
this inspection if the OBD II
(on-board diagnostic) system
determines that critical emission
control systems have not
been completely diagnosed
by the system. The vehicle
would be considered not readyfor inspection. This can happen
if the battery has recently been
replaced or if the battery has run
down. The diagnostic system is
designed to evaluate critical
emission control systems during
normal driving. This can take
several days of routine driving.
If this has been done and the
vehicle still does not pass the
inspection for lack of OBD II
system readiness, your dealer/
retailer can prepare the vehicle
for inspection.
Oil Pressure Light
{CAUTION
Do not keep driving if the oil
pressure is low. The engine can
become so hot that it catches re.
Someone could be burned. Check
the oil as soon as possible and
have the vehicle serviced.Notice:Lack of proper engine oil
maintenance can damage the
engine. The repairs would not be
covered by the vehicle warranty.
Always follow the maintenance
schedule in this manual for
changing engine oil.
The oil pressure light should come
on briey as the engine is started. If it
does not come on have the vehicle
serviced by your dealer/retailer.
If the light comes on and stays on, it
means that oil is not owing through
the engine properly. The vehicle
could be low on oil and might have
some other system problem.
Instrument Panel 3-37
ProCarManuals.com

Change Engine Oil Light
When the change engine oil light
comes on, it means that service is
required on the vehicle.
SeeScheduled Maintenance
on page 6-3andEngine Oil on
page 5-14for more information.
After the engine oil is changed the
engine oil life system needs to be
reset in order to turn off this light.
SeeEngine Oil Life System on
page 5-16for more information.
Security Light
For information regarding this light
and the vehicle’s security system,
seePASS-Key
®III+ Electronic
Immobilizer on page 2-13.
Fog Lamp Light
The fog lamp light comes on when
the fog lamps are in use.The light goes out when the fog
lamps are turned off. SeeFog
Lamps on page 3-14for more
information.
Cruise Control Light
The cruise control light comes on
whenever the cruise control is set.
The light goes out when the
cruise control is turned off.
SeeCruise Control on page 3-9
for more information.
3-38 Instrument Panel
ProCarManuals.com

Reduced Engine Power
Light
The reduced engine power light
should come on briey as the engine
is started. If it does not come on have
the vehicle serviced by your dealer/
retailer.
This light, along with the service
engine soon light displays when a
noticeable reduction in the vehicle’s
performance occurs. Stop the vehicle
and turn off the ignition. Wait for
10 seconds and restart the vehicle.
This might correct the condition.The vehicle can be driven at a
reduced speed when the reduced
engine power light is on but
acceleration and speed might be
reduced. The performance could
be reduced until the next time the
vehicle is driven. If this light stays on,
see your dealer/retailer as soon as
possible for diagnosis and repair.Highbeam On Light
The highbeam on light comes on
when the high-beam headlamps are
in use.
SeeHeadlamp High/Low-Beam
Changer on page 3-7for more
information.
Daytime Running Lamps
(DRL) Indicator Light
This light turns on whenever the
Daytime Running Lamps are on.
SeeDaytime Running Lamps (DRL)
on page 3-13for more information.
Instrument Panel 3-39
ProCarManuals.com

Low Washer Fluid
Warning Light
The low washer uid warning light
comes on when the windshield
washer uid is low. SeeWindshield
Washer Fluid on page 5-27for
more information.
All-Wheel Drive Disabled
Light
This light comes on when there
is a malfunction in the All-Wheel
Drive (AWD) system.This light ashes when the AWD
system is temporarily disabled.
For more information seeAll-Wheel
Drive (AWD) System on page 4-9.
Gate Ajar Light
If the gate ajar light comes on,
the liftgate is not completely closed.
Driving with the liftgate open can
cause carbon monoxide (CO) to
enter the vehicle.
SeeEngine Exhaust on page 2-28
for more information.
Door Ajar Light
The door ajar light comes on when a
door is open. Before driving, check
that all doors are properly closed.
Service Vehicle Soon
Light
The service vehicle soon light
comes on if a condition exists
that may require the vehicle to
be taken in for service.
If the light comes on, take the
vehicle to your dealer/retailer for
service as soon as possible.
3-40 Instrument Panel
ProCarManuals.com

Fuel Gage
When the ignition is on, the fuel
gage indicates how much fuel is
left in the tank.
When the indicator nears empty,
the low fuel light comes on. There is
still a little fuel left, but the fuel tank
should be relled soon. SeeLow
Fuel Warning Light on page 3-41
for more information.
An arrow on the fuel gage indicates
the side of the vehicle the fuel
door is on.Here are four things that some
owners ask about. None of these
means the fuel gage is not working
properly:
At the service station, the fuel
pump shuts off before the
gage reads full.
It takes a little more or less fuel
to ll up than the gage indicated.
For example, the gage may have
indicated the tank was half full,
but it actually took a little more or
less than half the tank’s capacity
to ll the tank.
The gage moves a little while
turning a corner or speeding up.
The gage takes a few seconds to
stabilize after the ignition is turned
on, but it goes back to empty
when the ignition is turned off.
For fuel tank capacity, see
Capacities and Specifications
on page 5-86.
Low Fuel Warning Light
The low fuel warning light, below
the fuel gage, comes on briey when
the engine is started.
This light also comes on when the
fuel tank is low on fuel. When fuel is
added, the light should go off. If it
does not, have the vehicle serviced. United StatesCanada
Instrument Panel 3-41
ProCarManuals.com

Driver Information
Center (DIC)
Your vehicle has a Driver
Information Center (DIC).
All information appears in the DIC
display located in the instrument
panel cluster.
The DIC comes on when the
ignition is on. After a short delay,
the DIC displays the information
that was last displayed before
the engine was turned off.
The DIC displays trip, fuel, and
vehicle system information, and
warning messages if a system
problem is detected.
The DIC also displays the compass
direction, outside air temperature,
and shift position indicator at thetop of the DIC display. If there is
a problem with the system that
controls the temperature display,
the numbers will be replaced with
dashes. If this occurs, have the
vehicle serviced by your dealer/
retailer. If an abnormal temperature
reading is displayed for an extended
period of time, consult your
dealer/retailer. Under certain
circumstances, especially when
the engine is idling, a delay updating
the temperature display is normal.
SeeDIC Compass on page 3-47
andAutomatic Transmission
Operation (Uplevel) on page 2-19or
Automatic Transmission Operation
(Base) on page 2-22for more
information.
DIC Operation and
Displays
The DIC has different displays which
can be accessed by pressing the DIC
buttons located on the instrument
panel, below the headlamp switch.
The DIC displays trip, fuel, and
vehicle system information, and
warning messages if a system
problem is detected.
The DIC also allows some features
to be customized. SeeDIC Vehicle
Customization on page 3-57for more
information.
3-42 Instrument Panel
ProCarManuals.com

DIC Buttons
The buttons are the trip/fuel,
vehicle information, customization,
and set/reset buttons. The button
functions are detailed in the
following pages.
3(Trip/Fuel):Press this
button to display the odometer,
trip odometer, fuel range, average
economy, fuel used, and elapsed
time. Some vehicles also display
instantaneous economy. The
compass and outside temperature
will also be shown in the display.
The temperature will be shown
in °F or °C depending on the units
selected.
T(Vehicle Information):Press
this button to display the oil life,
units, tire pressure readings
for vehicles with the Tire Pressure
Monitor System (TPMS), Remote
Keyless Entry (RKE) transmitter
programming, compass zone
setting, compass recalibration on
vehicles with this feature, coolant
temperature, and battery voltage.
U(Customization):Press this
button to customize the feature
settings on your vehicle. SeeDIC
Vehicle Customization on page 3-57
for more information.
V(Set/Reset):Press this button
to set or reset certain functions
and to turn off or acknowledge
messages on the DIC.
Trip/Fuel Menu Items
3(Trip/Fuel):Press this button
to scroll through the following
menu items:
Odometer
Press the trip/fuel button until
ODOMETER displays. This display
shows the distance the vehicle
has been driven in either miles (mi)
or kilometers (km). Pressing the
trip odometer reset stem will
also display the odometer.
To switch between English and
metric measurements, see “Units”
later in this section.
Instrument Panel 3-43
ProCarManuals.com

Trip Odometer
Press the trip/fuel button until
TRIP A or TRIP B displays.
This display shows the current
distance traveled in either miles (mi)
or kilometers (km) since the last
reset for the trip odometer. Pressing
the trip odometer reset stem will
also display the trip odometer.
Each trip odometer can be reset
to zero separately by pressing
the set/reset button while the trip
odometer is displayed. You can
also reset the trip odometer while
it is displayed by pressing and
holding the trip odometer reset stem.
Fuel Range
Press the trip/fuel button until
FUEL RANGE displays. This
display shows the approximate
number of remaining miles (mi)
or kilometers (km) the vehicle
can be driven without refueling.
The display will show LOW if
the fuel level is low.The fuel range estimate is based
on an average of the vehicle’s fuel
economy over recent driving history
and the amount of fuel remaining
in the fuel tank. This estimate will
change if driving conditions change.
For example, if driving in traffic and
making frequent stops, this display
may read one number, but if the
vehicle is driven on a freeway, the
number may change even though
the same amount of fuel is in the fuel
tank. This is because different driving
conditions produce different fuel
economies. Generally, freeway
driving produces better fuel economy
than city driving. Fuel range cannot
be reset.
If the vehicle is low on fuel, the
FUEL LEVEL LOW message will be
displayed. See “FUEL LEVEL LOW”
underDIC Warnings and Messages
on page 3-49.Average Fuel Economy
Press the trip/fuel button until
AVERAGE FUEL ECONOMY
displays. This display shows
the approximate average miles
per gallon (mpg) or liters per
100 kilometers (L/100 km). This
number is calculated based on the
number of mpg (L/100 km) recorded
since the last time this menu item
was reset. To reset the AVERAGE
FUEL ECONOMY, press and hold
the set/reset button. The display will
show zero.
Fuel Used
Press the trip/fuel button until
FUEL USED displays. This display
shows the number of gallons (gal) or
liters (L) of fuel used since the last
reset of this menu item. To reset
the fuel used information, press
and hold the set/reset button while
FUEL USED is displayed.
3-44 Instrument Panel
ProCarManuals.com