climate control SATURN VUE HYBRID 2008 User Guide

Climate Controls
Automatic Climate Control System
The heating, cooling, and ventilation for the vehicle can
be controlled with this system.
Climate Control Inuence on Hybrid
Operation and Fuel Economy
To maximize your fuel economy, use the following
settings:
Set the fan knob to AUTO.
Set the air delivery knob to AUTO.
Select an air temperature setting near 75°F (23°C).
Select the Hybrid A/C button, if A/C is required.Avoid using these settings that may lead to fewer auto
stops and to higher fuel consumption:
Manual fan speed operation.
Defrost mode. Only use this setting to clear the
windows.
Extreme cold or hot air temperature settings, such
as 60°F (16°C) or 90°F (32°C).
Normal air conditioning mode, if A/C is required.
Automatic Operation
This climate control system automatically maintains the
desired temperature inside the vehicle.
Do not cover the sensor located on the top of the
instrument panel near the windshield or the sensor grille
below the climate control faceplate. These two sensors
help regulate the inside air temperature.
AUTO (Automatic Fan):Turn the fan knob to AUTO
for the system to automatically adjust the fan speed
to reach the desired inside temperature.
Temperature Control:Select the desired air
temperature between 60-90°F (16-32°C). Typically,
the best setting is near 75°F (23°C). Choosing the
coldest or warmest temperature setting does not
cause the system to heat or cool any faster.
3-18
ProCarManuals.com

AUTO (Automatic Air Delivery Mode):Turn the
air delivery mode knob to AUTO for the system to
automatically control the direction of the airow to help
reach the desired inside temperature.
The system automatically controls the air inlet to supply
the outside air or recirculated inside air needed to cool
the vehicle faster. The indicator light on the recirculation
button will be lit whenever the system changes to
recirculation. Press the recirculation button to change
to outside air. However, the recirculation mode may
turn back on automatically.
In cold weather, if the fan and air delivery modes are
in automatic, the system starts at lower fan speeds to
avoid directing cold air into the vehicle until warmer air is
available. The climate control system directs air to the
oor, but may automatically change modes as the vehicle
warms up to maintain the chosen temperature setting.
The length of time needed to warm the interior depends
on the outside temperature and inside temperature of
the vehicle.Manual Operation
It is best to use the automatic settings to maximize fuel
economy.
To change the current fan speed, turn the left knob.
A(Fan):Turn the left knob clockwise to increase
the fan speed or counterclockwise to decrease the
fan speed. To turn the fan off, turn the left knob to
the
9position. In any setting other than off, the fan
runs continuously with the ignition on. The fan must be
turned on to run the air conditioning compressor. There
will be some airow noticeable from the various outlets
when driving, even with the fan in the off position.
This is to ensure some fresh air is always available
in the vehicle. To turn off the air completely, turn the
fan to
9and select the recirculation button.
Temperature Control:Select the desired cabin air
temperature between 60-90°F (16-32°C). Typically,
the best setting is near 75°F (23°C). Choosing the
coldest or warmest temperature setting does not
cause the system to heat or cool any faster.
3-19
ProCarManuals.com

To change the current air delivery mode, use the right
knob to select one of the following:
H(Vent):This mode directs air to the instrument
panel outlets.
)(Bi-Level):This mode divides the air between the
instrument panel outlets and the oor outlets.
6(Floor):This mode directs most of the air to the
oor outlets with some air directed to the windshield.
When this mode is selected, the system turns the
recirculation mode off. Recirculation mode cannot be
selected while in oor mode. This is to help prevent
window fogging.
The right knob can also be used to select defog or
defrost mode. See “Defogging and Defrosting” later in
this section.
#(Normal Air Conditioning):Press this button to
turn the air conditioning system on or off. When this
button is pressed, an indicator light comes on to show
that the air conditioning is activated. Normal Air
Conditioning (A/C) can be selected in any mode as long
as the fan is on and the outside air temperature is above
freezing. Normal A/C cannot be selected at the same
time as Hybrid Air Conditioning (A/C). A ashing indicator
light indicates that the air conditioning compressor is
currently not available.When Normal A/C is selected, the climate control system
will prevent all automatic engine start/stop operations.
This will ensure the cabin comfort is maintained. See “Air
Conditioning and Automatic Engine Start/Stop” later in
this section.
N(Hybrid Air Conditioning):Press this button to
turn the Hybrid A/C system on or off. When this button is
pressed, an indicator light comes on to show that the
Hybrid A/C is activated. Hybrid A/C can be selected in
any mode, except defrost as long as the fan is on and the
outside air temperature is above freezing. Hybrid A/C
cannot be selected at the same time as the normal air
conditioning. A ashing indicator light indicates the air
conditioning compressor is not available.
The Hybrid A/C works to balance fuel economy and air
conditioning comfort. When Hybrid A/C is used in warm
weather, the vehicle gets better fuel economy by allowing
more frequent start/stops. For additional cooling, select
Normal A/C. See “Air Conditioning and Automatic Engine
Start/Stop” later in this section.
3-20
ProCarManuals.com

@(Recirculation):Press this button to toggle
between recirculate and outside air modes. The indicator
light turns on when the recirculate mode is selected.
This mode can be used to prevent outside air and odors
from entering the vehicle or to help cool the air inside
the vehicle more quickly. Avoid using the recirculation
mode during high periods of humidity and cool outside
temperatures since this may result in increased window
fogging. If window fogging is experienced, select the
defrost mode.
Recirculation mode is not available in oor, defog or
defrost modes. If the button is selected in these modes,
the indicator will ash. This helps prevent window fogging
and moisture building up inside the vehicle.
Defogging and Defrosting
Fog on the inside of windows is a result of high humidity
(moisture) condensing on the cool window glass. This
can be minimized if the climate control system is used
properly. There are two modes to clear fog or frost from
the windshield and side windows. Use the defog mode
to clear the windows of fog or moisture and warm the
passengers. Use the defrost mode to remove fog or frost
from the windshield more quickly. For best results, clear
all snow and ice from the windshield before defrosting.Manually turn the right knob to select the defog or
defrost mode.
-(Defog):This mode directs air to the windshield,
side window outlets and oor outlets. When this mode is
selected, the system turns the recirculation mode off and
runs the air conditioning compressor unless the outside
air is at or below freezing. The recirculation mode cannot
be selected while in defog mode. This helps prevent
window fogging and moisture building up inside the
vehicle.
0(Defrost):This mode directs most of the air to the
windshield, with some air directed to the side window
outlets and the oor outlets. When this mode is selected,
the system turns the recirculation mode off automatically
and runs the air conditioning compressor unless the
outside air is at or below freezing. The recirculation mode
cannot be selected while in defrost mode. This helps
prevent window fogging and moisture building up inside
the vehicle. In this mode, the climate control system
prevents all automatic engine start/stop operations.
This ensures the best defrost performance.
3-21
ProCarManuals.com

Rear Window Defogger
The rear window defogger uses a warming grid to
remove fog from the rear window.
The rear window defogger will only work when the
ignition is in ON/RUN.
<(Rear Window Defogger):Press this button to
turn the rear window defogger on or off. An indicator
light on the button comes on to show that the rear
window defogger is activated.
The rear window defogger stays on for about 10 minutes
if the vehicle remains at slower vehicle speeds or until
the button is pressed, or unless the ignition is turned
to ACC/ACCESSORY or LOCK/OFF. If turned on again,
the defogger only runs for about ve minutes before
turning off again. At higher vehicle speeds, the defogger
may stay on continuously. The defogger can always
be turned off by pressing the button again or by turning
off the ignition.
Notice:Do not use anything sharp on the inside
of the rear window. If you do, you could cut or
damage the warming grid, and the repairs would
not be covered by the vehicle warranty. Do not
attach a temporary vehicle license, tape, a decal
or anything similar to the defogger grid.
Air Conditioning and Engine Start/Stop
On hot days, use the automatic fan and automatic air
delivery mode settings and the vehicle will reach the
desired temperature more quickly. The desired fan and
air delivery mode settings can still be adjusted manually.
Open the windows to let the hot inside air escape, then
close them. This helps reduce the time it takes for the
vehicle to cool down and helps the system to operate
more efficiently.
When either the Normal A/C or Hybrid A/C modes are
active, the air conditioning system removes moisture
from the air, so a small amount of water may drip under
the vehicle while idling or after turning off the engine.
This is normal.
The use of Normal A/C causes the engine to keep
running while the vehicle is at a complete stop to allow
the climate control system to continue cooling.
The use of Hybrid A/C allows automatic engine start/
stop operations while the vehicle is at a complete stop.
The air conditioning compressor can not run when
the engine is not running, resulting in reduced cooling
performance. The climate control system may keep the
engine running or restart the engine during a stop to
continue cooling. Selecting the Normal A/C button forces
the engine and air conditioning compressor to restart
automatically. For more information about Engine
Start/Stop operation, seeStarting the Engine
(Automatic Engine Start/Stop) on page 2-18.
3-22
ProCarManuals.com

Compass Calibration
The compass can be manually calibrated. Only calibrate
the compass in a magnetically clean and safe location,
such as an open parking lot, where driving the vehicle
in circles is not a danger. It is suggested to calibrate
away from tall buildings, utility wires, manhole covers,
or other industrial structures, if possible.
If CAL should ever appear in the DIC display, the
compass should be calibrated.
If the DIC display does not show a heading, for
example, N for North, or the heading does not change
after making turns, there may be a strong magnetic eld
interfering with the compass. Such interference may be
caused by a magnetic CB or cell phone antenna mount, a
magnetic emergency light, magnetic note pad holder, or
any other magnetic item. Turn off the vehicle, move the
magnetic item, then turn on the vehicle and calibrate the
compass.To calibrate the compass, use the following procedure:Compass Calibration Procedure
1. Before calibrating the compass, make sure the
compass is set to the variance zone in which
the vehicle is located. See “Compass Variance
(Zone) Procedure” earlier in this section.
Do not operate any switches such as window,
sunroof, climate controls, seats, etc. during
the calibration procedure.
2. Press the reset stem until HOLD STEM TO
CALIBRATE COMPASS displays.
3. Press and hold the reset stem to start the compass
calibration.
4. The DIC will display CALIBRATING COMPASS:
TURN IN CIRCLES. Drive the vehicle in tight
circles at less than 5 mph (8 km/h) to complete
the calibration. The DIC will display COMPASS
CALIBRATION COMPLETE for a few seconds
when the calibration is complete. The DIC display
will then return to HOLD STEM TO CALIBRATE
COMPASS.
3-49
ProCarManuals.com

Treadwear
The treadwear grade is a comparative rating
based on the wear rate of the tire when tested
under controlled conditions on a specied
government test course. For example, a tire graded
150 would wear one and a half (1.5) times as well
on the government course as a tire graded 100.
The relative performance of tires depends upon the
actual conditions of their use, however, and may
depart signicantly from the norm due to variations
in driving habits, service practices, and differences
in road characteristics and climate.
Traction – AA, A, B, C
The traction grades, from highest to lowest, are AA,
A, B, and C. Those grades represent the tire’s
ability to stop on wet pavement as measured under
controlled conditions on specied government test
surfaces of asphalt and concrete. A tire marked C
may have poor traction performance.
Warning
:The traction grade assigned to this
tire is based on straight-ahead braking traction
tests, and does not include acceleration,
cornering, hydroplaning, or peak traction
characteristics.
Temperature – A, B, C
The temperature grades are A (the highest), B,
and C, representing the tire’s resistance to the
generation of heat and its ability to dissipate heat
when tested under controlled conditions on a
specied indoor laboratory test wheel. Sustained
high temperature can cause the material of the
tire to degenerate and reduce tire life, and
excessive temperature can lead to sudden tire
failure. The grade C corresponds to a level of
performance which all passenger car tires must
meet under the Federal Motor Vehicle Safety
Standard No. 109. Grades B and A represent
higher levels of performance on the laboratory
test wheel than the minimum required by law.
Warning
:The temperature grade for this
tire is established for a tire that is properly
inated and not overloaded. Excessive speed,
underination, or excessive loading, either
separately or in combination, can cause heat
buildup and possible tire failure.
5-63
ProCarManuals.com

The sealant cannot seal sidewall damage, large
punctures, or a tire that has become unseated from
the wheel. SeeRoadside Assistance Program on
page 7-6.
Do not remove any objects that have penetrated
the tire.
3. Place the tire sealant and compressor kit on the
ground and unwrap the sealant/air hose (G) from
the side of the compressor.
4. Remove the valve stem cap from the at tire by
turning it counterclockwise.
5. Attach the sealant/air hose (G) onto the tire valve
stem. Turn it clockwise until it is tight.
Make sure the sealant and compressor kit on/off
switch (D) is in the O (off) position.
6. Remove the air compressor accessory plug (C)
from the unit.
7. Plug the air compressor accessory plug (C) into an
accessory power outlet in the vehicle. SeeAccessory
Power Outlet(s) on page 3-17for more information.
Do not slam door or close window on the
compressor accessory plug cord.
{CAUTION:
Idling the engine in a closed-in place or with
the climate control system off can cause
deadly carbon monoxide (CO). SeeEngine
Exhaust on page 2-29.
8. Start the vehicle. SeeStarting the Engine
(Automatic Engine Start/Stop) on page 2-18
for more information. The vehicle must be
running while using the air compressor.
{CAUTION:
Overination could cause the tire to rupture,
and you or others could be injured. Be sure to
read the inator instructions, and inate the
tire to its recommended pressure. Do not
exceed 36 psi (248 kPa).
5-72
ProCarManuals.com

4. Push the air only hose (F) onto the tire valve stem
and push the lever down to secure in place.
5. Remove the air compressor accessory plug (C)
from the unit.
6. Plug the air compressor accessory plug into an
accessory power outlet in the vehicle. SeeAccessory
Power Outlet(s) on page 3-17for more information.
Do not slam the door or close the window on the
compressor accessory plug cord.
{CAUTION:
Idling the engine in a closed-in place or with
the climate control system off can cause
deadly carbon monoxide (CO). SeeEngine
Exhaust on page 2-29.
7. Start the vehicle. SeeStarting the Engine
(Automatic Engine Start/Stop) on page 2-18.
The vehicle must be running while using the
air compressor.
{CAUTION:
Overination could cause the tire to rupture,
and you or others could be injured. Be sure to
read the inator instructions, and inate the
tire to its recommended pressure. Do not
exceed 36 psi (248 kPa).
8. Push the On/Off switch (D) to the I (on) position.
The tire sealant and compressor kit will inate the
tire with air only.
9. Inate the tire to the recommended ination
pressure using the air pressure gage (E) on the
top of the unit. SeeInflation - Tire Pressure
on page 5-52.
The pressure gage reading is slightly high while the
compressor is on. Turn the compressor off to get
an accurate pressure reading. The compressor may
be turned on and off until the correct pressure is
reached.
10. Turn off the air compressor by pushing the On/Off
switch (D) to the O (off) position.
Be careful while handling the tire sealant and
compressor kit as they could be hot after usage.
5-76
ProCarManuals.com

Audio System(s).............................................3-62
Auto Stop Mode.............................................3-42
Automatic Climate Control System.....................3-18
Automatic Headlamp System............................3-15
Automatic Transmission
Fluid..........................................................5-20
Operation...................................................2-23
B
Battery..........................................................5-33
Run-Down Protection...................................3-17
Brake
Emergencies................................................ 4-6
Brakes..........................................................5-30
Regenerative Braking...................................2-26
System Warning Light..................................3-32
Braking........................................................... 4-5
Braking in Emergencies..................................... 4-6
Break-In, New Vehicle.....................................2-16
Bulb Replacement...........................................5-41
Front Turn Signal and Parking Lamps.............5-43
Halogen Bulbs............................................5-41
Headlamp Aiming........................................5-39
Headlamps.................................................5-42
License Plate Lamps....................................5-45Bulb Replacement (cont.)
Replacement Bulbs......................................5-45
Taillamps, Turn Signal, Stoplamps and
Back-up Lamps........................................5-44
Buying New Tires...........................................5-60
C
Calibration.....................................................3-48
California Fuel.................................................. 5-6
California Perchlorate Materials Requirements....... 5-4
California Proposition 65 Warning....................... 5-4
Canadian Owners................................................ ii
Capacities and Specications............................5-98
Carbon Monoxide...........................2-29, 4-17, 4-31
Care of
Safety Belts................................................5-81
Cargo Cover..................................................2-43
Cargo Management System.............................2-44
Cargo Tie Downs............................................2-43
CD, MP3 .......................................................3-70
Center Console Storage Area...........................2-42
Chains, Tire...................................................5-66
Charge/Assist Gage........................................3-43
Charging System Light....................................3-32
Check
Engine Light...............................................3-36
2
ProCarManuals.com