lock SATURN VUE HYBRID 2008 Manual Online

Operating electronic devices or being near facilities
using radio wave frequencies similar to the TPMS
could cause the TPMS sensors to malfunction.
If the TPMS is not functioning it cannot detect or
signal a low tire condition. See your dealer/retailer for
service if the TPMS malfunction light and DIC message
comes on and stays on.
TPMS Sensor Matching Process
Each TPMS sensor has a unique identication code.
Any time you replace one or more of the TPMS sensors
or rotate the vehicle’s tires, the identication codes
will need to be matched to the new tire/wheel position.
The sensors are matched, to the tire/wheel positions,
in the following order: driver side front tire, passenger
side front tire, passenger side rear tire, and driver
side rear tire using a TPMS diagnostic tool. See your
dealer/retailer for service.
The TPMS sensors can also be matched to each
tire/wheel position by increasing or decreasing the tire’s
air pressure. When increasing the tire’s pressure, do
not exceed the maximum ination pressure indicated on
the tire’s sidewall. To decrease the tire’s air-pressure
use the pointed end of the valve cap, a pencil-style
air pressure gage, or a key.You have two minutes to match each tire and wheel
position. If it takes longer than two minutes to match
any tire and wheel position, the matching process stops
and you will need to start over.
The TPMS matching process is outlined below:
1. Set the parking brake.
2. Turn the ignition switch to ON/RUN with the
engine off.
3. Press and hold the RKE transmitter’s lock
and unlock buttons at the same time, for about
three seconds. The horn sounds twice to indicate
the receiver is ready for the sensor matching process
to begin. The TIRE LEARNING ACTIVE message
displays on the DIC screen.
4. Start with the driver side front tire. The driver side
turn signal lamp comes on.
5. Remove the valve cap from the tire’s valve stem.
Activate the TPMS sensor by increasing or
decreasing the tire’s air pressure for ve seconds,
or until a horn chirp sounds. The horn chirp,
which may take up to 30 seconds to sound,
conrms that the sensor identication code
has been matched to the tire/wheel position.
6. Proceed to the passenger side front tire.
The passenger side front turn signal lamp
comes on. Repeat the procedure in Step 5.
5-57
ProCarManuals.com

7. Proceed to the passenger side rear tire.
The passenger side rear turn signal lamp
comes on. Repeat the procedure in Step 5.
8. Proceed to the driver side rear tire. The driver
side rear turn signal lamp comes on. Repeat the
procedure in Step 5. The horn sounds two times to
indicate the sensor identication code has been
matched to the driver side rear tire, and the TPMS
sensor matching process is no longer active. The
TIRE LEARNING ACTIVE message on the DIC
display screen goes off.
9. Turn the ignition switch to LOCK/OFF.
10. Set all four tires to the recommended air pressure
level as indicated on the Tire and Loading
Information label.
11. Put the valve caps back on the valve stems.
Tire Inspection and Rotation
We recommend that you regularly inspect your
vehicle’s tires for signs of wear or damage.
SeeWhen It Is Time for New Tires on page 5-59
for more information.
Tires should be rotated every 5,000 to 8,000 miles
(8 000 to 13 000 km). SeeScheduled Maintenance
on page 6-4.The purpose of a regular tire rotation is to achieve
a uniform wear for all tires on the vehicle. This will
ensure that your vehicle continues to perform most
like it did when the tires were new.
Any time you notice unusual wear, rotate your tires
as soon as possible and check wheel alignment.
Also check for damaged tires or wheels. SeeWhen
It Is Time for New Tires on page 5-59andWheel
Replacement on page 5-64for more information.
When rotating the vehicle’s tires, always use the
correct rotation pattern shown here.
After the tires have been rotated, adjust the front
and rear ination pressures as shown on the Tire
and Loading Information label. SeeInflation - Tire
Pressure on page 5-52andLoading Your Vehicle
on page 4-22.
5-58
ProCarManuals.com

Different Size Tires and Wheels
If you add wheels or tires that are a different size than
your original equipment wheels and tires, this may
affect the way your vehicle performs, including its
braking, ride and handling characteristics, stability,
and resistance to rollover. Additionally, if your vehicle
has electronic systems such as, anti-lock brakes,
rollover airbags, traction control, and stability control,
the performance of these systems can be affected.
{CAUTION:
If you add different sized wheels, your
vehicle may not provide an acceptable
level of performance and safety if tires not
recommended for those wheels are selected.
You may increase the chance that you will
crash and suffer serious injury. Only use Saturn
specic wheel and tire systems developed for
your vehicle, and have them properly installed
by a Saturn certied technician.
SeeBuying New Tires on page 5-60andAccessories
and Modifications on page 5-3for additional information.
Uniform Tire Quality Grading
Quality grades can be found where applicable
on the tire sidewall between tread shoulder
and maximum section width. For example:
Treadwear 200 Traction AA
Temperature A
The following information relates to the system
developed by the United States National Highway
Traffic Safety Administration (NHTSA), which
grades tires by treadwear, traction, and
temperature performance. This applies only to
vehicles sold in the United States. The grades are
molded on the sidewalls of most passenger car
tires. The Uniform Tire Quality Grading (UTQG)
system does not apply to deep tread, winter-type
snow tires, space-saver, or temporary use spare
tires, tires with nominal rim diameters of
10 to 12 inches (25 to 30 cm), or to some
limited-production tires.
While the tires available on General Motors
passenger cars and light trucks may vary with
respect to these grades, they must also conform
to federal safety requirements and additional
General Motors Tire Performance Criteria (TPC)
standards.
5-62
ProCarManuals.com

4. Open the oor cargo organizer locks, located on
the top left and right corners of the organizer,
by pushing inward on them.
5. Remove the load oor cargo organizer.6. Remove the foam retainer bolt (B) holding down the
foam container.
7. Remove the foam container (C).
8. Remove the sealant and compressor kit (A) from its
foam container.
5-70
ProCarManuals.com

The sealant cannot seal sidewall damage, large
punctures, or a tire that has become unseated from
the wheel. SeeRoadside Assistance Program on
page 7-6.
Do not remove any objects that have penetrated
the tire.
3. Place the tire sealant and compressor kit on the
ground and unwrap the sealant/air hose (G) from
the side of the compressor.
4. Remove the valve stem cap from the at tire by
turning it counterclockwise.
5. Attach the sealant/air hose (G) onto the tire valve
stem. Turn it clockwise until it is tight.
Make sure the sealant and compressor kit on/off
switch (D) is in the O (off) position.
6. Remove the air compressor accessory plug (C)
from the unit.
7. Plug the air compressor accessory plug (C) into an
accessory power outlet in the vehicle. SeeAccessory
Power Outlet(s) on page 3-17for more information.
Do not slam door or close window on the
compressor accessory plug cord.
{CAUTION:
Idling the engine in a closed-in place or with
the climate control system off can cause
deadly carbon monoxide (CO). SeeEngine
Exhaust on page 2-29.
8. Start the vehicle. SeeStarting the Engine
(Automatic Engine Start/Stop) on page 2-18
for more information. The vehicle must be
running while using the air compressor.
{CAUTION:
Overination could cause the tire to rupture,
and you or others could be injured. Be sure to
read the inator instructions, and inate the
tire to its recommended pressure. Do not
exceed 36 psi (248 kPa).
5-72
ProCarManuals.com

9. Push the On/Off switch (D) to the I (on) position.
The tire sealant and compressor kit will inject
sealant and air into the tire.
The pressure gage (E) will initially show a high
pressure while the compressor pushes the sealant
into the tire. Once the sealant is completely
dispersed into the tire, the pressure will quickly drop
and start to rise again as the tire inates with air only.
10. Inate the tire to the recommended ination
pressure using the air pressure gage (E) on the top
of the unit. The recommended ination pressure
can be found on the Tire and Loading Information
label. SeeInflation - Tire Pressure on page 5-52.
The pressure gage reading is slightly high while the
compressor is on. Turn the compressor off to get
an accurate reading. The compressor may be turned
on and off until the correct pressure is reached.
Notice:If the recommended pressure cannot be
reached after 15 minutes, the vehicle should not
be driven farther. Damage to the tire is severe and
the sealant will not be effective. Remove the air
compressor plug from the accessory power outlet
and unscrew the inating hose from the tire
valve. SeeRoadside Assistance Program on
page 7-6for more information.11. Turn the compressor off by pushing the On/Off
switch (D) to the O (off) position.
Steps 12 through 20 must be done immediately
after Step 11.
The tire is not sealed and will continue to leak
air until the vehicle is driven and the sealant
is distributed in the tire.
Be careful while handling the tire sealant and
compressor kit as they could be hot after usage.
12. Unplug the air compressor accessory plug (C) from
the accessory power outlet in the vehicle.
13. Disconnect the sealant/air hose (G) from the tire
valve stem by turning it counterclockwise and
replace the tire valve stem cap.
14. Wrap the sealant/air hose (G) around the air
compressor channel to stow it in its original location.
15. Stow the air compressor accessory plug (C) back
in the air compressor. To do this, wrap the air
compressor accessory plug, snap in the plug, and
then push in the bottom and then the top of the
wrapped air compressor accessory plug.
5-73
ProCarManuals.com

16. If the at tire was
able to inate to the
recommended ination
pressure, remove
the maximum speed
label from the sealant
canister (B).
17. Place it in a highly visible location such as the
inside of the upper left corner of the windshield
or to the face of the radio/clock.
The maximum speed label reminds you to drive
cautiously and not to exceed 55 mph (90 km/h) until
you have the damaged tire inspected and repaired.
{CAUTION:
Storing the tire sealant and compressor
kit or other equipment in the passenger
compartment of the vehicle could cause injury.
In a sudden stop or collision, loose equipment
could strike someone. Store the tire sealant
and compressor kit in its original location.
18. Return the equipment to its original storage location
in your vehicle.
19. Immediately drive the vehicle 5 miles (8 km) to
distribute the sealant evenly in the tire.
5-74
ProCarManuals.com

20. Stop at a safe location and check the tire pressure,
refer to Steps 1 through 8 under “Using the Tire
Sealant and Compressor Kit without Sealant
to Inate an Underinated Tire (Not Punctured)”
later in this section.
If the tire pressure has fallen more then 10 psi
(68 kPa), below the recommended ination pressure,
stop driving the vehicle. The tire is too severely
damaged and the tire sealant and compressor kit
cannot seal the tire. SeeRoadside Assistance
Program on page 7-6for more information.
If the tire pressure has not dropped more than
10 psi (68 kPa) from the recommended ination
pressure, you can inate the tire back up to
the recommended ination pressure.
21. Wipe off any sealant from the wheel, tire and
vehicle.
22. Dispose of the sealant canister (B) and sealant/air
hose (G) assembly at a local dealer/retailer or in
accordance with your local state codes and
practices.
23. After temporarily sealing a tire with the tire
sealant and compressor kit, take your vehicle
to an authorized dealer/retailer to have the tire
inspected and repaired or replaced.Using the Air Compressor without
Sealant to Inate an Underinated Tire
(Not Punctured)
To use the air compressor to inate a tire with air only
and not sealant:
1. Unlock the air only hose (F) from the sealant
canister (B) by pulling up on the lever.
2. Pull the air only hose (F) from the sealant
canister (B).
3. Remove the tire valve stem cap by turning it
counterclockwise.
5-75
ProCarManuals.com

11. Unplug the air compressor accessory plug from the
accessory power outlet in the vehicle.
12. Unlock the air only hose (F) from the tire valve stem
by pulling the lever up.
13. Disconnect the air only hose (F) from the tire valve
stem and replace the tire valve stem cap.
14. Wrap the air only hose (F) around the side of the
air compressor channel to stow it back in its
original location.
15. Stow the air compressor accessory plug back in the
air compressor. To do this, wrap the air compressor
accessory plug, snap in the plug, and then push
in the bottom and then the top of the wrapped
air compressor accessory plug.
16. Return the equipment to its original storage location
of your vehicle.
{CAUTION:
Storing the tire sealant and compressor
kit or other equipment in the passenger
compartment of the vehicle could cause injury.
In a sudden stop or collision, loose equipment
could strike someone. Store the tire sealant
and compressor kit in its original location.
5-77
ProCarManuals.com

Removal and Installation of the Sealant
Canister
To remove the sealant canister, do the following:
1. Unlock the air only hose from the sealant canister
by pulling the lever up.
2. Unwrap the sealant/air hose from the compressor.3. Turn the sealant canister so the inator lling hose
is aligned with the slot in the compressor.
4. Lift the sealant canister from the compressor and
replace with a new sealant canister. See your
dealer/retailer for more information.
5-78
ProCarManuals.com