reset SATURN VUE HYBRID 2008 Owners Manual

Speedometer and Odometer
The speedometer lets you see your speed in both miles
per hour (mph) and kilometers per hour (km/h).
The odometer shows how far your vehicle has been
driven, in either miles or kilometers.
Your vehicle has a tamper-resistant odometer. If your
vehicle needs a new odometer installed, the new one will
be set to the mileage total of the old odometer. If this is
not possible, it will be set at zero and a label must be
put on the driver’s door to show the old mileage reading
when the new odometer was installed. If the mileage
is unknown, the label should then indicate “previous
mileage unknown”.
Trip Odometer
Your trip odometer is located on the instrument panel
and shows how far your vehicle has been driven since the
trip odometer was last reset. To reset the trip odometer
to zero, press and hold the trip/reset button on the
speedometer for about two seconds. Press the trip/reset
button to switch between the trip odometer and odometer.
Tachometer
The tachometer
displays the engine
speed in revolutions
per minute (rpm).
The auto stop indicator is located at the bottom of the
tachometer. For more information seeAuto Stop Mode
on page 3-42. U.S. shown,
Canada similar
3-27
ProCarManuals.com

If the light comes on while driving, a chime will sound.
Pull off the road and stop. The pedal might be harder to
push or go closer to the oor. It might also take longer
to stop. If the light is still on, have the vehicle towed
for service. SeeTowing Your Vehicle on page 4-28.
{CAUTION:
Your brake system may not be working
properly if the brake system warning light is
on. Driving with the brake system warning light
on can lead to an accident. If the light is still
on after you have pulled off the road and
stopped carefully, have the vehicle towed
for service.
Anti-lock Brake System (ABS)
Warning Light
For vehicles with
the Antilock Brake
System (ABS), this light
comes on briey when
the engine is started.
That is normal. If the light does not come on then, have
it xed so it will be ready to warn you if there is a problem.
If the ABS light stays on, turn the ignition off, if the light
comes on when you are driving, stop as soon as it is
safely possible and turn the ignition off. Then start the
engine again to reset the system. If the ABS light still
stays on, or comes on again while you are driving,
your vehicle needs service. If the regular brake system
warning light is not on, your vehicle still has brakes, but
not antilock brakes. If the regular brake system warning
light is also on, your vehicle does not have antilock
brakes and there is a problem with the regular brakes.
SeeBrake System Warning Light on page 3-32.
For vehicles with a Driver Information Center (DIC),
seeDIC Warnings and Messages on page 3-50for
all brake related DIC messages.
3-33
ProCarManuals.com

{CAUTION:
Do not keep driving if the oil pressure is low.
If you do, your engine can become so hot that
it catches re. You or others could be burned.
Check your oil as soon as possible and have
your vehicle serviced.
Notice:Lack of proper engine oil maintenance
may damage the engine. The repairs would not
be covered by your warranty. Always follow
the maintenance schedule in this manual for
changing engine oil.
Change Engine Oil Light
This light means that
service is required for
your vehicle.
SeeScheduled Maintenance on page 6-4andEngine
Oil on page 5-13for more information.
After the engine oil is changed the engine oil life system
needs to be reset in order to turn off this light. SeeEngine
Oil Life System on page 5-16for more information.
3-39
ProCarManuals.com

Charge/Assist Gage
The CHARGE/ASSIST
gage displays the charge
(current) into and out
of the hybrid battery.
While the electric motor is performing an automatic
restart of the engine, or while it is assisting the engine,
as in maximum acceleration, the needle moves to the
ASSIST range, located on the right side of the gage.
The needle moves to the CHARGE range when the
electric motor operates as a generator to perform
regenerative braking, as the vehicle slows down.
SeeRegenerative Braking on page 2-26for more
information. The needle also moves into the CHARGE
range if the hybrid control system identies it is an
efficient time to charge the hybrid battery.If the hybrid battery or other hybrid components are
very hot or cold, the CHARGE and ASSIST functions
may be suspended until the component temperatures
are normal.
Fuel Economy Light
This light comes on when
the vehicle is achieving fuel
economy close to its rated
performance.
Driving habits that improve fuel economy increases the
time that the fuel economy light is on.
To turn the fuel economy light off or on, press the
trip/reset button until the HOLD STEM TO SET ECO
(Economy) DIC message is displayed. Then press and
hold the trip/reset button until off or on is selected.
For more information seeTrip Odometer on page 3-27
andDIC Operation and Displays on page 3-44.
3-43
ProCarManuals.com

Driver Information Center (DIC)
Your vehicle has a Driver Information Center (DIC).
All information appears in the DIC display located in the
instrument panel cluster.
The DIC comes on when the ignition is on. After a short
delay, the DIC displays the information that was last
displayed before the engine was turned off.
The DIC displays trip, fuel, and vehicle system
information, and warning messages if a system problem
is detected.
The DIC also displays the compass direction, outside air
temperature, and shift position indicator at the top of the
DIC display. If there is a problem with the system that
controls the temperature display, the numbers will be
replaced with dashes. If this occurs, have the vehicle
serviced by your dealer/retailer. If an abnormal
temperature reading is displayed for an extended period
of time, consult your dealer/retailer. Under certain
circumstances, especially when the engine is idling,
a delay updating the temperature display is normal.
SeeDIC Compass on page 3-48andAutomatic
Transmission Operation on page 2-23for more
information.
DIC Operation and Displays
The DIC has different displays which can be accessed
by pressing the reset stem located on the instrument
panel cluster. These displays are explained in the
following section. To scroll through the available
functions, press and release the reset stem.
ODOMETER
Press and release the reset stem until ODOMETER
displays. This display shows the distance the vehicle
has been driven in either miles (mi) or kilometers (km).
TRIP
Press and release the reset stem until TRIP displays.
This display shows the current distance traveled in either
miles (mi) or kilometers (km) since the last reset for
the trip odometer.
To reset the trip odometer to zero, press and hold the
reset stem while the trip odometer is displayed.
3-44
ProCarManuals.com

RANGE
Press and release the reset stem until RANGE is
displayed. The RANGE display will only be available
when the vehicle is not in PARK (P).
This display shows the approximate number of
remaining miles (mi) or kilometers (km) the vehicle
can be driven without refueling.
The fuel range estimate is based on an average of
the vehicle’s fuel economy over recent driving history
and the amount of fuel remaining in the fuel tank.
This estimate will change if driving conditions change.
For example, if driving in traffic and making frequent
stops, this display may read one number, but if
the vehicle is driven on a freeway, the number may
change even though the same amount of fuel is in the
fuel tank. This is because different driving conditions
produce different fuel economies. Generally, freeway
driving produces better fuel economy than city driving.
If your vehicle is low on fuel, the FUEL LEVEL LOW
message displays. See “FUEL LEVEL LOW” under
DIC Warnings and Messages on page 3-50for more
information.
INSTANT (Instantaneous) FUEL ECONOMY
Press and release the reset stem INSTANT FUEL
ECONOMY displays. The INSTANT FUEL ECONOMY
display will only be available when the vehicle is not
in PARK (P).
This display shows the current fuel economy at a
particular moment and will change frequently as driving
conditions change. This display shows the instantaneous
fuel economy in miles per gallon (mpg) or liters per
100 kilometers (L/100 km). This display cannot be reset.
AVERAGE FUEL ECONOMY
Press and release the reset stem AVERAGE FUEL
ECONOMY displays. The AVERAGE FUEL ECONOMY
display will only be available when the vehicle is not
in PARK (P).
This display shows the approximate average miles per
gallon (mpg) or liters per 100 kilometers (L/100 km).
This number is calculated based on the number of mpg
(L/100 km) recorded since the last time this display
was reset. To reset this display to zero, press and hold
the reset stem.
3-45
ProCarManuals.com

OIL LIFE
Press and release the reset stem until OIL LIFE
REMAINING displays. The OIL LIFE display will only
be available when the vehicle is in PARK (P). This display
shows an estimate of the oil’s remaining useful life. If OIL
LIFE REMAINING 99% appears on the display, that
means 99% of the current oil life remains. The engine oil
life system will alert you to change the oil on a schedule
consistent with your driving conditions.
When the remaining oil life is low, the CHANGE
ENGINE OIL SOON message will appear on the
display. See “CHANGE ENGINE OIL SOON” under
DIC Warnings and Messages on page 3-50. Change
the oil as soon as possible. SeeEngine Oil on page 5-13.
In addition to the engine oil life system monitoring the
oil life, additional maintenance is recommended in the
Maintenance Schedule in this manual. SeeScheduled
Maintenance on page 6-4for more information.
Remember, reset the OIL LIFE after each oil change.
It will not reset itself. Also, be careful not to reset the OIL
LIFE accidentally at any time other than when the oil
has just been changed. It cannot be reset accurately
until the next oil change. To reset the engine oil
life system, seeEngine Oil Life System on page 5-16.
UNITS
Press and release the reset stem until UNITS displays.
This display selects the units of measurement. Once
in this display, press the reset stem to select ENGLISH
(default) or METRIC.
HOLD STEM TO SET LANGUAGE
Press and release the reset stem until HOLD STEM TO
SET LANGUAGE displays. The HOLD STEM TO SET
LANGUAGE display will only be available when the
vehicle is in PARK (P). This display selects the language
in which the DIC messages will appear. Once in this
display, press the reset stem to select ENGLISH
(default), SPANISH, or FRENCH.
Tire Pressure
The pressure for each tire can be viewed in the DIC.
The tire pressure will be shown in either pounds per
square inch (psi) or kilopascals (kPa). Press and release
the reset stem until the DIC displays FRONT TIRES
LEFT ## PSI (kPa) RIGHT ## PSI (kPa). Press and
release the reset stem again until the DIC displays REAR
TIRES LEFT ## PSI (kPa) RIGHT ## PSI (kPa).
If a low or high tire pressure condition is detected by the
system while driving, a message advising you to check
the pressure in a specic tire will appear in the display.
SeeInflation - Tire Pressure on page 5-52andDIC
Warnings and Messages on page 3-50for more
information.
3-46
ProCarManuals.com

If the tire pressure display shows dashes instead of a
value, there may be a problem with your vehicle. If this
consistently occurs, see your dealer/retailer for service.
HOLD STEM TO RELEARN REMOTE KEY
This display matches Remote Keyless Entry (RKE)
transmitters to your vehicle. To match a transmitter:
1. Put the vehicle in PARK (P).
2. Press and release the reset stem until HOLD STEM
TO RELEARN REMOTE KEY displays.
3. Press and hold the reset stem until REMOTE KEY
LEARNING ACTIVE is displayed.
4. Press and hold the lock and unlock buttons on
the rst transmitter at the same time for about
15 seconds.
A chime will sound indicating that the transmitter
is matched and REMOTE KEY LEARNING
COMPLETE will be displayed.
5. To match additional transmitters at this time, repeat
Step 4.
Each vehicle can have a maximum of
eight transmitters matched to it.
6. To exit the programming mode, cycle the key to
LOCK/OFF.
HOLD STEM TO SET ECO (Economy)
Press and release the reset stem until HOLD STEM TO
SET ECO (Economy) displays. The HOLD STEM TO
SET ECO display will only be available when the vehicle
is in PARK (P). This display turns the fuel economy light
on or off. Once in this display, press the reset stem to
select ON (default) or OFF. SeeFuel Economy Light on
page 3-43for more information.
HOLD STEM TO CALIBRATE COMPASS
Press and release the reset stem until HOLD STEM TO
CALIBRATE COMPASS displays. The compass can
be manually calibrated. To calibrate the compass
through the DIC, seeDIC Compass on page 3-48.
HOLD STEM TO SET COMPASS ZONE
Press and release the reset stem until HOLD STEM
TO SET COMPASS ZONE displays. To change
the compass zone through the DIC, seeDIC Compass
on page 3-48.
3-47
ProCarManuals.com

DIC Compass
Your vehicle has a compass in the Driver Information
Center (DIC).
Compass Zone
The zone is set to zone eight upon leaving the factory.
Your dealer/retailer will set the correct zone for your
location.
Under certain circumstances, such as during a long
distance cross-country trip or moving to a new state or
province, it will be necessary to compensate for compass
variance by resetting the zone through the DIC if the zone
is not set correctly.
Compass variance is the difference between the earth’s
magnetic north and true geographic north. If the compass
is not set to the zone where you live, the compass may
give false readings. The compass must be set to the
variance zone in which the vehicle is traveling.
To adjust for compass variance, use the following
procedure:
Compass Variance (Zone) Procedure
1. Do not set the compass zone when the vehicle is
moving. Only set it when the vehicle is in PARK (P).
Press the reset stem until HOLD STEM TO SET
COMPASS ZONE: ## displays.2. Find the vehicle’s current location and variance
zone number on the map.
Zones 1 through 15 are available.
3. Press and hold the reset stem to scroll through and
select the appropriate variance zone.
To set the zone, release the reset stem when the
correct zone is displayed.
4. Press the reset stem until the vehicle heading,
for example, N for North, is displayed in the DIC.
5. If calibration is necessary, calibrate the compass.
See “Compass Calibration Procedure” following.
3-48
ProCarManuals.com

Compass Calibration
The compass can be manually calibrated. Only calibrate
the compass in a magnetically clean and safe location,
such as an open parking lot, where driving the vehicle
in circles is not a danger. It is suggested to calibrate
away from tall buildings, utility wires, manhole covers,
or other industrial structures, if possible.
If CAL should ever appear in the DIC display, the
compass should be calibrated.
If the DIC display does not show a heading, for
example, N for North, or the heading does not change
after making turns, there may be a strong magnetic eld
interfering with the compass. Such interference may be
caused by a magnetic CB or cell phone antenna mount, a
magnetic emergency light, magnetic note pad holder, or
any other magnetic item. Turn off the vehicle, move the
magnetic item, then turn on the vehicle and calibrate the
compass.To calibrate the compass, use the following procedure:Compass Calibration Procedure
1. Before calibrating the compass, make sure the
compass is set to the variance zone in which
the vehicle is located. See “Compass Variance
(Zone) Procedure” earlier in this section.
Do not operate any switches such as window,
sunroof, climate controls, seats, etc. during
the calibration procedure.
2. Press the reset stem until HOLD STEM TO
CALIBRATE COMPASS displays.
3. Press and hold the reset stem to start the compass
calibration.
4. The DIC will display CALIBRATING COMPASS:
TURN IN CIRCLES. Drive the vehicle in tight
circles at less than 5 mph (8 km/h) to complete
the calibration. The DIC will display COMPASS
CALIBRATION COMPLETE for a few seconds
when the calibration is complete. The DIC display
will then return to HOLD STEM TO CALIBRATE
COMPASS.
3-49
ProCarManuals.com