tire pressure SATURN VUE HYBRID 2008 Owners Manual

Instrument Panel Overview...............................3-4
Hazard Warning Flashers................................3-6
Horn .............................................................3-6
Tilt Wheel.....................................................3-6
Turn Signal/Multifunction Lever.........................3-7
Turn and Lane-Change Signals........................3-7
Headlamp High/Low-Beam Changer..................3-8
Flash-to-Pass.................................................3-8
Windshield Wipers..........................................3-8
Rainsense™ II Wipers.....................................3-9
Windshield Washer.......................................3-10
Rear Window Wiper/Washer...........................3-11
Cruise Control..............................................3-11
Exterior Lamps.............................................3-14
Wiper Activated Headlamps............................3-14
Daytime Running Lamps (DRL).......................3-15
Automatic Headlamp System..........................3-15
Instrument Panel Brightness...........................3-16
Dome Lamp .................................................3-16
Entry Lighting...............................................3-16
Reading Lamps............................................3-17
Battery Run-Down Protection..........................3-17
Accessory Power Outlet(s).............................3-17
Climate Controls............................................3-18
Automatic Climate Control System...................3-18
Outlet Adjustment.........................................3-23
Passenger Compartment Air Filter...................3-23Warning Lights, Gages, and Indicators............3-25
Instrument Panel Cluster................................3-26
Speedometer and Odometer...........................3-27
Trip Odometer..............................................3-27
Tachometer.................................................3-27
Safety Belt Reminders...................................3-28
Airbag Readiness Light..................................3-29
Passenger Airbag Status Indicator...................3-30
Charging System Light..................................3-32
Brake System Warning Light..........................3-32
Anti-lock Brake System (ABS) Warning Light. . . .3-33
Traction Control System (TCS) Warning Light . . .3-34
Electronic Stability Program Indicator Light.......3-34
Engine Coolant Temperature Warning Light......3-35
Tire Pressure Light.......................................3-35
Malfunction Indicator Lamp.............................3-36
Oil Pressure Light.........................................3-38
Change Engine Oil Light................................3-39
Security Light...............................................3-40
Cruise Control Light......................................3-40
Highbeam On Light.......................................3-40
Low Washer Fluid Warning Light.....................3-40
Fuel Gage...................................................3-41
Low Fuel Warning Light.................................3-42
Auto Stop Mode...........................................3-42
Charge/Assist Gage......................................3-43
Fuel Economy Light......................................3-43
Section 3 Instrument Panel
3-1
ProCarManuals.com

Engine Coolant Temperature
Warning Light
This light comes on briey when starting the vehicle
as a system check. If it does not, take the vehicle to
your dealer/retailer for service.
If this light comes on and
stays lit, the engine has
overheated.
If this happens pull over and seeEngine Overheating
on page 5-23for more information.
Notice:Driving with the engine coolant temperature
warning light on could cause your vehicle to
overheat. SeeEngine Overheating on page 5-23.
Your vehicle could be damaged, and it might not
be covered by your warranty. Never drive with
the engine coolant temperature warning light on.
Tire Pressure Light
The tire pressure light
comes on briey when the
engine is started.
It provides information about tire pressures and the Tire
Pressure Monitoring System.
When the Light is Solid
This indicates that one or more of your tires are
signicantly underinated.
Stop and check the tires as soon as it is safe to do,
and inate them to the proper pressure. SeeTires
on page 5-47for more information.
When the Light Flashes First and
Then is Solid
This indicates that there may be a problem with the Tire
Pressure Monitor System. The light ashes for about
a minute and then stays solid for the remainder of
the ignition cycle. This sequence will repeat with every
ignition cycle. SeeTire Pressure Monitor System on
page 5-54for more information.
3-35
ProCarManuals.com

OIL LIFE
Press and release the reset stem until OIL LIFE
REMAINING displays. The OIL LIFE display will only
be available when the vehicle is in PARK (P). This display
shows an estimate of the oil’s remaining useful life. If OIL
LIFE REMAINING 99% appears on the display, that
means 99% of the current oil life remains. The engine oil
life system will alert you to change the oil on a schedule
consistent with your driving conditions.
When the remaining oil life is low, the CHANGE
ENGINE OIL SOON message will appear on the
display. See “CHANGE ENGINE OIL SOON” under
DIC Warnings and Messages on page 3-50. Change
the oil as soon as possible. SeeEngine Oil on page 5-13.
In addition to the engine oil life system monitoring the
oil life, additional maintenance is recommended in the
Maintenance Schedule in this manual. SeeScheduled
Maintenance on page 6-4for more information.
Remember, reset the OIL LIFE after each oil change.
It will not reset itself. Also, be careful not to reset the OIL
LIFE accidentally at any time other than when the oil
has just been changed. It cannot be reset accurately
until the next oil change. To reset the engine oil
life system, seeEngine Oil Life System on page 5-16.
UNITS
Press and release the reset stem until UNITS displays.
This display selects the units of measurement. Once
in this display, press the reset stem to select ENGLISH
(default) or METRIC.
HOLD STEM TO SET LANGUAGE
Press and release the reset stem until HOLD STEM TO
SET LANGUAGE displays. The HOLD STEM TO SET
LANGUAGE display will only be available when the
vehicle is in PARK (P). This display selects the language
in which the DIC messages will appear. Once in this
display, press the reset stem to select ENGLISH
(default), SPANISH, or FRENCH.
Tire Pressure
The pressure for each tire can be viewed in the DIC.
The tire pressure will be shown in either pounds per
square inch (psi) or kilopascals (kPa). Press and release
the reset stem until the DIC displays FRONT TIRES
LEFT ## PSI (kPa) RIGHT ## PSI (kPa). Press and
release the reset stem again until the DIC displays REAR
TIRES LEFT ## PSI (kPa) RIGHT ## PSI (kPa).
If a low or high tire pressure condition is detected by the
system while driving, a message advising you to check
the pressure in a specic tire will appear in the display.
SeeInflation - Tire Pressure on page 5-52andDIC
Warnings and Messages on page 3-50for more
information.
3-46
ProCarManuals.com

If the tire pressure display shows dashes instead of a
value, there may be a problem with your vehicle. If this
consistently occurs, see your dealer/retailer for service.
HOLD STEM TO RELEARN REMOTE KEY
This display matches Remote Keyless Entry (RKE)
transmitters to your vehicle. To match a transmitter:
1. Put the vehicle in PARK (P).
2. Press and release the reset stem until HOLD STEM
TO RELEARN REMOTE KEY displays.
3. Press and hold the reset stem until REMOTE KEY
LEARNING ACTIVE is displayed.
4. Press and hold the lock and unlock buttons on
the rst transmitter at the same time for about
15 seconds.
A chime will sound indicating that the transmitter
is matched and REMOTE KEY LEARNING
COMPLETE will be displayed.
5. To match additional transmitters at this time, repeat
Step 4.
Each vehicle can have a maximum of
eight transmitters matched to it.
6. To exit the programming mode, cycle the key to
LOCK/OFF.
HOLD STEM TO SET ECO (Economy)
Press and release the reset stem until HOLD STEM TO
SET ECO (Economy) displays. The HOLD STEM TO
SET ECO display will only be available when the vehicle
is in PARK (P). This display turns the fuel economy light
on or off. Once in this display, press the reset stem to
select ON (default) or OFF. SeeFuel Economy Light on
page 3-43for more information.
HOLD STEM TO CALIBRATE COMPASS
Press and release the reset stem until HOLD STEM TO
CALIBRATE COMPASS displays. The compass can
be manually calibrated. To calibrate the compass
through the DIC, seeDIC Compass on page 3-48.
HOLD STEM TO SET COMPASS ZONE
Press and release the reset stem until HOLD STEM
TO SET COMPASS ZONE displays. To change
the compass zone through the DIC, seeDIC Compass
on page 3-48.
3-47
ProCarManuals.com

CHECK TIRE PRESSURE
This message displays when the pressure in one or
more of the vehicle’s tires needs to be checked. This
message also displays LEFT FRONT, RIGHT FRONT,
LEFT REAR, or RIGHT REAR to indicate which tire
needs to be checked. You can receive more than one tire
pressure message at a time. To read the other messages
that may have been sent at the same time, press the
reset stem. If a tire pressure message appears on the
DIC, stop as soon as you can. Have the tire pressures
checked and set to those shown on the Tire Loading
Information label. SeeTires on page 5-47,Loading Your
Vehicle on page 4-22, andInflation - Tire Pressure on
page 5-52. The DIC also shows the tire pressure values.
SeeDIC Operation and Displays on page 3-44. If the tire
pressure is low, the low tire pressure warning light comes
on. SeeTire Pressure Light on page 3-35.
COMPASS CALIBRATION COMPLETE
This message displays when the compass calibration is
complete. SeeDIC Compass on page 3-48.
CRUISE CONTROL SET TO XXX
This message displays whenever the cruise control
is set. SeeCruise Control on page 3-11for more
information.
DRIVER DOOR OPEN
This message displays when the driver door is not
closed properly. Close the door completely.
ENGINE HOT
A/C (Air Conditioning) OFF
This message displays when the engine coolant
becomes hotter than the normal operating temperature.
To avoid added strain on a hot engine, the air
conditioning compressor is automatically turned off.
When the coolant temperature returns to normal,
the A/C operation automatically resumes. You can
continue to drive your vehicle.
ENGINE OIL LOW: ADD OIL
Your vehicle may have an engine oil level sensor.
If it does, this message displays when the oill is low.
SeeEngine Oil on page 5-13for more information.
3-52
ProCarManuals.com

SERVICE TIRE MONITORING SYSTEM
This message displays if a part on the Tire Pressure
Monitor System (TPMS) is not working properly. The tire
pressure light also ashes and then remains on during
the same ignition cycle. SeeTire Pressure Light on
page 3-35. Several conditions may cause this message
to appear. SeeTire Pressure Monitor Operation on
page 5-55for more information. If the warning comes on
and stays on, there may be a problem with the TPMS.
See your dealer/retailer.
SERVICE TRACTION CONTROL
This message displays when the Traction Control
System (TCS) is not functioning properly. A warning
light also appears on the instrument panel cluster.
SeeTraction Control System (TCS) Warning Light
on page 3-34andTraction Control System (TCS) on
page 4-7for more information. Have the TCS serviced
by your dealer/retailer as soon as possible.
SERVICE TRANSMISSION
This message displays when there is a problem with the
transmission. See your dealer/retailer for service.
SERVICE VEHICLE SOON
This message displays when a non-emissions related
malfunction occurs. Have the vehicle serviced by
your dealer/retailer as soon as possible.
SPEED LIMITED TO XXX MPH (KM/H)
This message displays when your vehicle speed is
limited to 80 mph (128 km/h) because the vehicle detects
a problem in the speed variable assist steering system.
Have your vehicle serviced by your dealer/retailer.
STABILITRAK NOT READY
This message may display and a warning light on the
instrument panel cluster may be on after rst driving the
vehicle and exceeding 30 mph (48 km/h) for 30 seconds.
SeeTraction Control System (TCS) Warning Light on
page 3-34. The Electronic Stability Program (ESP) is not
functional until the light has turned off. SeeElectronic
Stability Program on page 4-8for more information.
3-56
ProCarManuals.com

STABILITRAK OFF
This message displays any time the Electronic Stability
Program (ESP) turns off. When this message has been
displayed, the system is no longer available to assist
you with directional control of the vehicle. Adjust your
driving accordingly. SeeElectronic Stability Program
on page 4-8.
This message displays only while the ignition is in
ON/RUN.
Any of the following conditions may cause the system to
turn off:
The system is turned off by pressing and holding
the ESP/TCS button. SeeElectronic Stability
Program on page 4-8for more information.
The battery is low.
There is a system failure. See your dealer/retailer
for service.
TIGHTEN GAS CAP
This message may display along with the check engine
light on the instrument panel cluster if the vehicle’s fuel
cap is not tightened properly. SeeMalfunction Indicator
Lamp on page 3-36. Reinstall the fuel cap fully. See
Filling the Tank on page 5-8. The diagnostic system can
determine if the fuel cap has been left off or improperly
installed. A loose or missing fuel cap allows fuel to
evaporate into the atmosphere. A few driving trips with
the cap properly installed should turn this light and
message off.
TIRE LEARNING ACTIVE
This message displays when the Tire Pressure Monitor
System (TPMS) is re-learning the tire positions on
your vehicle. The tire positions must be re-learned after
rotating the tires or after replacing a tire or sensor.
SeeTire Inspection and Rotation on page 5-58,
Tire Pressure Monitor System on page 5-54, and
Inflation - Tire Pressure on page 5-52for more
information.
3-57
ProCarManuals.com

Antilock Brake System (ABS)
Your vehicle has the Antilock Brake System (ABS),
an advanced electronic braking system that will
help prevent a braking skid.
When you start the engine and begin to drive away,
ABS will check itself. You might hear a momentary
motor or clicking noise while this test is going on,
and you might even notice that the brake pedal
moves a little. This is normal.
If there is a problem
with ABS, this warning
light will stay on.
SeeAnti-lock Brake
System (ABS) Warning
Light on page 3-33.
Let us say the road is wet and you are driving
safely. Suddenly, an animal jumps out in front of you.
You slam on the brakes and continue braking.
Here is what happens with ABS:
A computer senses that wheels are slowing down.
If one of the wheels is about to stop rolling, the computer
will separately work the brakes at each wheel.ABS can change the brake pressure faster than any
driver could. The computer is programmed to make the
most of available tire and road conditions. This can
help you steer around the obstacle while braking hard.
As you brake, the computer keeps receiving updates
on wheel speed and controls braking pressure
accordingly.
Remember: ABS does not change the time you need to
get your foot up to the brake pedal or always decrease
stopping distance. If you get too close to the vehicle
in front of you, you will not have time to apply the brakes
if that vehicle suddenly slows or stops. Always leave
enough room up ahead to stop, even though you
have ABS.
Using ABS
Do not pump the brakes. Just hold the brake pedal
down rmly and let antilock work for you. You might
hear the antilock pump or motor operate, and feel the
brake pedal pulsate, but this is normal.
Braking in Emergencies
With ABS, you can steer and brake at the same time.
In many emergencies, steering can help you more than
even the very best braking.
4-6
ProCarManuals.com

Before Leaving on a Long Trip
To prepare your vehicle for a long trip, consider having
it serviced by your dealer/retailer before departing.
Things to check on your own include:
Windshield Washer Fluid:Reservoir full?
Windows clean — inside and outside?
Wiper Blades:In good shape?
Fuel, Engine Oil, Other Fluids:All levels checked?
Lamps:Do they all work and are lenses clean?
Tires:Are treads good? Are tires inated
to recommended pressure?
Weather and Maps:Safe to travel?
Have up-to-date maps?
Highway Hypnosis
Always be alert and pay attention to your surroundings
while driving. If you become tired or sleepy, nd
a safe place to park your vehicle and rest.
Other driving tips include:
Keep the vehicle well ventilated.
Keep interior temperature cool.
Keep your eyes moving — scan the road ahead
and to the sides.
Check the rearview mirror and vehicle
instruments often.
Hill and Mountain Roads
Driving on steep hills or through mountains is different
than driving on at or rolling terrain. Tips for driving
in these conditions include:
Keep your vehicle serviced and in good shape.
Check all uid levels and brakes, tires, cooling
system, and transmission.
Going down steep or long hills, shift to a lower gear.
{CAUTION:
If you do not shift down, the brakes could get
so hot that they would not work well. You
would then have poor braking or even none
going down a hill. You could crash. Shift down
to let the engine assist the brakes on a steep
downhill slope.
4-16
ProCarManuals.com

Tire and Loading Information Label
A vehicle specic Tire and Loading Information
label is attached to the center pillar (B-pillar).
With the driver’s door open, you will nd the
label attached below the door lock post (striker).The tire and loading information label shows the
number of occupant seating positions (A), and the
maximum vehicle capacity weight (B) in kilograms
and pounds.
The Tire and Loading Information label also shows
the size of the original equipment tires (C) and
the recommended cold tire ination pressures (D).
For more information on tires and ination see
Tires on page 5-47andInflation - Tire Pressure
on page 5-52.
There is also important loading information on
the vehicle Certication/Tire label. It tells you
the Gross Vehicle Weight Rating (GVWR) and
the Gross Axle Weight Rating (GAWR) for the
front and rear axle. See “Certication/Tire Label”
later in this section.
Example Label
4-23
ProCarManuals.com