lock SATURN VUE HYBRID 2009 Manual PDF

3. Shift the transmission to
N (Neutral).
4. Turn fog lamps and all
accessories off.
5. To prevent the battery from
draining while the vehicle is being
towed, remove the 2 amp IGN
SW fuse from the instrument
panel fuse block and store it in a
safe location. SeeInstrument
Panel Fuse Block on page 5-76
Notice:If the vehicle is towed
without performing each of
the steps listed under “Dinghy
Towing,” the automatic
transmission could be damaged.
Be sure to follow all steps of
the dinghy towing procedure prior
to and after towing the vehicle.Notice:If the vehicle has a
four-speed automatic
transmission, it can be dinghy
towed from the front for unlimited
miles at 65 mph (105 km/h). The
vehicle could be damaged If
65 mph (105 km/h) is exceeded
while towing the vehicle. The
repairs would not be covered by
the vehicle warranty. Never
exceed 65 mph (105 km/h) while
towing the vehicle.
Once the destination has been
reached:
1. Set the parking brake.
2. Shift the transmission to
P (Park).
3. Reinstall the 2 amp IGN SW fuse
to the instrument panel fuse
block.
4. Turn the ignition key to
LOCK/OFF and remove the key
from the ignition.Notice:Too much or too
little uid can damage the
transmission. Be sure that the
transmission uid is at the proper
level before towing with all four
wheels on the ground.
Notice:Do not tow a vehicle
with the front drive wheels on the
ground if one of the front tires
is a compact spare tire. Towing
with two different tire sizes on the
front of the vehicle can cause
severe damage to the
transmission.
4-24 Driving Your Vehicle
ProCarManuals.com

Tires
Tires.................................5-38
Tire Sidewall Labeling.......5-39
Tire Terminology and
Denitions.......................5-41
Ination - Tire Pressure. . . .5-43
Tire Pressure Monitor
System............................5-45
Tire Pressure Monitor
Operation........................5-46
Tire Inspection and
Rotation..........................5-50
When It Is Time for
New Tires.......................5-51
Buying New Tires.............5-51
Different Size Tires and
Wheels............................5-53
Uniform Tire Quality
Grading...........................5-54
Wheel Alignment and
Tire Balance....................5-55
Wheel Replacement..........5-55
Tire Chains.......................5-57
If a Tire Goes Flat............5-58
Tire Sealant and
Compressor Kit...............5-59
Tire Sealant and
Compressor Kit
Storage
...........................5-66
Appearance Care
Interior Cleaning................5-66
Fabric/Carpet....................5-68
Leather.............................5-68
Instrument Panel, Vinyl,
and Other Plastic
Surfaces
..........................5-69
Care of Safety Belts.........5-69
Weatherstrips....................5-69
Washing Your Vehicle.......5-69
Cleaning Exterior
Lamps/Lenses.................5-70
Finish Care.......................5-70
Windshield and Wiper
Blades.............................5-71
Aluminum Wheels.............5-72
Tires.................................5-72
Sheet Metal Damage........5-73
Finish Damage..................5-73
Underbody Maintenance. . . .5-73
Chemical Paint Spotting. . . .5-73
Vehicle Identication
Vehicle Identication
Number (VIN)..................5-74
Service Parts
Identication Label...........5-74
Electrical System
Intermediate Voltage
Devices and Wiring.........5-74
Add-On Electrical
Equipment.......................5-75
Windshield Wiper Fuses. . . .5-75
Power Windows and
Other Power Options.......5-75
Fuses and Circuit
Breakers.........................5-75
Instrument Panel Fuse
Block...............................5-76
Underhood Fuse Block......5-77
Capacities and
Specications
Capacities and
Specications..................5-81
5-2 Service and Appearance Care
ProCarManuals.com

Service
For service and parts needs, visit
your dealer/retailer. You will receive
genuine Saturn parts and
Saturn-trained and supported
service people.
Genuine Saturn parts have one of
these marks.
Accessories and
Modications
When non-dealer/non-retailer
accessories are added to the vehicle,
they can affect vehicle performance
and safety, including such things as
airbags, braking, stability, ride and
handling, emissions systems,
aerodynamics, durability, and
electronic systems like antilock
brakes, traction control, and stability
control. Some of these accessories
could even cause malfunction or
damage not covered by the vehicle
warranty.
Damage to vehicle components
resulting from the installation or use
of non-GM certied parts, including
control module modications, are not
covered under the terms of the
vehicle warranty and may affect
remaining warranty coverage for
affected parts.
GM Accessories are designed to
complement and function with
other systems on the vehicle.Your GM dealer/retailer can
accessorize the vehicle using
genuine GM Accessories. When you
go to your GM dealer/retailer and
ask for GM Accessories, you
will know that GM-trained and
supported service technicians will
perform the work using genuine GM
Accessories.
Also, seeAdding Equipment to Your
Airbag-Equipped Vehicle on
page 1-55.
California Proposition 65
Warning
Most motor vehicles, including this
one, contain and/or emit chemicals
known to the State of California
to cause cancer and birth defects or
other reproductive harm. Engine
exhaust, many parts and systems
(including some inside the vehicle),
many uids, and some component
wear by-products contain and/or
emit these chemicals.
Service and Appearance Care 5-3
ProCarManuals.com

Filling the Tank
{CAUTION
Fuel vapor burns violently and a
fuel re can cause bad injuries.
To help avoid injuries to you and
others, read and follow all the
instructions on the pump island.
Turn off the engine when you are
refueling. Do not smoke if you are
near fuel or refueling the vehicle.
Do not use cellular phones. Keep
sparks, ames, and smoking
materials away from fuel. Do not
leave the fuel pump unattended
when refueling the vehicle. This is
against the law in some places.
Do not re-enter the vehicle while
pumping fuel. Keep children away
from the fuel pump; never let
children pump fuel.Unlock the gas cap door by pressing
the door lock switch located on
the driver door trim.
The tethered fuel cap is located
behind a hinged fuel door on
the driver side of the vehicle.
To remove the fuel cap, turn it
slowly counterclockwise. The fuel
cap has a spring in it; if the cap
is released too soon, it will spring
back to the right. To avoid fuel
contact on the painted surface of
the vehicle when lling the fuel tank,
place the tethered cap on the fuel
ller door.
{CAUTION
Fuel can spray out on you if you
open the fuel cap too quickly. If
you spill fuel and then something
ignites it, you could be badly
burned. This spray can happen if
the tank is nearly full, and is more
likely in hot weather. Open the
fuel cap slowly and wait for any
hiss noise to stop. Then unscrew
the cap all the way.
Be careful not to spill fuel. Do not
top off or overll the tank and wait a
few seconds after you have
nished pumping before removing
the nozzle. Clean fuel from
painted surfaces as soon as
possible. SeeWashing Your Vehicle
on page 5-69.
When replacing the fuel cap, turn
it clockwise until it clicks. Make
sure the cap is fully installed.
The diagnostic system can
determine if the fuel cap has been
left off or improperly installed.
Service and Appearance Care 5-7
ProCarManuals.com

A. SeeEngine Air Cleaner/Filter on
page 5-15.
B. Remote Negative (−) Terminal.
SeeJump Starting on page 5-28.
C. Engine Oil Fill Cap. SeeEngine
Oil on page 5-11.
D. Engine Coolant Surge Tank. See
Cooling System on page 5-17.
E. Engine Coolant Surge Tank
Protection Cap. SeeCoolant
Surge Tank Pressure Cap
on page 5-22.
F. SeeUnderhood Fuse Block on
page 5-77.
G. Remote Positive (+) Terminal.
SeeJump Starting on page 5-28.H. Windshield Washer Fluid
Reservoir. SeeWindshield
Washer Fluid on page 5-24.
I. Engine Oil Dipstick (out of view).
SeeEngine Oil on page 5-11.
Engine Oil
Checking Engine Oil
It is a good idea to check the
engine oil level at each fuel ll. In
order to get an accurate reading, the
oil must be warm and the vehicle
must be on level ground.The engine oil dipstick handle is a
yellow loop. SeeEngine
Compartment Overview on
page 5-10for the location of the
engine oil dipstick.
1. Turn off the engine and give the
oil several minutes to drain back
into the oil pan. If this is not
done, the oil dipstick might not
show the actual level.
2. Pull the dipstick and clean it with
a paper towel or cloth, then push
it back in all the way. Remove
it again, keeping the tip down and
check the level.
Service and Appearance Care 5-11
ProCarManuals.com

{CAUTION
Adding only plain water to the
cooling system can be dangerous.
Plain water, or some other liquid
such as alcohol, can boil before
the proper coolant mixture will.
The vehicle’s coolant warning
system is set for the proper
coolant mixture. With plain water
or the wrong mixture, the engine
could get too hot but you would
not get the overheat warning. The
engine could catch re and you or
others could be burned. Use a
50/50 mixture of clean, drinkable
water and DEX-COOL
®coolant.Notice:In cold weather, water
can freeze and crack the engine,
radiator, heater core and other
parts. Use the recommended
coolant and the proper coolant
mixture.
{CAUTION
You can be burned if you spill
coolant on hot engine parts.
Coolant contains ethylene glycol
and it will burn if the engine parts
are hot enough. Do not spill
coolant on a hot engine.1. You can remove the coolant
surge tank pressure cap
when the cooling system,
including the coolant surge tank
pressure cap and upper
radiator hose, is no longer hot.
Turn the pressure cap slowly
counterclockwise about
one-quarter of a turn. If you hear
a hiss, wait for that to stop.
This will allow any pressure still
left to be vented out the
discharge hose.
2. Then keep turning the pressure
cap slowly, and remove it.
Service and Appearance Care 5-19
ProCarManuals.com

5. The remote negative (−) terminal
is a stud on the driver side near
the underhood fuse block.
{CAUTION
Using a match near a battery can
cause battery gas to explode.
People have been hurt doing this,
and some have been blinded. Use
a ashlight if you need more light.
Be sure the battery has enough
water. You do not need to add
water to the battery installed in
your new vehicle. But if a battery
has ller caps, be sure the right
amount of uid is there. If it is
low, add water to take care of that
rst. If you do not, explosive gas
could be present.
(Continued)
CAUTION (Continued)
Battery uid contains acid that
can burn you. Do not get it on
you. If you accidentally get it in
your eyes or on your skin, ush
the place with water and get
medical help immediately.
{CAUTION
An electric fan can start up even
when the engine is not running
and can injure you. Keep hands,
clothing and tools away from any
underhood electric fan.
{CAUTION
Fans or other moving engine
parts can injure you badly. Keep
your hands away from moving
parts once the engine is running.6. Check that the jumper cables
do not have loose or missing
insulation. If they do, you could
get a shock. The vehicles could
be damaged too. Before you
connect the cables to the other
vehicle, here are some basic
things you should know.
Positive (+) will go to positive (+)
or to a remote positive
terminal (+) if the vehicle has one.
Negative (−) will go to a heavy,
unpainted metal engine part or to
a remote negative (−) terminal, if
the vehicle has one. Do not
connect positive (+) to
negative (−) or you will get a short
that would damage the battery
and maybe other parts too.
7. Connect the red positive (+)
cable to the remote positive (+)
terminal of your hybrid vehicle.
8. Do not let the other end touch
metal. Connect it to the
positive (+) terminal of the good
battery. Use a remote
positive (+) terminal if the other
vehicle has one.
Service and Appearance Care 5-31
ProCarManuals.com

4. At the wall measure from the
ground upward (A) to the
recorded distance from Step 3
and mark it.
5. Draw or tape a horizontal line (B)
on the wall the width of the
vehicle at the height of the mark
in Step 4.
Notice:Do not cover a headlamp
to improve beam cut-off when
aiming. Covering a headlamp may
cause excessive heat build-up
which may cause damage to the
headlamp.6. Turn on the low-beam headlamps
and place a piece of cardboard
or equivalent in front of the
headlamp not being adjusted.
This allows only the beam of light
from the headlamp being
adjusted to be seen on the at
surface.
7. Locate the vertical headlamp
aiming screws, which are
under the hood near each
headlamp assembly.
The adjustment screw can be
turned with a E8 Torx
®socket.8. Turn the vertical aiming screw
until the headlamp beam is
aimed to the horizontal tape line.
Turn it clockwise or
counterclockwise to raise or
lower the angle of the beam.
9. Make sure that the light from the
headlamp is positioned at the
bottom edge of the horizontal
tape line. The lamp on the left (A)
shows the correct headlamp aim.
The lamp on the right (B) shows
the incorrect headlamp aim.
10. Repeat Steps 7 through 9 for
the opposite headlamp.
5-34 Service and Appearance Care
ProCarManuals.com

Bulb Replacement
For the proper type of replacement
bulbs, seeReplacement Bulbs
on page 5-37.
For any bulb changing procedure
not listed in this section, contact
your dealer/retailer.
Halogen Bulbs
{CAUTION
Halogen bulbs have pressurized
gas inside and can burst if you
drop or scratch the bulb. You or
others could be injured. Be sure
to read and follow the instructions
on the bulb package.
Headlamps
To replace one of the headlamp
bulbs, use the following procedure.
To replace the parking/turn signal
lamp bulb, seeFront Turn Signal
and Parking Lamps on page 5-36.
1. Open the hood. SeeHood
Release on page 5-9for
more information.
2. Remove the two screws from the
top of the front fascia and grille.
They are inboard of the
headlamp assembly.
3. Remove the three screws
retaining the headlamp assembly.
4. Insert a at blade tool through the
opening in the top. Make sure the
tool ts through the opening in the
headlamp bracket lower arm.
5. Push the locking tab toward
the rear of the vehicle with the
tool to lift the headlamp bracket
lower arm.6. Pull back on the front fascia and
then pull the headlamp assembly
out from the vehicle. Another
person might be needed to assist
with this step.
7. Disconnect the electrical
connector from the bulb
assembly.
8. Turn the bulb assembly
counterclockwise to remove it
from the housing.
9. Replace the old bulb with a
new one.
10. Reverse Steps 1 through 8 to
reinstall.
Service and Appearance Care 5-35
ProCarManuals.com

Front Turn Signal and
Parking Lamps
To replace a front turn signal or
parking lamp bulb:
1. Follow Steps 1 through 6 under
Headlamps on page 5-35to
access the front turn signal or
parking lamp.
2. Turn the bulb to be replaced
counterclockwise to remove
it from the headlamp assembly.3. Pull the bulb out of the bulb
socket assembly.
4. Push the new bulb into the bulb
socket assembly.
5. Insert the bulb assembly into the
headlamp assembly.
6. Turn the bulb assembly
clockwise until seated.
7. Reverse the steps to reinstall the
headlamp assembly.
Taillamps, Turn Signal,
Stoplamps and Back-up
Lamps
To replace one of these bulbs:
A. Taillamp/Stoplamp
B. Turn Signal Lamp
C. Back-up Lamp
5-36 Service and Appearance Care
ProCarManuals.com