display SATURN VUE HYBRID 2009 Owners Manual

Programming Transmitters to
the Vehicle
Only RKE transmitters programmed
to the vehicle will work. If a
transmitter is lost or stolen, a
replacement can be purchased and
programmed through your dealer/
retailer. When the replacement
transmitter is programmed to the
vehicle, all remaining transmitters
must also be programmed. Any lost
or stolen transmitters no longer work
once the new transmitter is
programmed. Each vehicle can have
up to eight transmitters programmed
to it. See “HOLD STEM TO
RELEARN REMOTE KEY” under
DIC Operation and Displays on
page 3-36.
Battery Replacement
Replace the battery if the REPLACE
REMOTE KEY FOB BATTERY
message displays on the Driver
Information Center (DIC). See
“REPLACE REMOTE KEY FOB
BATTERY” underDIC Warnings
and Messages on page 3-42.
Notice:When replacing the
battery, do not touch any of the
circuitry on the transmitter. Static
from your body could damage
the transmitter.To replace the battery:
1. Separate the transmitter with a
at thin object inserted into the
notch on the side.
2. Remove the old battery. Do not
use a metal object.
3. Insert the new battery, positive
side facing down. Replace with
a CR2032 or equivalent battery.
4. Reassemble the transmitter.
Features and Controls 2-5
ProCarManuals.com

ACC (ACC/ACCESSORY):This is
the position in which you can operate
the electrical accessories or items
plugged into the accessory power
outlets.
Use this position if the vehicle must
be pushed or towed.
ON/RUN:This position can be used
to operate the electrical accessories
and to display some instrument
panel cluster warning and indicator
lights. The switch stays in this
position when the engine is running.
The transmission is also unlocked in
this position. If you leave the key in
the ACC/ACCESSORY or ON/RUN
positions with the engine off, the
battery could be drained. You may
not be able to start the vehicle if the
battery is allowed to drain for an
extended period of time.START:This is the position that
starts the engine. When the engine
starts, release the key. The ignition
switch returns to ON/RUN for driving.
A warning tone will sound when the
driver door is opened, the ignition is
in ACC/ACCESSORY or LOCK/OFF
and the key is in the ignition.
Retained Accessory
Power (RAP)
These vehicle accessories may be
used for up to 10 minutes after
the ignition key is turned off:
Outside Mirror
Power Windows
Radio
All these features work when the
ignition key is in the ON/RUN
or ACC/ACCESSORY positions,
until a door is opened.
Starting the Engine
(Automatic Engine
Start/Stop)
Place the transmission in the
proper gear.
Move the shift lever to P (Park) or
N (Neutral). The engine will not start
in any other position. To restart the
engine when the vehicle is already
moving, use N (Neutral) only.
Notice:Do not try to shift to
P (Park) if the vehicle is moving.
If you do, you could damage
the transmission. Shift to P (Park)
only when the vehicle is stopped.
Starting Procedure
1. With your foot off the accelerator
pedal, turn the ignition key to
START. When the engine starts,
let go of the key. The idle speed
will go down as your engine gets
warm. Do not race the engine
immediately after starting it.
Features and Controls 2-15
ProCarManuals.com

Manual Shift Mode (MSM)
(Automatic Transmission)
To use this feature, do the following:
1. Move the shift lever from
D (Drive) rearward to the
M (Manual Mode).
The display will show a 3 for
third gear.
When coming to a stop in
the manual position, the
vehicle will automatically shift
to 1 (First) gear.
2. Press the plus (+) button to
upshift or the minus (−) button
to downshift.
While driving in MSM, the vehicle
will have sportier performance. Use
this when you want the vehicle
to stay in gear longer or to downshift
for more power or engine braking.The transmission will only allow you
to shift into a gear range appropriate
for the vehicle speed.The transmission will not
automatically shift to the next
higher gear range without
pressing the button on the
shifter handle.
The transmission will not allow
shifting to the next lower gear
if the vehicle speed is too high.
If the vehicle does not respond to a
gear change, or detects a problem
with the transmission, the range
of gears may be reduced and
the Malfunction Indicator Lamp
will come on. SeeMalfunction
Indicator Lamp on page 3-30.
Parking Brake
The parking brake lever is located in
the center console between the
front seats.
To set the parking brake, hold the
brake pedal down and pull up on the
parking brake lever. If the ignition
is in ON/RUN, the brake system
warning light will come on.
2-22 Features and Controls
ProCarManuals.com

Tire Pressure Light...........3-29
Malfunction
Indicator Lamp................3-30
Oil Pressure Light.............3-33
Change Engine Oil Light. . .3-33
Security Light....................3-33
Cruise Control Light..........3-33
Highbeam On Light...........3-34
Low Washer Fluid
Warning Light..................3-34
Fuel Gage........................3-34
Low Fuel Warning Light. . . .3-34
Auto Stop Mode................3-35
Charge/Assist Gage..........3-35
Fuel Economy Light..........3-35
Driver Information
Center (DIC)
Driver Information
Center (DIC)...................3-36
DIC Operation and
Displays..........................3-36
DIC Compass...................3-40
DIC Warnings and
Messages........................3-42
DIC Vehicle
Customization..................3-49
Audio System(s)
Audio System(s)................3-56
Setting the Clock..............3-56
Radio(s)............................3-58
Using an MP3...................3-66
XM Radio Messages.........3-71
Bluetooth®........................3-72
Theft-Deterrent Feature.....3-82
Audio Steering Wheel
Controls..........................3-82
Radio Reception...............3-83
Fixed Mast Antenna..........3-84
XM™ Satellite Radio
Antenna System..............3-84
Chime Level Adjustment. . .3-84
3-2 Instrument Panel
ProCarManuals.com

Instrument Panel
Brightness
This feature controls the brightness
of the instrument panel lights.
The thumbwheel for this feature is
located on the left side of the
steering wheel next to the exterior
lamps control.
Turn the thumbwheel to the right or
left to brighten or dim the lights.
Dome Lamp
*
(Dome Lamp Override):Press
this button to keep the dome
lamps and other interior lamps
turned off while any door is open.
Press this button again to return it to
the out position and the lamps
automatically come on when any
door is opened.
+(On/Off):Press this button to
turn the dome lamps on and off
while the doors are closed.
Entry Lighting
If the dome lamp override button is
in the out position, the lamps
inside the vehicle automatically
come on when any door is opened
or when the Remote Keyless
Entry (RKE) unlock button is
pressed. After the door is opened
the lights remain on and stay on for
20 seconds after the doors are
closed, or until the key is put into
the ignition and turned to theACC/ACCESSORY position. The
lights will then gradually dim until it
is no longer lit.
Reading Lamps
The reading lamps are located on
the overhead console.
To turn the reading lamps on or off,
press the button located next to
each lamp.
Electric Power
Management
The vehicle has Electric Power
Management (EPM) that estimates
the battery’s temperature and
state of charge. It then adjusts the
voltage for best performance
and extended life of the battery.
When the battery’s state of charge is
low, the voltage is raised slightly to
quickly bring the charge back up.
When the state of charge is high, the
voltage is lowered slightly to prevent
overcharging. If the vehicle has a
voltmeter gage or a voltage display
3-14 Instrument Panel
ProCarManuals.com

on the Driver Information Center
(DIC), you may see the voltage move
up or down. This is normal. If there is
a problem, an alert will be displayed.
The battery can be discharged at
idle if the electrical loads are
very high. This is true for all
vehicles. This is because the
generator (alternator) may not be
spinning fast enough at idle to
produce all the power that is needed
for very high electrical loads.
A high electrical load occurs when
several of the following are on, such
as: headlamps, high beams, fog
lamps, rear window defogger,
climate control fan at high speed,
heated seats, engine cooling fans,
trailer loads, and loads plugged into
accessory power outlets.EPM works to prevent excessive
discharge of the battery. It does this
by balancing the generator’s output
and the vehicle’s electrical needs. It
can increase engine idle speed to
generate more power, whenever
needed. It can temporarily reduce
the power demands of some
accessories.
Normally, these actions occur in
steps or levels, without being
noticeable. In rare cases at the
highest levels of corrective action,
this action may be noticeable to the
driver. If so, a Driver Information
Center (DIC) message might be
displayed, such as BATTERY
SAVER ACTIVE, BATTERY
VOLTAGE LOW, or LOW BATTERY.
If this message is displayed, it is
recommended that the driver reduce
the electrical loads as much as
possible. SeeDIC Warnings and
Messages on page 3-42.Battery Run-Down
Protection
The battery saver feature is
designed to protect the vehicle’s
battery.
If any interior or exterior lamp is left
on and the ignition is turned off, the
battery rundown protection system
automatically turns the lamp off after
10 minutes.
Instrument Panel 3-15
ProCarManuals.com

Speedometer and
Odometer
The speedometer shows the
vehicle’s speed in both miles
per hour (mph) and kilometers
per hour (km/h).
The odometer shows how far the
vehicle has been driven, in
either miles or kilometers.
If the vehicle needs a new odometer
installed, the new one is set to
the mileage total of the old
odometer. If it cannot, it will be set
at zero and a label must be put
on the driver’s door to show the old
mileage reading when the new
odometer was installed. If the
mileage is unknown, the label
should then indicate that the
previous mileage is unknown.
Trip Odometer
The trip odometer is located on the
instrument panel and shows how
far the vehicle has been driven since
the trip odometer was last reset.
To reset the trip odometer to zero,
press and hold the trip/reset
button on the speedometer for
about two seconds. Press the
trip/reset button to switch between
the trip odometer and odometer.
Tachometer
The tachometer displays the
engine speed in revolutions
per minute (rpm).The auto stop indicator is located at
the bottom of the tachometer. For
more information seeAuto Stop
Mode on page 3-35.
Safety Belt Reminders
Driver Safety Belt Reminder
Light
When the engine is started, a chime
sounds for several seconds to
remind the driver to fasten their
safety belt, unless it is already
buckled.
The safety belt light comes on and
stays on for several seconds,
then ashes for several more.
This chime and light are repeated if
the driver safety belt remains
unbuckled and the vehicle is in
motion. If the driver safety belt is
already buckled, neither the
chime nor the light comes on. U.S. shown, Canada similar
3-24 Instrument Panel
ProCarManuals.com

This light also comes on when the
fuel tank is low on fuel. When fuel is
added, the light should go off. If it
does not, have the vehicle serviced.
Auto Stop Mode
This mark on the tachometer
signies that the engine is in Auto
Stop mode which is a fuel saving
operation.
When the vehicle is off, the
tachometer needle moves to OFF. If
the driver’s door is opened while
in Auto Stop, a chime sounds.
Charge/Assist Gage
The CHARGE/ASSIST gage
displays the charge into and out of
the hybrid battery.
When the gage indicates ASSIST,
the electric motor is performing
an automatic restart of the engine,
or the electric motor is assisting
for maximum acceleration.
When the gage indicates CHARGE,
the electric motor operates as a
generator to perform regenerative
braking, while decelerating. See
Regenerative Braking on page 2-23
for more information.
The gage also indicates CHARGE
when the system is recharging
the hybrid battery.If the hybrid battery or other hybrid
components are very hot or cold, the
CHARGE and ASSIST functions can
be suspended until the component
temperatures are normal.
Fuel Economy Light
The ECO light comes on when the
vehicle is achieving fuel economy
close to its rated performance.
Driving habits that improve
fuel economy increases the time
that the fuel economy light is on.
To enable or disable the fuel
economy light, while in park, press
the Vehicle Info button on the
DIC until PRESS
VTO SET ECO is
displayed. Then press the set/reset
button to select off or on. For
more information seeTrip Odometer
on page 3-24andDIC Operation
and Displays on page 3-36. United States
Canada
Instrument Panel 3-35
ProCarManuals.com

Driver Information
Center (DIC)
Your vehicle has a Driver
Information Center (DIC).
All information appears in the DIC
display located in the instrument
panel cluster.
The DIC comes on when the
ignition is on. After a short delay,
the DIC displays the information that
was last displayed before the
engine was turned off.
The DIC displays trip, fuel, and
vehicle system information, and
warning messages if a system
problem is detected.
The DIC also displays the compass
direction, outside air temperature,
and shift position indicator at the top
of the DIC display. If there is a
problem with the system that controls
the temperature display, the
numbers will be replaced with
dashes. If this occurs, have the
vehicle serviced by your dealer/retailer. If an abnormal temperature
reading is displayed for an
extended period of time, consult
your dealer/retailer. Under certain
circumstances, especially when the
engine is idling, a delay updating the
temperature display is normal.
SeeDIC Compass on page 3-40
andAutomatic Transmission
Operation on page 2-20for more
information.
DIC Operation and
Displays
The DIC has different displays
which can be accessed by pressing
the DIC buttons located on the
instrument panel, below the
headlamp switch.
The DIC displays trip, fuel, and
vehicle system information, and
warning messages if a system
problem is detected.The DIC also allows some features
to be customized. SeeDIC Vehicle
Customization on page 3-49for more
information.
DIC Buttons
The buttons are the trip/fuel, vehicle
information, customization, and
set/reset buttons. The button
functions are detailed in the
following pages.
3(Trip/Fuel):Press this button
to display the odometer, trip
odometer, fuel range, average
economy, and instantaneous
economy. The compass and outside
temperature will also be shown in
the display. The temperature will be
shown in °F or °C depending on
the units selected.
3-36 Instrument Panel
ProCarManuals.com

T(Vehicle Information):Press
this button to display the oil life,
units, tire pressure readings
for vehicles with the Tire Pressure
Monitor System (TPMS), Remote
Keyless Entry (RKE) transmitter
programming, economy light on/off,
compass zone setting, and
compass recalibration on vehicles
with this feature.
U(Customization):Press this
button to customize the feature
settings on your vehicle. SeeDIC
Vehicle Customization on page 3-49
for more information.
V(Set/Reset):Press this button to
set or reset certain functions and
to turn off or acknowledge
messages on the DIC.
Trip/Fuel Menu Items
3(Trip/Fuel):Press this button
to scroll through the following
menu items:
Odometer
Press the trip/fuel button until
ODOMETER displays. This display
shows the distance the vehicle
has been driven in either miles (mi)
or kilometers (km). Pressing the
trip odometer reset stem will
also display the odometer.
To switch between English and
metric measurements, see “Units”
later in this section.
Trip Odometer
Press the trip/fuel button until TRIP
displays. This display shows the
current distance traveled in
either miles (mi) or kilometers (km)
since the last reset for the trip
odometer. Pressing the trip
odometer reset stem will also
display the trip odometer.The trip odometer can be reset to
zero by pressing the set/reset button
while the trip odometer is displayed.
You can also reset the trip
odometer while it is displayed by
pressing and holding the trip
odometer reset stem.
Fuel Range
Press the trip/fuel button until
FUEL RANGE displays. This
display shows the approximate
number of remaining miles (mi) or
kilometers (km) the vehicle can be
driven without refueling. The display
will show LOW if the fuel level is low.
The fuel range estimate is based on
an average of the vehicle’s fuel
economy over recent driving history
and the amount of fuel remaining
in the fuel tank. This estimate
will change if driving conditions
change. For example, if driving in
traffic and making frequent
stops, this display may read one
number, but if the vehicle is driven
on a freeway, the number may
change even though the same
Instrument Panel 3-37
ProCarManuals.com