technical data Seat Alhambra 2005 Owner's Manual

203 If and when
Safety FirstControls and equipment Tips and Maintenance Technical Data
Vehicles may also have:
– Tool box*
– Wheel bolt spanner
– Wire hook* for wheel trims
– Open jaw spanner 10 x 13
– Screwdriver with box spanner in handle for the wheel bolts. The
screwdriver blade is reversible.
– Jack
Before the jack is placed back into the tool box, the claw must be
fully wound back. The crank is then tensioned against the side of
the jack.
Some light alloy wheels have the caps on the wheel screws. A
special wire hook is provided with the tool box to remove them.
Place the hook in the orifice on the cap and pull to remove
⇒
fig. 168.K
Stowage of tow bracket*
Fig. 169
Fig. 170
AL0-131
AL0-132

205 If and when
Safety FirstControls and equipment Tips and Maintenance Technical Data
• Remove the rubber seal⇒ fig. 171Bon the eyelet upwards.
• Take the wheel spanner
⇒ fig. 171Cfrom the vehicle tools.
Place it as far as it will go over the bolt. Hold in this position and
press the locking ring
⇒ fig. 171Ddown.
• Turn the box spanner
Cto the left until it is supporting the
spare wheel, which issuspended from a steel cable
⇒ fig. 171.
• Squeeze the retainer lightly (arrows
1) and at the same time
fold the cross piece in the direction shown 2⇒ fig. 172. Now
guide the retainer through the central opening in the spare
wheel.
K
Installing spare wheel
• Stand the wheel behind the vehicle, as shown in the fig. 173.• Guide the retainer from the inner side of the wheel through the
spare wheel central opening.
• Fold the cross piece in the opposite to arrow
⇒ fig. 1722.
• Push the spare wheel under the vehicle with the outer side facing
down.
• Turn the bolt in the luggage compartment floor clockwise with
the wheel spanner to lift the wheel into the spare wheel bracket
under the vehicle. E En
ns
su
ur
re
e tth
ha
at
t tth
he
e ssp
pa
ar
re
e wwh
he
ee
el
l ffi
it
ts
s iin
nt
to
o tth
he
e rre
ec
ce
es
ss
s
( (a
ar
rr
ro
ow
ws
s)
) iin
n tth
he
e bbu
um
mp
pe
er
r
⇒ fig. 173.
• Turn the bolt (max. torque 25 Nm) until the spare wheel sits
firmly in the luggage compartment floor. Seal the opening with the
rubber seal and fold the cover back.
N No
ot
te
e
If you need to drive without a spare wheel, the spare wheel bracket,
together with the rope, must be fully wound up to the vehicle floor.K
W
Wh
he
ee
el
ls
s
General notes
• New tyres do not give maximum grip straight away and should
therefore be run in at moderate speeds and a careful style of
driving for about the first 100 km. This will help to make the tyres
last longer.

Fig. 173AL0-135

207 If and when
Safety FirstControls and equipment Tips and Maintenance Technical Data
The inflation pressure is very important particularly at high speeds.
Therefore, the pressures should be checked at least once a
month and before every long journey.
At this opportunity do not forget the spare wheel:
• The spare wheel with normal tyre should always be inflated to
the highest pressure required on the vehicle.
• Always check the pressures when the tyres are cold. When warm,
the pressure is higher but do not reduce. If the load changes a
great deal the pressure must be altered to suit.
On vehicles with wheel hub caps, valve extensions are fitted. It is
not necessary to remove the valve extension piece in order to test
and correct the inflation pressure.
P Pr
re
es
ss
su
ur
re
es
s wwh
hi
ic
ch
h aar
re
e tto
oo
o hhi
ig
gh
h oor
r tto
oo
o llo
ow
w ssh
ho
or
rt
te
en
n tty
yr
re
e lli
if
fe
e –– qqu
ui
it
te
e
a ap
pa
ar
rt
t ffr
ro
om
m tth
he
e dde
et
tr
ri
im
me
en
nt
ta
al
l iin
nf
fl
lu
ue
en
nc
ce
e oon
n vve
eh
hi
ic
cl
le
e hha
an
nd
dl
li
in
ng
g.
.
F Fo
or
r tth
he
e ssa
ak
ke
e oof
f tth
he
e een
nv
vi
ir
ro
on
nm
me
en
nt
t
A pressure which is too low increases the fuel consumption and this
burdens the environment unnecessarily.
M Mo
od
de
e oof
f ddr
ri
iv
vi
in
ng
g
Fast cornering, hard acceleration and violent braking also increase
tyre wear.
B Ba
al
la
an
nc
ci
in
ng
g wwh
he
ee
el
ls
s
The wheels on new vehicles are balanced. However when the
vehicle is running various influences can cause the wheels to
become unbalanced and this causes steering vibration.
As imbalance also increases steering, suspension and tyre wear
the wheels should be balanced again. Furthermore a wheel should
always be rebalanced when the tyre has been repaired or when a
new tyre has been fitted.
I In
nc
co
or
rr
re
ec
ct
t wwh
he
ee
el
l aal
li
ig
gn
nm
me
en
nt
t
Incorrect wheel alignment not only causes excessive, usually
uneven, tyre wear but can also impair the vehicle’s safe handling.
In case of abnormal tyre wear, contact a Technical Service Centre.
W We
ea
ar
r iin
nd
di
ic
ca
at
to
or
rs
s
At the bottom of the tread of the original tyres there are 1.6 mm
high “wear indicators” running across the tread
⇒fig. 174. There
are 6-8 of these indicators – according to make – evenly spaced
around the tyre circumference. Marks on the walls of the tyre (for
example the letters “TWI” or triangles) show the locations of the
wear indicators.

A At
t cco
on
nt
ti
in
nu
uo
ou
us
s hhi
ig
gh
h ssp
pe
ee
ed
ds
s aa tty
yr
re
e iin
n wwh
hi
ic
ch
h tth
he
e ppr
re
es
ss
su
ur
re
e iis
s tto
oo
o llo
ow
w ffl
le
ex
xe
es
s
m mo
or
re
e aan
nd
d hhe
ea
at
ts
s uup
p eex
xc
ce
es
ss
si
iv
ve
el
ly
y.
. TTh
hi
is
s cca
an
n cca
au
us
se
e ttr
re
ea
ad
d sse
ep
pa
ar
ra
at
ti
io
on
n aan
nd
d tty
yr
re
e
b bl
lo
ow
w oou
ut
t.
.
W
WA
AR
RN
NI
IN
NG
G

209 If and when
Safety FirstControls and equipment Tips and Maintenance Technical Data
T
Th
he
e mma
an
nu
uf
fa
ac
ct
tu
ur
ri
in
ng
g dda
at
te
e
is also to be seen on the tyre wall
(possibly only on inner side of wheel):
DOT ... 185 means that the tyre was manufactured the 18
thweek of
2005.
I If
f yyo
ou
u wwi
is
sh
h tto
o ffi
it
t yyo
ou
ur
r cca
ar
r wwi
it
th
h nno
on
n-
-s
st
ta
an
nd
da
ar
rd
d wwh
he
ee
el
ls
s oor
r tty
yr
re
es
s ppl
le
ea
as
se
e
n no
ot
te
e:
:Technical Service Centres have all the necessary information about
the possible conversion of wheels, tyres and wheel trims.K
Wheel bolts
T Th
he
e wwh
he
ee
el
l bbo
ol
lt
ts
s mmu
us
st
t bbe
e ccl
le
ea
an
n aan
nd
d eea
as
sy
y tto
o ttu
ur
rn
n –– ddo
o nno
ot
t ggr
re
ea
as
se
e oor
r
o oi
il
l uun
nd
de
er
r aan
ny
y cci
ir
rc
cu
um
ms
st
ta
an
nc
ce
es
s!
!
T Th
hi
is
s aap
pp
pl
li
ie
es
s nno
ot
t oon
nl
ly
y tto
o cch
ha
an
ng
gi
in
ng
g aa dde
ef
fe
ec
ct
ti
iv
ve
e wwh
he
ee
el
l bbu
ut
t aal
ls
so
o wwh
he
en
n
r re
ep
pl
la
ac
ci
in
ng
g ssu
um
mm
me
er
r tty
yr
re
es
s wwi
it
th
h wwi
in
nt
te
er
r tty
yr
re
es
s aan
nd
d vvi
ic
ce
e-
-v
ve
er
rs
sa
a.
.
K
e.g. 1 19
95
5 // 665
5 RR 115
5 991
1 TT
1 19
95
5
= Tyre width in mm
6 65
5
= Height/width ratio in %
R R
= Radial construction code letter = Radial
1 15
5
= Wheel diameter in inches
9 91
1
= Carrying capability code
T T
= Speed code letter
T Ty
yr
re
es
s wwh
hi
ic
ch
h aar
re
e mmo
or
re
e tth
ha
an
n 66 yye
ea
ar
rs
s ool
ld
d ssh
ho
ou
ul
ld
d oon
nl
ly
y bbe
e uus
se
ed
d iin
n aan
n
e em
me
er
rg
ge
en
nc
cy
y aan
nd
d tth
he
en
n wwi
it
th
h aa ppa
ar
rt
ti
ic
cu
ul
la
ar
rl
ly
y cca
ar
re
ef
fu
ul
l sst
ty
yl
le
e oof
f ddr
ri
iv
vi
in
ng
g.
.
W
WA
AR
RN
NI
IN
NG
G
•F Fo
or
r tte
ec
ch
hn
ni
ic
ca
al
l rre
ea
as
so
on
ns
s iit
t iis
s nno
ot
t nno
or
rm
ma
al
ll
ly
y ppo
os
ss
si
ib
bl
le
e tto
o uus
se
e wwh
he
ee
el
ls
s ffr
ro
om
m oot
th
he
er
r
v ve
eh
hi
ic
cl
le
es
s –– iin
n cce
er
rt
ta
ai
in
n cci
ir
rc
cu
um
ms
st
ta
an
nc
ce
es
s nno
ot
t eev
ve
en
n wwh
he
ee
el
ls
s ffr
ro
om
m tth
he
e ssa
am
me
e vve
eh
hi
ic
cl
le
e
m mo
od
de
el
l!
!
W
WA
AR
RN
NI
IN
NG
G
•U Us
si
in
ng
g tty
yp
pe
es
s oof
f wwh
he
ee
el
l aan
nd
d/
/o
or
r tty
yr
re
es
s wwh
hi
ic
ch
h hha
av
ve
e nno
ot
t bbe
ee
en
n aap
pp
pr
ro
ov
ve
ed
d bby
y uus
s
f fo
or
r yyo
ou
ur
r vve
eh
hi
ic
cl
le
e mmo
od
de
el
l cca
an
n bbe
e dde
et
tr
ri
im
me
en
nt
ta
al
l tto
o tth
he
e ssa
af
fe
et
ty
y oof
f tth
he
e vve
eh
hi
ic
cl
le
e.
. IIt
t cca
an
n
a al
ls
so
o aaf
ff
fe
ec
ct
t tth
he
e vve
eh
hi
ic
cl
le
e uun
nd
de
er
r tth
he
e CCo
on
ns
st
tr
ru
uc
ct
ti
io
on
n aan
nd
d UUs
se
e rre
eg
gu
ul
la
at
ti
io
on
ns
s.
.
•W
Wh
he
ee
el
ls
s aan
nd
d wwh
he
ee
el
l bbo
ol
lt
ts
s aar
re
e mma
at
tc
ch
he
ed
d tto
o eea
ac
ch
h oot
th
he
er
r.
.
T Th
he
er
re
ef
fo
or
re
e,
, wwh
he
en
ne
ev
ve
er
r wwh
he
ee
el
ls
s aar
re
e cch
ha
an
ng
ge
ed
d tto
o aa ddi
if
ff
fe
er
re
en
nt
t vve
er
rs
si
io
on
n ((e
e.
.g
g.
. aal
ll
lo
oy
y
w wh
he
ee
el
ls
s oor
r wwh
he
ee
el
ls
s wwi
it
th
h wwi
in
nt
te
er
r tty
yr
re
es
s)
),
, tth
he
e cco
or
rr
re
es
sp
po
on
nd
di
in
ng
g wwh
he
ee
el
l bbo
ol
lt
ts
s wwi
it
th
h tth
he
e
c co
or
rr
re
es
sp
po
on
nd
di
in
ng
g lle
en
ng
gt
th
h aan
nd
d tta
ap
pe
er
r,
, mmu
us
st
t aal
ls
so
o bbe
e uus
se
ed
d.
. TTh
he
e sse
ec
cu
ur
ri
it
ty
y oof
f tth
he
e
w wh
he
ee
el
ls
s aan
nd
d tth
he
e ffu
un
nc
ct
ti
io
on
ni
in
ng
g oof
f tth
he
e bbr
ra
ak
ke
e ssy
ys
st
te
em
m dde
ep
pe
en
nd
d oon
n tth
hi
is
s!
!
•I
If
f wwh
he
ee
el
l ttr
ri
im
m ddi
is
sc
cs
s aar
re
e ssu
ub
bs
se
eq
qu
ue
en
nt
tl
ly
y iin
ns
st
ta
al
ll
le
ed
d iit
t iis
s ees
ss
se
en
nt
ti
ia
al
l tto
o een
ns
su
ur
re
e tth
ha
at
t
t th
he
e aai
ir
r ffl
lo
ow
w rre
em
ma
ai
in
ns
s aad
de
eq
qu
ua
at
te
e tto
o cco
oo
ol
l tth
he
e bbr
ra
ak
ke
es
s.
.
W
WA
AR
RN
NI
IN
NG
G ((c
co
on
nt
ti
in
nu
ue
ed
d)
)

211 If and when
Safety FirstControls and equipment Tips and Maintenance Technical Data
F
Fo
or
r tth
hi
is
s rre
ea
as
so
on
n,
, iin
n sso
om
me
e cco
ou
un
nt
tr
ri
ie
es
s,
, vve
eh
hi
ic
cl
le
es
s wwh
hi
ic
ch
h cca
an
n eex
xc
ce
ee
ed
d tth
hi
is
s
s sp
pe
ee
ed
d mmu
us
st
t hha
av
ve
e aan
n aap
pp
pr
ro
op
pr
ri
ia
at
te
e sst
ti
ic
ck
ke
er
r iin
n tth
he
e ddr
ri
iv
ve
er
r’
’s
s ffi
ie
el
ld
d oof
f
v vi
ie
ew
w.
. TTh
he
es
se
e aar
re
e aav
va
ai
il
la
ab
bl
le
e ffr
ro
om
m TTe
ec
ch
hn
ni
ic
ca
al
l SSe
er
rv
vi
ic
ce
e CCe
en
nt
tr
re
es
s.
.
Please note regulations to this effect in your country.
• All-weather tyres can also be used instead of winter tyres.
• If you have a flat tyre the remarks on using the spare wheel on
page 208 should be noted.
• Do not leave winter tyres fitted for an unnecessary long period
because when the roads are free of snow and ice the handling with
summer tyres is better.
F Fo
or
r tth
he
e ssa
ak
ke
e oof
f tth
he
e een
nv
vi
ir
ro
on
nm
me
en
nt
t
For environmental reasons summer tyres should be fitted again as soon as
possible because normally they are quieter in running, tyre wear is reduced
and the fuel consumption is lower.
K
Snow chains
Snow chains may only be fitted on the front wheels. This also
applies to vehicles with four wheel drive*.
The use of snow chains on the tyres 195/65 R 15 is allowed.
O On
nl
ly
y uus
se
e tth
hi
in
n cch
ha
ai
in
ns
s wwh
hi
ic
ch
h ddo
o nno
ot
t sst
ta
an
nd
d ccl
le
ea
ar
r mmo
or
re
e tth
ha
an
n 115
5 mmm
m
( (i
in
nc
cl
lu
ud
di
in
ng
g tte
en
ns
si
io
on
ne
er
r)
).
.
When using snow chains wheel rim plates and rim rings must be
taken off. In this case, to protect the wheel, the bolts must then be
fitted with caps which are available from Technical Service Centres.When driving over roadswhich are free of snow you must remove
the chains. On such roadsthey are detrimental to vehicle handling,
damage the tyres and wear out quickly.
In some countries the maximum permissible speed with snow
chains is 50 km/h.
K
C Ch
ha
an
ng
gi
in
ng
g wwh
he
ee
el
ls
s
Preparation work
• • IIn
n cca
as
se
e oof
f aa ffl
la
at
t tty
yr
re
e oor
r ppu
un
nc
ct
tu
ur
re
e,
, ppa
ar
rk
k tth
he
e vve
eh
hi
ic
cl
le
e aas
s ffa
ar
r aas
s ppo
os
ss
si
ib
bl
le
e aaw
wa
ay
y
f fr
ro
om
m tth
he
e ttr
ra
af
ff
fi
ic
c ffl
lo
ow
w.
. IIf
f nne
ec
ce
es
ss
sa
ar
ry
y,
, ssw
wi
it
tc
ch
h hha
az
za
ar
rd
d wwa
ar
rn
ni
in
ng
g lli
ig
gh
ht
ts
s oon
n aan
nd
d
p pl
la
ac
ce
e tth
he
e wwa
ar
rn
ni
in
ng
g ttr
ri
ia
an
ng
gl
le
e iin
n ppo
os
si
it
ti
io
on
n –– nno
ot
te
e aan
ny
y sst
ta
at
tu
ut
to
or
ry
y rre
eq
qu
ui
ir
re
em
me
en
nt
ts
s.
.
• • AAl
ll
l vve
eh
hi
ic
cl
le
e ooc
cc
cu
up
pa
an
nt
ts
s ssh
ho
ou
ul
ld
d lle
ea
av
ve
e tth
he
e vve
eh
hi
ic
cl
le
e aan
nd
d mmo
ov
ve
e tto
o aa ssa
af
fe
e aar
re
ea
a
( (e
e.
.g
g.
. bbe
eh
hi
in
nd
d ssa
af
fe
et
ty
y bba
ar
rr
ri
ie
er
r)
).
.
• • PPu
ul
ll
l hha
an
nd
db
br
ra
ak
ke
e ffi
ir
rm
ml
ly
y,
, een
ng
ga
ag
ge
e aa gge
ea
ar
r oor
r een
ng
ga
ag
ge
e sse
el
le
ec
ct
to
or
r lle
ev
ve
er
r iin
n tth
he
e ""P
P"
"
p po
os
si
it
ti
io
on
n aan
nd
d cch
ho
oc
ck
k oop
pp
po
os
si
it
te
e wwh
he
ee
el
l wwi
it
th
h aa sst
to
on
ne
e oor
r ssi
im
mi
il
la
ar
r.
.
• • IIn
n cca
as
se
e yyo
ou
u tto
ow
w aa ttr
ra
ai
il
le
er
r uun
nh
ho
oo
ok
k ttr
ra
ai
il
le
er
r ffr
ro
om
m ttr
ra
ac
ct
to
or
r vve
eh
hi
ic
cl
le
e bbe
ef
fo
or
re
e
c ch
ha
an
ng
gi
in
ng
g tth
he
e wwh
he
ee
el
ls
s.
.
W
WA
AR
RN
NI
IN
NG
G


213 If and when
Safety FirstControls and equipment Tips and Maintenance Technical Data
• Depressions under vehicle for jack:
– Depressions in the side member at front and rear indicate the
points at which the claw of jack must be fitted to the vertical rib of
the side member
⇒arrows,fig. 177.
– Wind jack arm up by turning the crank in the spindle until the
jack just goes under the vehicle.
– The claw of the jack must fit round the vertical rib on the side
member so that the jack cannot slip when vehicle is lifted
⇒
fig. 178.– If the ground is soft, place a large strong piece of packing under
the jack base plate.
– Align jack and at same time wind claw up further until it contacts
the vehicle.
– Lift vehicle until the wheel is just clear of the ground.
K
Removing and fitting the wheel
– Remove the wheel bolts, place them on a clean surface (hub cap,
cloth) next to the jack and take the wheel off.
– Fit spare wheel and lightly tighten all bolts. The wheel bolts must
be clean and easy to turn – do not under any circumstances use
grease or oil!
– Lower vehicle and fully tighten bolts in diagonal sequence.
– Refit the wheel trim.
– Place and secure the defective wheel in the spare wheel bracket
⇒"Spare wheel" chapter.
N No
ot
te
e
•
• TTh
he
e ffo
ol
ll
lo
ow
wi
in
ng
g ppo
oi
in
nt
ts
s ssh
ho
ou
ul
ld
d bbe
e nno
ot
te
ed
d aaf
ft
te
er
r cch
ha
an
ng
gi
in
ng
g aa wwh
he
ee
el
l:
:
– – CCh
he
ec
ck
k tth
he
e iin
nf
fl
la
at
ti
io
on
n ppr
re
es
ss
su
ur
re
e oof
f tth
he
e rre
ep
pl
la
ac
ce
em
me
en
nt
t wwh
he
ee
el
l aas
s sso
oo
on
n aas
s
p po
os
ss
si
ib
bl
le
e.
.
– – HHa
av
ve
e tth
he
e tti
ig
gh
ht
te
en
ni
in
ng
g tto
or
rq
qu
ue
e oof
f tth
he
e wwh
he
ee
el
l bbo
ol
lt
ts
s cch
he
ec
ck
ke
ed
d wwi
it
th
h aa tto
or
rq
qu
ue
e
w wr
re
en
nc
ch
h aas
s qqu
ui
ic
ck
kl
ly
y aas
s ppo
os
ss
si
ib
bl
le
e.
. TTh
he
e tto
or
rq
qu
ue
e ffo
or
r sst
te
ee
el
l aan
nd
d aal
ll
lo
oy
y wwh
he
ee
el
ls
s iis
s
1 17
70
0 NNm
m.
.
I If
f tth
he
e wwh
he
ee
el
l bbo
ol
lt
ts
s aar
re
e sse
ee
en
n tto
o bbe
e cco
or
rr
ro
od
de
ed
d oor
r tto
oo
o tti
ig
gh
ht
t wwh
he
en
n cch
ha
an
ng
gi
in
ng
g tth
he
e
w wh
he
ee
el
l,
, tth
he
ey
y mmu
us
st
t bbe
e rre
ep
pl
la
ac
ce
ed
d bbe
ef
fo
or
re
e cch
he
ec
ck
ki
in
ng
g tth
he
e tto
or
rq
qu
ue
e.
.
U Un
nt
ti
il
l tth
hi
is
s hha
as
s bbe
ee
en
n ddo
on
ne
e,
, yyo
ou
u ssh
ho
ou
ul
ld
d oon
nl
ly
y ddr
ri
iv
ve
e aat
t llo
ow
w ssp
pe
ee
ed
ds
s.
.

Fig. 178AL0-138
I If
f tth
he
e jja
ac
ck
k iis
s nno
ot
t ffi
it
tt
te
ed
d aat
t tth
he
e ppo
oi
in
nt
ts
s mma
ar
rk
ke
ed
d oor
r dde
es
sc
cr
ri
ib
be
ed
d,
, dda
am
ma
ag
ge
e cco
ou
ul
ld
d bbe
e
c ca
au
us
se
ed
d tto
o tth
he
e vve
eh
hi
ic
cl
le
e.
. TTh
he
er
re
e iis
s aal
ls
so
o aa rri
is
sk
k oof
f iin
nj
ju
ur
ry
y!
!
W
WA
AR
RN
NI
IN
NG
G

215 If and when
Safety FirstControls and equipment Tips and Maintenance Technical Data
The Alhambra’s alloy wheels have anti-theft wheel bolts. The
special adapter required for these bolts is contained in the vehicle
tool kit.
The procedure for changing a wheel is as follows:
• First press the adapter
2as far as possible into the star shaped
depression on the anti-theft wheel bolt1⇒ fig. 179.
• Push the wheel spanner (from the vehicle tools) as far as
possible onto the adapter
2and loosen/tighten the wheel bolt as
necessary
⇒"Replacing a wheel" chapter.
N No
ot
te
e
• We recommend always carrying the adaptor in the space provided for it in
the tool box⇒fig. 180
• Should you lose the adapter
⇒fig. 1792, SEAT Service can supply you
with a new one with reference to the code card (also in vehicle tools).
Y Yo
ou
u ssh
ho
ou
ul
ld
d kke
ee
ep
p tth
he
e cco
od
de
e cca
ar
rd
d iin
n aa ssa
af
fe
e ppl
la
ac
ce
e –– oon
n nno
o aac
cc
co
ou
un
nt
t ssh
ho
ou
ul
ld
d iit
t bbe
e
l le
ef
ft
t iin
n tth
he
e vve
eh
hi
ic
cl
le
e.
. AA rre
ep
pl
la
ac
ce
em
me
en
nt
t aad
da
ap
pt
te
er
r cca
an
n oon
nl
ly
y bbe
e ssu
up
pp
pl
li
ie
ed
d uus
si
in
ng
g tth
hi
is
s
c co
od
de
e cca
ar
rd
d.
.
K
F
Fu
us
se
es
s
The individual current circuits are protected by fuses.
All electric windows are protected together via an automatic fuse
which breaks the circuit when overloaded (e.g. windows frozen)
and completes the circuit again after a few seconds.
It is advisable to always carry a few spare fuses on the vehicle.
Fuse colour code
K
N Ne
ev
ve
er
r,
, uun
nd
de
er
r aan
ny
y cci
ir
rc
cu
um
ms
st
ta
an
nc
ce
es
s ““r
re
ep
pa
ai
ir
r”
” tth
he
e ffu
us
se
es
s oor
r rre
ep
pl
la
ac
ce
e tth
he
em
m wwi
it
th
h
m mo
or
re
e ppo
ow
we
er
rf
fu
ul
l oon
ne
es
s,
, aas
s dda
am
ma
ag
ge
e iin
n aan
no
ot
th
he
er
r ppa
ar
rt
t oof
f tth
he
e eel
le
ec
ct
tr
ri
ic
ca
al
l ssy
ys
st
te
em
m
c co
ou
ul
ld
d ooc
cc
cu
ur
r.
. TTh
hi
is
s cco
ou
ul
ld
d eev
ve
en
n lle
ea
ad
d tto
o aa ffi
ir
re
e.
.
K
W WA
AR
RN
NI
IN
NG
G
C Co
ol
lo
ou
ur
rA
Am
mp
pe
er
re
es
s
Purple 3
Beige 5
Brown 7,5
Red 10
Blue 15
Ye l l o w 2 0
White 25
Green 30

217 If and when
Safety FirstControls and equipment Tips and Maintenance Technical Data
K
S
Sy
ym
mb
bo
ol
lM
Me
ea
an
ni
in
ng
g
Fan
Air conditioning
Heating
Heated windshield
Heated rear window
Heated rearview mirrors
Adjustment of outside mirrors
Lowering of outside mirrors
Seat heating
Horn
Windscreen washer/wiper
Rear windscreen washer/wiper
Rear windscreen washer
Headlight washer
Sliding roof
Electric windows
Lighter
Electric side windows
Central locking/Remote control
Electric switchboard
Ignition
S Sy
ym
mb
bo
ol
lM
Me
ea
an
ni
in
ng
g
Diagnosis
ABS
ESP
Selector lever positions (in display)
Electronic immobilizer
License plate lighting
Heated ejectors
Instrument panel
Central locking
Radio
CD changer/player
Telephone/telematic function*
Mobile telephone
Cruise control
Radio navigation system
Interior lighting
Reading light
Fuel pump
Trailer light connection
Parking assistance

219 If and when
Safety FirstControls and equipment Tips and Maintenance Technical Data
• Press turn signal to front⇒fig. 182 arrow 1and remove ⇒
fig. 182 arrow 2.
• Remove the bulb carrier and disconnect it.
• Pull out defective glass based bulb and insert new bulb.
• Insert the bulb carrier into the indicator covers.
• First place turn signal with retaining lugs
⇒fig. 184 arrow 1in
body opening and then engage light in direction of arrow
⇒
fig. 182 2.K
Rear lights
Before changing rear light bulbs the boot lid must be opened.
The bulbs are arranged as follows.
I In
n tth
he
e bbo
od
dy
y
Turn signal, tail light and brake/tail light.
I In
n tta
ai
il
lg
ga
at
te
e oor
r bbo
oo
ot
t lli
id
d
Reversing light and rear fog light.
K
Lights in the body
• Open flap in the luggage compartment trim.
• Press sidepiece in the direction of the arrow.
1
2AL0-142Fig. 184
Fig. 185AL0-066


221 If and when
Safety FirstControls and equipment Tips and Maintenance Technical Data
Number plate light
• Unscrew lens.
• Pull defective glass based bulb out of bulb holder and insert new
bulb.
• Do not overtighten lens. Ensure that the seals are properly
located.
• Insert lens in the tailgate opening, ensure that the rubber seal
and the light are correctly positioned (see adjacent light).
• Do not overtighten the lens screws.
K
Interior light
• Insert a knife or similar in the gap between housing and lens
(arrow) and carefully lever lens off.
• Exchange bulb.
• Press lens back into housing.
K
Fig. 188Fig. 189B7M-0018AL0-062