Seat Alhambra 2010 Owner's Manual

Checking and refilling levels 310
Engine oil specifications
Replacement engine oil must strictly comply with the specifications.
The correct oil must be used to ensure the correct operation and long service
life of the engine. The engine comes with a high-quality multigrade oil that
can generally be used all year round.
Only use an oil that complies to SEAT standards whenever possible Ÿ. If
you wish to maintain the long-life service duration, only engine oils approved
for this service according to the corresponding VW standard (Ÿtable on
page 310) may be used. All oils indicated are synthetic multigrade oils.
Engine oils are being continuously further developed. Qualified workshops
are permanently informed of any modifications. SEAT therefore recommends
that you have the engine oil changed by a SEAT Dealership.
Caution
xOnly use engine oils whose specifications are expressly approved by
SEAT. The use of any other type of engine oil could cause engine damage!
xNo additives should be used with engine oil. Any damage caused by the
use of such additives would not be covered by the factory warranty.
Checking the engine oil level and topping up
Preparations
xPark the vehicle on flat ground so that the engine oil reading is correct.
EnginesEngine oil specifications
with LongLife servicewithout LongLife service
Petrol enginesVW 504 00, VW 503 00VW 504 00, VW 502 00
Diesel enginesVW 507 00VW 507 00
Fig. 175 Marked engine
oil dipstick.
Fig. 176 In the engine
compartment: Engine oil
filler cap.

Checking and refilling levels311
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xStop the engine and wait a few minutes for the oil to drain back into the
sump. When the engine has cooled down, immediately check the oil level and
top up if necessary.
xOpen the bonnet ’ Ÿpage 304.
xThe engine oil filler opening can be recognised by the symbol E on the
cap Ÿpage 310, fig. 176 and the dipstick by its coloured handle.
Checking the engine oil level
xPull out the dipstick and wipe it on a clean cloth.
xReplace the dipstick, pushing it in as far as it will go. If the dipstick has a
mark, when you reintroduce it this mark should slot into the corresponding
groove located on the upper end of the tube.
xRemove the dipstick again and check the engine oil level Ÿtable on
page 311.
xAfter reading the oil level, replace the dipstick in the tube completely.
Engine oil topping up ranges
Adding oil after checking the level
Only add engine oil in small quantities and in steps.
xUnscrew the cap from engine oil filler opening on the cylinder head
Ÿpage 310, fig. 176. If you are not sure where the cap is, request help from
a specialist.
xOnly refill using engine oil expressly approved by SEAT and in small quan-
tities (not more than 0.5 L or 1/2 a quarter of a gallon at a time) Ÿpage 310.
xTo avoid adding too much oil, each time you add a quantity, wait until the
oil has flowed into the crankcase so that it can be measured with the dipstick.
xCheck the oil level before adding any more oil. Do not top up with too
much engine oil Ÿ.
xWhen the oil level is in at least the Ÿpage 310, fig. 175 zone, insert
the dipstick into the tube fully to avoid engine oil escaping when the engine
is running.
xAfter topping up the oil, ensure that the cap is screwed on to the filler
mouth correctly.
WARNING
Oil could catch fire if it comes into contact with hot engine components.
This could lead to a fire, explosion and severe injuries.
xAlways ensure that after topping of oil, the engine oil filler cap is
correctly tightened. This will avoid engine oil spilling onto hot engine parts
when the engine is running.
Caution
xIf the oil level is above the area Ÿpage 310, fig. 175 do not start the
engine. You should obtain professional assistance. Otherwise catalytic
converter and engine damage may occur.
xWhen refilling or changing service liquids, ensure that you put the liquids
into the right tank. Making a mistake when refilling could cause serious
malfunctions and damage the engine!
For the sake of the environment
The oil level must never be above area Ÿpage 310, fig. 175 . Otherwise
oil can be drawn in through the crankcase breather and escape into the
atmosphere via the exhaust system.
page 310,
fig. 175Operations required depending on the engine oil topping
up level:
Area Do not top up oil Ÿ.
Area Add approximately 0.5 L of oil (1/2 quarter of a gallon). The
oil level can be in the zone , but never above .
Area :
It is essential to add oil (approximately 1 litre or quarter of
a gallon). Ensure that the level is around the centre of the
zone after adding oil.
AA
ABAAAA
ACAB
AB
AA
AA

Checking and refilling levels 312
Engine oil consumption
The consumption of engine oil can be different from one engine to another
and can vary during the useful life of the engine.
Depending on driving style and the conditions of use, the consumption of
engine oil can reach 1 litre every 2,000 km (one quarter of a gallon every
1,200 miles); for new vehicles, this could be higher for the first 5,000 km
(3,000 miles). For this reason the engine oil level must be checked at regular
intervals, preferably when filling the tank and before a journey.
When the engine is working hard, for instance during sustained high-speed
motorway cruising in summer, when towing a trailer or climbing mountain
passes, the oil level should preferably be kept within area Ÿpage 310,
fig. 175 .
Changing the engine oil
The engine oil must be changed regularly according to the specifications of
the Maintenance Programme.
Due to the problems linked with disposing of used oil and the need for suit-
able tools and special knowledge, always visit a qualified workshop to have
the engine oil and filter changed. SEAT recommends visiting a qualified work-
shop.
Detailed information on the service intervals are shown in the Maintenance
Programme.
Engine oil additives make new oil darker after the engine has been running
for a short period. This is normal and does not mean more frequent oil
changes are required.
WARNING
If, in exceptional circumstances, you must change the engine oil yourself,
please note the following:
xWear eye protection.
xAlways wait until the engine has completely cooled to avoid being
burned.
xAlways keep your arms horizontal when unscrewing the oil drainage
bolt so that the oil does not run down your arms when it begins to drain.
xUse a suitable and large enough container to collect all of the used oil
in the engine.
xNever collect engine oil in empty food containers, cans, bottles and
other containers as not all people are able to identify engine oil.
xOil is toxic and must be kept out of the reach of children.
For the sake of the environment
Before changing the engine oil, find a suitable location or service for proper
disposal.
For the sake of the environment
Always dispose of engine oil with the utmost respect for the environment.
Never dispose of used engine oil in places such as a garden, woods, drains,
roads, paths, rivers and drainage systems.
AA

Checking and refilling levels313
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Engine coolant
Introduction
Never work on the engine cooling system or if you are not familiar with the
operations to be carried out, the applicable safety standards and especially
if you do not have the instruments, liquids and tools necessary Ÿ! Have
the work carried out by a qualified workshop if you are uncertain. SEAT recom-
mends visiting a qualified workshop.
Negligent work can cause serious injury.
Additional information and warnings:
xTo wi ng m o d e Ÿpage 260
xWorking in the engine compartment Ÿpage 304
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Engine coolant is toxic!
xOnly keep engine coolant in its original container, tightly shut and in a
safe place.
xNever store engine coolant in empty food containers or bottles as other
people may accidentally drink it.
xAlways keep engine coolant out of reach of children.
xEnsure that the proportion of engine coolant additive corresponds to
the lowest outside temperature to which the vehicle will be exposed.
xIf the outside temperature is extremely low, the engine coolant could
freeze causing the vehicle to stop. As this would also cause the heating to
stop working, passengers without sufficient clothing could freeze.
For the sake of the environment
Coolants and additives can contaminate the environment. Collect any spilt
fluids in suitable containers and dispose of in accordance with legislation
and with the utmost respect for the environment.
Coolant temperature warning lamp and gauge
When driving normally, the needle will remain in the middle area. The temper-
ature may also rise when the engine is working hard, especially at high
outside temperatures and so the indicator will move quite far to the right-
hand side.
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
Fig. 177 Engine coolant
temperature gauge on the
instrument panel: cold
area; normal area;
warning area.
AAABAC

Checking and refilling levels 314
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xAlways observe any lit warning lamps and text messages.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
Engine coolant specifications
The engine cooling system comes with a special mixture of water and at least
40% G 12 plus-plus (TL-VW 774 G) or G 12 plus (TL-VW 774 F) engine coolant
additive. Both are easily recognisable because they are purple in colour.
This mixture gives the necessary frost protection down to -25 °C (-13 °F) and
protects the alloy parts of the cooling system against corrosion. It also
prevents scaling and raises the boiling point of the coolant.
To protect the engine cooling system, the proportion of additive must always
be at least 40%, even if frost protection is not required in countries with a
warm climate.
If greater frost protection is required in very cold climates, the proportion of
additive can be increased. However, the percentage of additive should not
exceed 60 %, as this would reduce the frost protection and, in turn, decrease
the cooling capacity.
When adding coolant, a mixture of distilled water and at least 40 % of the
additive G 12 plus-plus must be use to ensure optimum rust protection Ÿ.
lights up
Gauge
position
Ÿpage 31
3, fig. 177
Possible causeSolution
v
Warning
area Excessive engine
coolant tempera-
ture.
› Stop the vehicle!
Stop the vehicle safely as
soon as possible. Switch off
the engine and wait for it to
cool down and for the needle
to return to the normal area.
Check the engine coolant level
Ÿpage 315.
Normal
area Insufficient engine
coolant level.
Check the engine coolant
when the engine has cooled
and, if it is low, refill with
engine coolant Ÿpage 315.
Although the coolant level is
correct, there is a fault.
--Engine coolant
system faulty.› Do not drive any further.
Obtain professional assist-
ance.
--
Cold area

--
Avoid revving the engine too
much or making it work hard
while it has not reached nor-
mal service temperature.
flashesPossible causeSolution
vEngine coolant system faulty.You should obtain profes-
sional assistance.
AC
AB
AA

Checking and refilling levels315
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
WARNING
In the event of insufficient antifreeze protection in the engine cooling
system, the engine could be damaged and severe injuries caused.
xEnsure that the proportion of engine coolant additive corresponds to
the lowest outside temperature to which the vehicle will be exposed.
xIf the outside temperature is extremely low, the engine coolant could
freeze causing the vehicle to stop. As this would also cause the heating to
stop working, passengers without sufficient clothing could freeze.
Caution
Never mix genuine additives with other additives that are not approved by
SEAT. Otherwise, you run the risk of causing severe damage to the engine and
the engine cooling system.
xThe engine coolant G 12 plus-plus can be mixed with G 12 plus and G 11.
xIf the fluid in the expansion reservoir is not purple but, for example,
brown, this means that you have mixed G 12 plus-plus or G 12 plus with
another coolant. The coolant must be changed as soon as possible if this is
the case! Failure to observe this point will result in serious malfunctions and
engine damage!
For the sake of the environment
Coolants and additives can contaminate the environment. Collect any spilt
fluids in suitable containers and dispose of in accordance with legislation
and with the utmost respect for the environment.
Checking the engine coolant level and refilling
If the coolant level is low, the coolant warning indicator will light.
Fig. 178 In the engine
compartment: Marking on
coolant expansion reser-
voir.
Fig. 179 In the engine
compartment: Coolant
expansion tank cap.

Checking and refilling levels 316
Preparations
xPark the vehicle on even, flat and firm ground.
xAllow the engine to cool Ÿ.
xOpen the bonnet ’ Ÿpage 304.
xThe coolant expansion reservoir is easily recognisable because of the
symbol « on the cap Ÿpage 315, fig. 179.
Checking the engine coolant level
xWhen the engine is cold, check the coolant level using the side marking
on the expansion reservoir Ÿpage 315, fig. 178.
xIf the level is below the “MIN” mark, top up with coolant. When the engine
is hot it may be slightly above the marked area.
Topping up the engine coolant level
xAlways protect your face, hands and arms from hot coolant and steam
using a large, thick cloth over the coolant expansion tank cap.
xRemove the cap very carefully Ÿ.
xOnly refill using new engine coolant according to SEAT specifications
(Ÿpage 314) Ÿ.
xThe engine coolant level should be between the marks on the coolant
expansion tank Ÿpage 315, fig. 178. Do not exceed the top level of the
marked area Ÿ.
xScrew on the cap tightly.
xIf, the event of an emergency, you have no coolant that is compliant to the
required specifications (Ÿpage 314), never use another type of additive.
Instead, first top up with distilled water Ÿ only. Then re-establish the
correct proportion of the mixture with the correct additive as soon as possible
Ÿpage 314.
WARNING
Hot vapours and coolant can cause serious burns.
xNever open the coolant expansion tank if steam or coolant is coming
from the engine compartment. Wait until you cannot see or hear any steam
or coolant escaping.
xAlways wait until the engine has completely cooled before very care-
fully opening the expansion tank cap. Contact with hot elements of the
engine can cause skin burns.
xOnce the engine has cooled, follow the instructions below before
opening the bonnet:
Turn on the electronic parking brake and place the gear selector lever
in P or the gear stick in neutral.
Remove the key from the ignition.
Keep children away from the engine compartment and never leave
them unsupervised.
xWhen the engine is warm or hot, the cooling system is pressurised! Do
not unscrew the cap on the expansion tank when the engine is hot. Other-
wise, coolant may spray out under pressure causing burns and serious
injury.
Carefully and slowly unscrew the cap anticlockwise, gently pressing
down on it.
Always protect your face, hands and arms from hot coolant and
steam using a large, thick cloth.
xWhen refilling liquids, avoid spilling them on parts of the engine and
the exhaust system. Spilled liquids could cause a fire. Under specific
circumstances, the ethylene glycol can catch fire.
Caution
xTop up with distilled water only. Any other type of water may lead to
considerable rusting in the engine due to its chemical components. This
could consequently damage the engine. If you have not used distilled water
WARNING (continued)

Checking and refilling levels317
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a but another type of water to top up the coolant, a specialist workshop must
immediately replace all of the fluid in the engine cooling system.
xOnly top up coolant to the top level of the marked area Ÿpage 315,
fig. 178. Otherwise the excess coolant will be forced out of the cooling system
when the engine is hot, causing damage.
xIf a lot of liquid coolant has been lost, wait for the engine to cool down
completely before adding coolant. Extensive coolant loss is an indication of
leaks in the engine cooling system. Have the engine cooling system
inspected immediately by a qualified workshop. Otherwise you may damage
the engine.
xWhen refilling or changing service liquids, ensure that you put the liquids
into the right tank. Making a mistake when refilling could cause serious
malfunctions and damage the engine!

Checking and refilling levels 318
Vehicle batter y
Introduction
The battery is a component of the vehicle's electrical system.
Never work on the electrical system without fully understanding the opera-
tions required, the applicable safety standards and without the correct tools
Ÿ! Have the work carried out by a qualified workshop if you are uncertain.
SEAT recommends visiting a qualified workshop. Negligent work can cause
serious injury.
Location and number of batteries in the vehicle
The battery is located in the engine compartment.
Explanation of the warning indications on the vehicle's battery
Additional information and warnings:
xŸBooklet “Maintenance Programme”
xStarter assist systems (Start-Stop function) Ÿpage 221
xWorking in the engine compartment Ÿpage 304
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Working on the vehicle battery and the electrical system can cause corro-
sion, fire and electric shocks. Always read and take into account the
following warnings and safety standards before carrying out any work:
xBefore working on the battery, switch off the engine, the ignition and
all electrical devices then disconnect the negative connection on the
battery.
xKeep children away from acid and the battery itself!
xWear eye protection.
xBattery acid is very corrosive and caustic. It can burn skin and cause
blindness. When handling the battery, protect yourself from splashes of
acids, above all your hands, arms and face.
xDo not smoke and never work close to places exposed to flames or
sparks.
xAvoid sparks and electrostatic discharges when working with cables
and electrical devices.
xNever short the battery terminals.
xNever use a damaged battery. It can explode. Replace a damaged
battery immediately.
xReplaced damaged or frozen batteries as soon as possible. A flat
battery can freeze at temperatures around 0°C (+32 °F).
xVehicles with the battery in the luggage compartment: Ensure that the
battery ventilation hose is correctly secured.
Caution
xNever disconnect the battery if the ignition is switched on or if the engine
is running. This could damage the electrical system or electronic compo-
nents.
SymbolMeaning
Wear eye protection!
Battery acid is very corrosive and caustic. Always wear
protective gloves and eye protection!
ŽFires, sparks, naked lights and smoking are prohibited.
ŸA highly explosive mixture of gases is released when the
battery is under charge.
Keep children away from acid and batteries!

Checking and refilling levels319
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xDo not expose the battery to direct sunlight over a long period of time, as
the intense ultraviolet radiation can damage the battery housing.
xIf the car is left standing for long periods, protect the battery from extreme
cold temperature so that it does not “freeze up” and become damaged.
Warning lamp
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
WARNING
If the warning lamps and messages are ignored, the vehicle may stall in
traffic, or may cause accidents and severe injuries.
xNever ignore the warning lamps or text messages.
xStop the vehicle safely as soon as possible.
Caution
Failure to heed the warning lamps and text messages when they appear may
result in faults in the vehicle.
Checking the electrolyte level of the vehicle battery
The battery's electrolyte level should be checked regularly in high-mileage
vehicles, in hot countries and in older batteries. Other batteries do not
require maintenance.
lights upPossible causeSolution
FFaulty generator.
Contact a specialist workshop.
Have the electrical system
checked.
Disconnect any unnecessary
electrical consumers. The gener-
ator does not charge the battery
while the vehicle is in motion.
Fig. 180 In the engine
compartment: Remove
the cover from the
vehicle's battery.
Fig. 181 In the engine
compartment: Unfold the
vehicle's battery hose.