heating Seat Alhambra 2010 Service Manual

Page 274 of 413

Vehicle maintenance and cleaning273
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xAerials on the inside of windows may be damaged if knocked or if cleaned
with corrosive or acid cleaning products. Do not stick adhesive labels over the
heating elements and never clean the inside of the rear window with corro-
sive or acid products or other similar chemical cleaning products.
Cleaning and changing windscreen wiper blades
The windscreen wiper blades are supplied as standard with a layer of
graphite. This layer is responsible for ensuring that the wipe is silent. If the
graphite layer is damaged, the noise of the water as it is wiped across the
windscreen will be louder.
Check the condition of the wiper blades regularly. If the wipers scrape across
the glass they should be changed if they are damaged, or cleaned if they are
dirty Ÿ.
Damaged wiper blades should be replaced immediately. Blades are available
from qualified workshops.
Lifting and unfolding the wiper arms
The wiper arm may only be lifted at the point where it is fastened to the blade.
For windscreen wipers, please note: the wiper should be in service position
before unfolding it Ÿpage 124.
Cleaning windscreen wiper blades
xLifting and unfolding the wiper arms.
xUse a soft cloth to remove dust and dirt from the windscreen wiper blades.
Fig. 165 Changing the
front wiper blades
Fig. 166 Changing the
rear wiper blade.

Page 277 of 413

Vehicle maintenance and cleaning 276
Before applying the product, use a soft cloth to remove dust and dirt from the
rubber seals.
De-icing the door lock cylinder
To de-ice the lock cylinders, SEAT recommend the use of genuine SEAT spray
with lubricating and anti-corrosive properties.
Caution
The use of products containing degreasing agents to de-ice the locks may
rust the lock cylinder.
Protection of vehicle undercarriage
The vehicle underbody is coated to protect it from chemical and mechanical
damage. The protective coat on the undercarriage may wear through use
while driving. Therefore, SEAT recommends that the protective coating on the
undercarriage and on the running gear should be regularly checked, and
repaired if necessary.
WARNING
Additional underseal or anti-corrosion products could catch fire due to the
high temperatures reached by the exhaust gas system and other engine
components.
xDo not apply additional underseal or anti-corrosion products to the
exhaust pipes, catalytic converters, heat shields or other parts of the
vehicle which reach high temperatures.
Cleaning the engine compartment
The engine compartment of any motor vehicle is a potentially hazardous area
Ÿpage 304.
The engine compartment should only be cleaned by qualified personnel. If it
is not correctly cleaned, the anti-corrosion coating and consequently elec-
trical components may be damaged. Moreover, water may filter directly into
the vehicle interior through the water chamber Ÿ.
If the engine compartment is very dirty, always take the vehicle to a qualified
workshop for professional cleaning. SEAT recommends visiting a qualified
workshop.
Water box
The water box is in the engine compartment, between the windscreen and the
engine, and beneath a perforated cover. Air is taken in through the water box
from outside to the vehicle interior via the heating and air conditioning
system.
Leaves and other loose objects should be regularly cleaned away from the
water box either by hand or with a vacuum.
WARNING
When working on the engine or in the engine compartment, there is a risk
of injury, burns, accident or fire.
xBefore starting work, please ensure you are familiar with the required
procedure and the safety precautions Ÿpage 304.
xSEAT recommends you have this work performed by a qualified dealer-
ship.
Caution
If water is manually poured into the water box (for example, using a high pres-
sure cleaning appliance), this could cause significant damage to the vehicle.

Page 284 of 413

Vehicle maintenance and cleaning283
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Notes for the user
Labels and plates
Some parts in the engine compartment come from the factory with certifi-
cates of safety, labels or plates containing important information regarding
the operation of the vehicle, for example, on the petrol cap, on the
passenger's sun visor, on the driver's door strut, or on the floor of the luggage
compartment.
xNever remove these certificates of safety, labels or plates, and ensure
they are kept in good condition and are legible.
xIf a vehicle part, bearing a certificate of safety, label or plate, is replaced,
the qualified workshop should attach the information back in the same place.
Certificate of safety
A certificate of safety on the door strut states that all the safety standards and
regulations established by the national traffic authorities responsible for
road safety were met at the time of manufacture. It may also give the month
and year of manufacture, together with the chassis number.
Warning of high voltage label*
There is a label close to the bonnet lock which warns of high voltage in the
vehicle electrical installation. The vehicle ignition system complies with
several standards, including the Canadian standard, ICES-002.
Using your vehicle in other countries and continents
The vehicle is manufactured at the factory for use in a particular country in
accordance with the national legislation in force at the time of manufacture.If the vehicle is sold in another country or used in another country for an
extended period of time, the applicable legislation of that country should be
observed.
It may be necessary to fit or remove certain pieces of equipment or to deacti-
vate certain functions. Service work may also be affected. This is particularly
true if the vehicle is used in a different climate for an extended period of time.
As there are different types of frequency bands around the world, you may
find that the radio or navigation system supplied at the factory does not work
in another country.
Caution
xSEAT does not accept liability for any damage to the vehicle due to the use
of a lower quality fuel, an inadequate service or the non-availability of
genuine spare parts.
xSEAT does not accept liability if the vehicle does not comply in part or in
full with the legal requirements of other countries or continents.
Radio reception and the aerial
The aerial of radio and navigation systems fitted at the factory may be
mounted in different parts of the vehicle:
xOn the inside of the rear window, next to the rear window heating,
xon the inside of the rear side windows,
xon the inside of the windscreen,
xon the roof of the car.
Aerials mounted on the inside of a window can be recognised by the fine
wires.

Page 285 of 413

Vehicle maintenance and cleaning 284
Caution
Aerials on the inside of windows may be damaged if knocked or if cleaned
with corrosive or acid cleaning products. Do not stick adhesive labels over the
heating elements and never clean the inside of the rear window with corro-
sive or acid products or other similar chemical cleaning products.
Note
If electrical equipment is used near an aerial built-into the window, you may
observe interference in the reception of AM stations.
Notes on SEAT repairs
WARNING
Repairs or modifications which are not performed correctly may result in
damage or errors in the vehicle operation, affecting the efficiency of the
driver assist and airbag systems. This could result in serious accident.
xHave any repairs or modifications carried out at a qualified workshop.
Collection and scrapping of end-of-life vehicles
Collection of end-of-life vehicles
An extensive network of used car reception centres already exists in much of
Europe. After the vehicle has been delivered, you will receive a certificate of
destruction describing the environmentally friendly scrapping of the vehicle
in accordance with applicable legislation.
We will collect the used vehicle free of charge, provided it complies with all
national legislation.Please see your Technical Service for further information about the collection
and scrapping of end-of-life vehicles.
Scrapping
The relevant safety requirements must be observed when the vehicle or
components of the airbag or belt tensioner systems are scrapped. These
requirements are known to qualified dealerships.

Page 294 of 413

Checking and refilling levels293
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Checking and refilling levels
Filling the tank
Introduction
The fuel tank flap is on the rear right of the vehicle.
Additional information and warnings:
xFuel Ÿpage 297
xSelective Catalytic Reduction (AdBlue) Ÿpage 300
xWorking in the engine compartment Ÿpage 304
WARNING
Refuelling or handling fuel carelessly can cause an explosion or fire
resulting in serious burns and injuries.
xAlways make sure that you correctly close the fuel cap to avoid evapo-
ration and fuel spillage.
xFuels are highly explosive and inflammable substances that can cause
serious burns and injuries.
xFuel could leak out or be spilt if the engine is not switched off or if the
filler fuel nozzle is not fully inserted into the tank filler neck when refuel-
ling. This could lead to a fire, explosion and severe injuries.
xWhen refuelling, turn off the engine, the auxiliary heating
(Ÿpage 187) and turn off the ignition for safety reasons.
xAlways turn off mobile telephones, radio apparatus and other radio
wave emitting equipment before refuelling. Electromagnetic waves could
cause sparks and lead to a fire.
xNever enter the vehicle while refuelling. If it is absolutely necessary to
enter the vehicle, close the door and touch a metal surface before touching
the filler nozzle again. This will prevent the generation of static electricity.
Sparks could cause a fire when refuelling.
xNever handle fuel close to open flames, sparks or objects with slow
combustion (e.g. cigarettes).
xAvoid static electricity and electro-magnetic radiation when refuelling.
xObserve the safety regulations of the service station.
xNever spill fuel on the vehicle or in the luggage compartment.
WARNING
For safety reasons, SEAT does not recommend carrying a spare fuel canister
in the vehicle. Fuel could be spilled and catch fire, above all in case of an
accident and this applies to a full container as well as empty containers.
This could lead to explosions, fires and injuries.
xObserve the following if you exceptionally have to carry fuel in a
canister:
Never place a fuel container to fill it inside the vehicle or on the
vehicle, for example, in the luggage compartment or on the tailgate.
Filling in these circumstances could create an electrostatic charge and
spark that could ignite fuel fumes.
Always place the canister on the ground to fill it.
Insert the fuel nozzle into the mouth of the canister as far as
possible.
If you are using a metal fuel canister, the nozzle must always touch
the canister while it is being filled to avoid static electricity.
WARNING (continued)

Page 295 of 413

Checking and refilling levels 294
Follow the legal requirements for the use, storage and transport of
spare fuel canisters.
Insure that the fuel container complies with manufacturing stand-
ards, for example, ANSI or ASTM F852-86.
Caution
xAlways remove any fuel spilled on the vehicle paintwork immediately to
avoid damage to the wheel housing, the tyre and vehicle paintwork.
xRefuelling a petrol engine with diesel or a diesel engine with petrol can
cause serious engine and fuel system damage; the resulting malfunctions
are not covered by the SEAT warranty. If you refuel with the wrong type of fuel,
never start the engine. This applies to even the smallest amount of the wrong
fuel. You should obtain professional assistance. With the engine running, the
composition of the wrong fuel could significantly damage the fuel system and
the engine itself.
xIn vehicles with a diesel engine, under no circumstances should you
refuel or drive with petrol, kerosene, heating oil or any other type of different
fuel. Other types of fuels could cause serious damage to the engine and to
the fuel supply system and the resulting problems are not covered by the
SEAT warranty.
For the sake of the environment
Fuels can contaminate the environment. Collect any spilt service fluids and
allow a professional to dispose of them.
Note
There is no emergency mechanism for the manual release of the tank flap. If
necessary, request assistance from specialised personnel.
Control lamps and fuel gauge
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
The auxiliary heater and the auxiliary heater running off petrol will automati-
cally switch off when the indicator
z or  lights.
WARNING (continued)
lights upGauge position
Ÿfig. 169Possible cause ŸSolution
Red mark
(arrow)
The fuel tank is almost
empty.
The reserve tank is
being used
Ÿpage 392.
Refuel as soon as
possible Ÿ.
§Fuel tank not closed
correctly.Stop the vehicle and
close the tank flap
properly.
Fig. 169 On the instru-
ment panel: Fuel gauge for
petrol and diesel.

Page 296 of 413

Checking and refilling levels295
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
WARNING
Driving with insufficient fuel reserve could result in the vehicle breaking
down in traffic and a serious accident.
xIf the fuel level is too low then the fuel supply to the engine can become
irregular especially on slopes.
xIf the engine “is choked” or stalls due to lack of or irregularity of the
fuel supply, the power steering as well as all of the driver assistance
systems including braking assistance will stop working.
xAlways refuel when there is only one quarter of the fuel tank left to
avoid running out of fuel.
Caution
xAlways pay attention to any lit lamps and to the corresponding descrip-
tions and instructions to avoid damage to the vehicle.
xNever run the tank completely dry. An irregular fuel supply may lead to
ignition faults and unburnt fuel could enter the exhaust system. This could
damage the catalytic converter filter or the diesel particulate filter!
Note
The arrow next to the fuel pump symbol on the instrument panel Ÿpage 294,
fig. 169 indicates the side of the vehicle on which the tank flap is located.
Filling the tank with petrol or diesel
Before refuelling, always turn off the engine, the ignition, mobile telephones,
auxiliary heating and keep them off during refuelling.
Unscrewing the tank cap
xThe tank flap is at the rear of the vehicle on the right.
xPress the rear of the tank flap to open it.
xUnscrew the tank cap anti-clockwise and insert it in the hole in the tank
flap hinge Ÿfig. 170.
Refilling
The correct petrol type for the vehicle is located on a sticker inside the fuel
tank flap Ÿpage 297.
xIf the automatic filler nozzle is operated correctly, it will switch itself off as
soon as the tank is full Ÿ.
xDo not continue to refuel if it is turned off! Otherwise, this will fill the
expansion chamber and fuel may leak out if the ambient conditions are warm.
Fig. 170 Open tank flap
with tank cap attached to
the holder.

Page 299 of 413

Checking and refilling levels 298
If good quality petrol with additives is not available or engine problems arise,
the necessary additives must be added when refuelling.
Not all petrol additives have been shown to be effective. The use of unsuit-
able petrol additives could damage the engine. These additives are available
from qualified workshops, who will inform you of their application.
Caution
xOnly use fuel with an octane rating that is in line with the norm EN 228,
otherwise significant damage could be caused to the engine and fuel system.
Furthermore, it could lead to a loss of performance with the consequent
engine fault.
xThe use of unsuitable petrol additives could damage the engine.
xIf, in exceptional circumstances, petrol with a lower octane rating to that
recommended is used, only use moderate engine speeds and a light throttle.
Avoid using full throttle and overloading the engine. Otherwise you may
damage the engine. Fill up with fuel of a suitable octane rating as soon as
possible.
xDo not refuel if the filler indicates that the fuel contains metal. LRP (lead
replacement petrol) fuels also contain high concentrations of metal addi-
tives. This could damage the engine!
xJust one full tank of leaded fuel would seriously impair the efficiency of
the catalytic converter and could damage it.
Diesel
Diesel fuel
Diesel fuel must correspond to European standard EN 590 (In Germany, EN
590 or DIN 51628).
The use of diesel fuel with a high sulphur percentage requires shorter service
intervals ŸBooklet “Maintenance Programme” Ÿ. Your qualified work-shop will be able to tell you which countries have diesel with a high sulphur
content.
Do not mix fuel additives (thinners, or similar additives) with diesel fuel.
Winter-grade diesel
When using “summer-grade diesel fuel”, difficulties may be experienced at
temperatures below 0 °C (+32 °F) because the fuel thickens due to wax sepa-
ration. For this reason, “winter-grade diesel fuel” is available in Germany, for
example, during the cold months. It can be used at temperatures as low as
-20 °C (-4 °F).
In countries with different climatic conditions, other types of diesel fuel are
available that are suitable to local temperatures. SEAT qualified workshops
and filling stations in the country concerned will inform you on the type of
diesel fuels available.
A cold diesel engine makes more noise during winter temperatures than
summer temperatures. Furthermore, the exhaust fumes may turn slightly
bluish while the engine is heating. The quantity of exhaust gases will depend
on the outside temperature.
Filter pre-heater
Vehicles with a diesel engine are fitted with a fuel filter pre-heater. This
ensures that the fuel system remains operational to approx. -24 °C (-11.2 °F),
provided you use winter-grade diesel which is safe to -15 °C (+5.00 °F).
However, if the fuel has waxed to such an extent that the engine will not start
at temperatures of under -24 °C (-11.2 °F), simply place the vehicle in a warm
garage or workshop for a while to heat up.
Auxiliary heater
Vehicles with a diesel engine may be fitted with an auxiliary heater. The
heater runs off the fuel from the fuel tank. On doing so, smells and steam may
be noticed outside the vehicle for a short period. This is normal and it is not
an indication of a fault in the vehicle.

Page 314 of 413

Checking and refilling levels313
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Engine coolant
Introduction
Never work on the engine cooling system or if you are not familiar with the
operations to be carried out, the applicable safety standards and especially
if you do not have the instruments, liquids and tools necessary Ÿ! Have
the work carried out by a qualified workshop if you are uncertain. SEAT recom-
mends visiting a qualified workshop.
Negligent work can cause serious injury.
Additional information and warnings:
xTo wi ng m o d e Ÿpage 260
xWorking in the engine compartment Ÿpage 304
xAccessories, parts replacement, repairs and modifications Ÿpage 285
WARNING
Engine coolant is toxic!
xOnly keep engine coolant in its original container, tightly shut and in a
safe place.
xNever store engine coolant in empty food containers or bottles as other
people may accidentally drink it.
xAlways keep engine coolant out of reach of children.
xEnsure that the proportion of engine coolant additive corresponds to
the lowest outside temperature to which the vehicle will be exposed.
xIf the outside temperature is extremely low, the engine coolant could
freeze causing the vehicle to stop. As this would also cause the heating to
stop working, passengers without sufficient clothing could freeze.
For the sake of the environment
Coolants and additives can contaminate the environment. Collect any spilt
fluids in suitable containers and dispose of in accordance with legislation
and with the utmost respect for the environment.
Coolant temperature warning lamp and gauge
When driving normally, the needle will remain in the middle area. The temper-
ature may also rise when the engine is working hard, especially at high
outside temperatures and so the indicator will move quite far to the right-
hand side.
Several warning and control lamps should light up for a few seconds when
the ignition is switched. This signals that the lamp is working properly. They
will switch off after a few seconds.
Fig. 177 Engine coolant
temperature gauge on the
instrument panel: cold
area; normal area;
warning area.
AAABAC

Page 316 of 413

Checking and refilling levels315
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
WARNING
In the event of insufficient antifreeze protection in the engine cooling
system, the engine could be damaged and severe injuries caused.
xEnsure that the proportion of engine coolant additive corresponds to
the lowest outside temperature to which the vehicle will be exposed.
xIf the outside temperature is extremely low, the engine coolant could
freeze causing the vehicle to stop. As this would also cause the heating to
stop working, passengers without sufficient clothing could freeze.
Caution
Never mix genuine additives with other additives that are not approved by
SEAT. Otherwise, you run the risk of causing severe damage to the engine and
the engine cooling system.
xThe engine coolant G 12 plus-plus can be mixed with G 12 plus and G 11.
xIf the fluid in the expansion reservoir is not purple but, for example,
brown, this means that you have mixed G 12 plus-plus or G 12 plus with
another coolant. The coolant must be changed as soon as possible if this is
the case! Failure to observe this point will result in serious malfunctions and
engine damage!
For the sake of the environment
Coolants and additives can contaminate the environment. Collect any spilt
fluids in suitable containers and dispose of in accordance with legislation
and with the utmost respect for the environment.
Checking the engine coolant level and refilling
If the coolant level is low, the coolant warning indicator will light.
Fig. 178 In the engine
compartment: Marking on
coolant expansion reser-
voir.
Fig. 179 In the engine
compartment: Coolant
expansion tank cap.

Page:   < prev 1-10 ... 11-20 21-30 31-40 41-50 51-60 next >