clutch Seat Alhambra 2010 Owner's Manual

Safe driving 10
Adjusting the seat position
Introduction
Number of seats
Depending on the equipment, your vehicle has a total of five or seven seats.
Each seat is equipped with a seat belt.
Additional information and warnings:
xSeat functions Ÿpage 137
xSeat belts Ÿpage 22
xAirbag system Ÿpage 33
xChild seats (accessories) Ÿpage 42
WARNING
An incorrect sitting position in the vehicle can lead to severe injuries or
death in the event of sudden braking or manoeuvres, collision or accidents
or if the airbag deploys.
xBefore the vehicle moves, assume the proper sitting position and main-
tain it throughout the trip. This also includes fastening the seat belt.
xNever transport more people than there are seats with a seat belt avail-
able in the vehicle.
xChildren must always be protected with an approved child restraint
system suited to their height and weight Ÿpage 42, Ÿpage 33.
xAlways keep your feet in the footwell while the vehicle is in motion.
Never, for example, put your feet on the surface of a seat or on the dash
panel and never put them out of a window. Otherwise the airbag and seat
belt offer insufficient protection and the risk of injury in the event of an
accident is increased.
WARNING
Before every trip, adjust the seat, the seat belt and the head restraints and
instruct your passengers to fasten their seat belts properly.
xMove the front passenger seat back as far as possible.
xAdjust the driver's seat so that there is a distance of at least 25 cm (10
inches) between the centre of your chest and the hub of the steering wheel.
Adjust the driver's seat so that you are able to press the accelerator, brake
and clutch pedals to the floor with your knees slightly angled and that the
distance between your knees and the dash panel is at least 10 cm (4
inches). If you physical constitution prevents you from meeting these
requirements, contact a qualified workshop to make any modifications
required.
xNever drive with the backrest tilted far back. The further the backrests
are tilted to the rear, the greater the risk of injury due to incorrect posi-
tioning of the belt web or to the incorrect sitting position.
xNever drive with the backrest tilted forwards. Should a front airbag
deploy, it could throw the backrest backwards and injure the passengers of
the rear seats.
xSit as far away as possible from the steering wheel and the dash panel.
xKeep your back straight and resting completely against the backrest
and the front seats correctly adjusted. Never place any part of your body in
the area of the airbag or very close to it.
EquipmentSeats in the
frontSeats in the
second rowSeats in the
third row
5 seats23–
6 seats222
7 seats232
WARNING (continued)

Safe driving 12
Correct sitting position
The correct sitting positions for the driver and passengers are shown below.If you physical constitution prevents you from maintaining the correct sitting
position, contact a qualified workshop for help with any special devices. The
seat belt and airbag can only provide optimum protection if a correct sitting
position is adopted. SEAT recommends visiting a qualified workshop.
For your own safety and to reduce the risk of injury in the event of an accident
or sudden braking or manoeuvre, SEAT recommend the following positions:
Valid for all vehicle occupants:
xAdjust the head restraint so that its upper edge is at the same level as the
top of your head, or as close as possible to the same level as the top of your
head and under no circumstances below eye level. Keep the back of your neck
as close as possible to the head restraint Ÿfig. 1 and Ÿfig. 2.
xShort people must lower the head restraint completely, even if your head
is below its upper edge.
xTall people must raise the head restraint completely.
xAdjust the backrest to an upright position so that your back rests
completely against it.
xAlways keep your feet in the footwell while the vehicle is in motion.
xAdjust and fasten your seat belt correctly Ÿpage 22.
Also valid for the driver:
xAdjust the steering wheel so that there is a distance of at least 25 cm (10
inches) between it and your chest Ÿfig. 1 and so that you can hold the
steering wheel with both hands on the outside of the ring at the 9 o'clock and
3 o'clock positions with your arms slightly bent.
xThe adjusted steering wheel must face your chest and not your face.
xAdjust the driver's seat forwards or backwards so that you are able to
press the accelerator, brake and clutch pedals to the floor with your knees
slightly angled and the distance between your knees and the dash panel is at
least 10 cm (4 inches) Ÿfig. 1.
xAdjust the height of the driver's seat so that you can easily reach the top
of the steering wheel.
Fig. 1 The correct
distance between the
driver and the steering
wheel must be at least 25
cm (10 inches).
Fig. 2 Correct belt web
and head restraint posi-
tions.

Driving197
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Note
For automatic gearbox vehicles the key can only be removed from the ignition
lock if the gear selector lever is in position P. In this case, press and release
the selector lever locking button.
Starter button*
The starter button can only be used if there is a valid key inside the vehicle.
On leaving the vehicle with the ignition switched off, the electronic lock on
the steering column is activated when the driver's door is opened
Ÿpage 192.
Switching the ignition on/off
xBriefly press the starter button once without pressing the clutch or brake
pedal Ÿ.Emergency starting function
If the system has not recognised a valid key inside the vehicle, the emergency
starter function is activated. The corresponding information text is displayed
on instrument panel. This may occur, for example, if the key battery is flat or
very low:
xPlace the key close to the steering column immediately after passing the
start button.
xThe engine starts automatically.
Emergency disconnection
If it is not possible to switch off the engine by briefly pressing the starter
button, the emergency disconnection system should be used:
xPress the starter button twice within a second or press it once for more
than two seconds Ÿ in “Stopping the engine” on page 199.
xThe engine turns off automatically.
Re-starting the engine
If, after the engine is switched off, a valid key is not detected in the vehicle,
the engine can only be started after an interval of approximately 5 seconds.
The corresponding message is displayed on the instrument panel.
After this interval, it will not be possible to start the engine without a valid key
inside the vehicle.
WARNING
Unintentional movements of the vehicle could cause serious injury.
xWhen the starter button is pressed do not press the brake or clutch
pedal as the engine will start immediately.
Fig. 135 Detailed view of
the centre console: KESSY
starter and lock system:
Starter button.

Driving 198
WARNING
Careless or incorrect use of vehicle keys may result in severe injury and
accident.
xAlways take all the keys with you whenever you leave the vehicle. Chil-
dren and other unauthorised persons could lock the vehicle, start the engine or switch on the ignition and any electrical components such as the
electric windows.
Note
In vehicles with a diesel engine and KESSY, the starting of the engine may be
delayed due to pre-heating of the engine.
Starting the engine
Complete operations only in the sequence given:
WARNING (continued)
StepVehicles without KESSYVehicles wi th KESSY
1.Press the brake pedal and keep pressed until step 5 has been completed.
1 a.In vehicles with a manual gearbox: Press the clutch pedal all the way and keep pressed until the engine starts.
2.Put the gearstick in neutral or the selector lever in position P or N.
3.
Only in vehicles with diesel engine: To preheat, turn the key in the igni-
tion lock to position Ÿpage 196, fig. 134 . A warning lamp lights
up in the control panel
D.
4.Turn the key in the ignition lock to position Ÿpage 196, fig. 134 ;
do not press the accelerator.Press the starter button Ÿpage 197, fig. 135; do not press the acceler-
ator. To start the engine, the system should detect a valid key inside
the vehicle.
5.When the engine has started, release the key in the ignition lock.When the engine starts, release the starter button.
6.If the engine does not start, stop the process and try again after one
minute.If the engine does not start, stop the process and try again after one
minute. If necessary, perform an emergency start Ÿpage 197.
7.Disconnect the electronic parking brake when you wish to start driving Ÿpage 210.
A1
A2

Driving203
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Pedals
Do not allow floor mats or other objects to obstruct the free passage of the
pedals.Floor mats should leave the pedal area free and unobstructed and be
correctly secured in the footwell zone.
In the event of failure of a brake circuit, the brake pedal must be pressed
harder than normal to brake the vehicle.
WARNING
Objects falling into the driver's footwell could prevent use of the pedals.
This could lead the driver to lose control of the vehicle, increasing the risk
of a serious accident.
xMake sure the pedals can be used at all times, with no objects rolling
underneath them.
xAlways secure the mat in the foot well.
xNever place other mats or rugs on top of the original mat supplied by
the factory.
xEnsure that no objects can fall into the driver's footwell while the
vehicle is in motion.
Caution
The pedals must always have free and unobstructed passage to the floor. For
example, in case of a fault in the brake circuit, the brake pedal will need to be
pressed further to stop the vehicle. To press the brake pedal down further will
require more force than usual.
Fig. 136 Pedals in vehi-
cles with a manual
gearbox: accelerator;
brake; clutch.
A1A2A3
Fig. 137 Pedals in vehi-
cles with an automatic
gearbox: accelerator;
brake.
A1A2

Driving 204
Manual gearbox: Engaging gears
The position of each of the gears is shown on the gear stick Ÿfig. 138.
xKeep the clutch pedal pushed all the way down.
xMove the gear stick to the required position.
In some countries, it is necessary to press the clutch pedal to the floor to start
the engine.
Selecting reverse gear
xWith the vehicle at a standstill, press the clutch pedal to the floor and
keep pressed.
xPush the gear lever down.
xMove the gear stick to the left and then forwards to reverse gear
Ÿfig. 138 .
WARNING
When the engine is running, the vehicle will start to move as soon as a gear
is engaged and the clutch released. This is also the case with the electronic
parking brake on.
xNever engage the reverse gear when a vehicle is moving forward.
Caution
To prevent damage and avoid premature wear, please observe the following:
xWhile driving, do not leave your hand resting on the gear stick. The pres-
sure applied by your hand is transmitted to the gearbox selector forks.
xAlways ensure that the vehicle is completely stopped before engaging the
reverse gear.
xWhen changing gear, always make sure the clutch pedal is pushed right
to the floor.
xNever hold the vehicle on the clutch on hills.
Fig. 138 Gear shift
pattern of a 6-speed
manual gearbox.
AR

Driving 208
Driving down hills
The steeper the gradient, the lower the gear you will need. The lowest gears
increase the engine braking work. Never go down hills with the selector lever
in neutral N.
xYou should reduce speed accordingly.
xPress the selector lever from position D to the right into the Tiptronic
selector gate Ÿpage 207.
xGently pull the selector lever back to change down a gear.
xALTERNATIVELY: Reduce using the steering wheel paddles Ÿpage 207.
Emergency program
If all the selector lever positions on the instrument panel display are shown
with a light-coloured background, this means there is a fault in the system.
The automatic gearbox will operate in emergency programme mode. When
the emergency program is activated, it is possible to drive the vehicle
however, at low speeds and within a selected range of gears.
For the DSG
® dual clutch gearbox, in some cases, this may mean that reverse
gear does not engage. The gearbox should be checked by a qualified work-
shop as soon as possible.
Overload protection for the 6-speed DSG gearbox
®
When the clutch is overloaded, the vehicle begins to jerk and the selector
lever position indicator begins to flash. To prevent damage to the clutch, this
interrupts the power transmission between the engine and the gearbox.
There is no more traction and it is not possible to accelerate. If the clutch is
opened automatically due to overloading, press the brake pedal. Wait a few
seconds before starting to move again.
Kick-down
The kick-down system provides maximum acceleration when the gear
selector lever is in the positions D, S or in the Tiptronic position.When the accelerator pedal is pressed right down, the automatic gearbox will
shift down to a lower gear, depending on road speed and engine speed. This
takes advantage of the maximum acceleration of the vehicle Ÿ.
When the accelerator is pressed to the floor, the automatic gearbox shifts to
the next gear only after the engine reaches the specified maximum engine
speed.
Launch-Control Programme
The Launch-Control programme enables maximum acceleration while at a
standstill.
xDeactivating the TCS Ÿpage 210.
xPress and hold the brake pedal with your left foot.
xPlace the selector lever in position S or Tiptronic.
xPress the accelerator with the right foot until the vehicle reaches an
engine speed of approximately 3,200 rpm.
xLift the left foot off the brake Ÿ. The vehicle starts with maximum
acceleration.
xTurn on the TCS after accelerating!
WARNING
Rapid acceleration can cause loss of traction and skidding, especially on
slippery ground. This could cause loss of control of the vehicle resulting in
an accident and considerable damage.
xOnly use kick-down and rapid acceleration when weather conditions,
surface conditions and traffic conditions permit; accelerate and drive in a
manner that does not endanger other road users.
xPlease remember that the driven wheels can slip and the vehicle can
skid if the TCS is turned off, especially on slippery ground.
xTurn on the TCS after accelerating.

Driving209
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
Caution
xIf you stop on a hill with a gear ratio engaged, do not try to prevent the
vehicle from rolling back by pressing on the accelerator. This could cause
overheating and damage the automatic gearbox.
xNever allow the vehicle to move with the gear selector lever in N, espe-
cially with the engine turned off. The automatic gearbox will not be lubricated
and could be damaged.
Recommended gear indication
In some vehicles, the recommended gear for reducing fuel consumption is
displayed on the instrument panel:
Information for cleaning the diesel particulate filter
The exhaust gas system control recognises when the diesel particulate filter
is blocked, and helps to clean it by recommending a specific gear for driving.
It may therefore be necessary to drive with the engine at an exceptionally high
speed Ÿpage 255.
WARNING
The recommended gear display is intended as a guideline only; it should
never replace the driver's attention to driving carefully.
xResponsibility for selecting the correct gear for each situation
continues to lie with the driver, for example when overtaking, climbing a
hill or towing a trailer.
For the sake of the environment
Selecting the most appropriate gear for the situation will help you to save
fuel.
Note
The recommended gear display is switched off when the clutch pedal is
pressed.
DisplayMeaning
ˆOptimum gear.
žRecommendation to change up a gear.
ŸRecommendation to change down a gear.
WARNING (continued)

Driving213
Safety FirstOperating instructionsPractical tipsTe c h n i c a l D a t a
xPress button . At the same time, press the brake pedal hard or gently
press the accelerator pedal with the engine switched on.
xThe control lamps G on the button and H on the instrument panel go
out.
Automatic release of the electronic parking brake on starting the engine
The electronic parking brake is automatically released when the vehicle starts
moving, if the driver's door is closed and the driver is wearing his/her seat
belt. In vehicles with a manual gearbox the clutch pedal should also be
pressed to the floor before starting the engine so that the system recognises
that the parking brake should be released.
Emergency braking function
Only use the emergency braking function if the vehicle cannot be stopped
with the brake pedal Ÿ!
xPull button hard to stop the vehicle. The warning display will be
accompanied by the corresponding warning chime.
xTo stop the braking process, release the button or press the accelerator.
WARNING
The incorrect use of the electronic parking brake may result in serious acci-
dent.
xNever use the electronic parking brake to brake the vehicle except in an
emergency. The braking distance is considerably longer, because braking
is only applied to the rear wheels. Always use the foot brake.
xNever accelerate from the engine compartment with the engine running
and a gear or a gear range engaged. The vehicle could move, even if the
parking brake is applied.
Note
In vehicles with a manual gearbox: When the clutch pedal is released and the
accelerator pressed at the same time, the electronic parking brake is auto-
matically released.
Note
If the vehicle battery is flat, it will not be possible to disconnect the electronic
parking brake. Use the jump-start Ÿpage 371.
Note
When the electronic parking brake is applied or released, noises may be
heard.
Note
If the electronic parking brake has not been used for a long while, the system
sometimes performs automatic and audible checks while the vehicle is at a
standstill.
Parking
When parking your vehicle, all legal requirements should be observed.
To park the vehicle
Complete operations only in the sequence given.
xPark the vehicle on a suitable surface Ÿ.
xPress and hold the brake pedal until the vehicle comes to a standstill.
xConnect the electronic parking brake Ÿpage 212.
xFor an automatic gearbox, move the selector lever to position P.
G
G

Driving 214
xSwitch off the engine and release the brake pedal.
xRemove the key from the ignition.
xIf necessary, turn the steering wheel slightly to lock the steering.
xWith a manual gearbox, engage the 1st gear on flat ground and slopes, or
even the reverse gear on hills, and release the clutch pedal.
xEnsure that all passengers leave the vehicle, especially children.
xWhen leaving the vehicle, take all keys with you.
xLock the vehicle.
Additional information for steep slopes and hills
Before switching off the engine, rotate the steering wheel so that if the
vehicle should move then it will be held by the kerb.
xOn slopes, turn the front wheels so that they are against the edge of the
kerb.
xUphill, turn the wheels towards the centre of the road.
WARNING
The components of the exhaust system reach very high temperatures. This
could cause a fire and considerable damage.
xAlways park your vehicle so that no part of the exhaust system can
come in contact with flammable materials (such as wood, leaves, spilled
fuel, dried grass, etc).
Caution
xSpecial care should be taken when parking in areas with high kerbs or
fixed barriers. Objects protruding from the ground may damage the bumper
or other parts of the vehicle during manoeuvres. To avoid damage, stop
before the wheels touched the barrier or kerb.
xSpecial attention is required when driving through entrances, over ramps,
kerbs or other objects. The vehicle underbody, bumpers, mudguards and running gear, and the engine and exhaust system could be damaged as you
drive over these objects.
Information about the brakes
For the first 200 to 300 km (100 to 200 miles), new brake pads have not yet
reached their maximum braking capacity, and need to be run in first Ÿ.
The slightly reduced braking effect can be compensated for by increasing
pressure on the brake pedal. While running in, the full braking distance or
emergency braking distance is larger then when the brake pads have been
run in. While running in, avoid full power braking or situations requiring
braking performance. For example, in heavy traffic.
The rate of wear of the brake pads depends to a great extent on the condi-
tions in which the vehicle is used and the way the vehicle is driven. If the
vehicle is used frequently in city traffic or for short trips or driven sport style,
visit a specialist workshop regularly more frequently than advised in the
Maintenance Programme to have the bake pads checked.
If you drive with wet brakes, for example, after crossing areas of water, in
heavy rainfall or even after washing the car, the effect of the brakes is less-
ened as the brake discs are wet or even frozen (in winter). At higher speed,
dry the brakes as quickly as possible by braking gently several times. Only do
this without endangering vehicles behind you or any other road users Ÿ.
A layer of salt on the discs and brake pads will reduce brake efficiency and
increase braking distance. If you drive for a prolonged period on salted roads
without braking then brake carefully several times to eliminate the layer of
salt on the brakes Ÿ.
If the vehicle remains parked for considerable lengths of time, is used little,
or if the brakes are not used, there may be corrosion on the brake discs and
a buildup of dirt on the brake pads. If the brakes are not used frequently, or
if rust has formed on the discs, SEAT recommends cleaning the pads and